SRC H-ADV150-04-01AL User manual

Copyright By SRC
Design and Specification are subjected to change
Page 1
Scope of Supply/Bill of Material & Mounting Drawings
Part Number: H-ADV150-04-01AL / H-ADV150-04-02AL
Part Description: Top Rack –HONDA ADV150
Installation / Parts List / Bill of Material for Mounting

Copyright By SRC
Design and Specification are subjected to change
Page 2
MOUNTING DRAWINGS

Copyright By SRC
Design and Specification are subjected to change
Page 3
MOUNTING INSTALLATION
STEP 1:
The Driver seat must be moved up (as shown
in the drawing
Unscrew the Mounting screws (4 off), as
shown in the drawing, and take out
STEP 2:
Position the Mounting Bottom Plat RH & LH
(3) –2 off, as shown in the drawing, form the
downside of the Rack.
Slip-in The Bush Delrin (14) –2 off, The
Washer M5 (9) –2 off and M5 x 25 Screw (8) -
2 off and secure the threads in the Mounting
holes .

Copyright By SRC
Design and Specification are subjected to change
Page 4
STEP 3:
Orient and align the Bracket LH (6) and Bracket
RH (10) in-line with the Side Panel mounting
holes, and bring the Side panels exactly in-line
with them, and slip-in the Mounting The Screw
M8x30 (7) 4 off,The Washer M8 (12) on each
side and secure the threads .
Bracket RH & Bracket LH is shown in “As is
mounted condition”

Copyright By SRC
Design and Specification are subjected to change
Page 5
STEP 4:
Orient the Bottom Plate RH & LH (2)(11) , in-
line with the bottom side mounting holes of
the Bracket RH & LH (10)(6) , as shown.
Slip-in the Screw M6x15 (5) –4off, Washer M6
(4) –4off, in positions as shown and secure the
threads.
Bracket & Bottom Plats is shown in “As is
mounted condition”

Copyright By SRC
Design and Specification are subjected to change
Page 6
STEP 5:
Slip in the Top Rack (1) and slip-in the Taper
Ring M6 (16) 4 off , and Screw M6 x 25 (7) 4 off,
through the Mounting holes in the Top Rack
and Brackets and, secure from the bottom,
using the Nut M6 (15) –6 off and tighten it to
the torque .
Rear Rack as shown “Final Assembled condition”

Copyright By SRC
Design and Specification are subjected to change
Page 7
General Instructions
1. We request you to pay attention to the Mounting Instructions in this document and
follow the step-by-step procedures.
2. This Mounting Instruction manual is a “Do It Yourself” (DIY) fitment manual of the
Accessory part to the Vehicle. We have prepared this based on our experience and
knowledge, related to the Vehicle, Part and its functional aspects.
3. SRC cannot guarantee the interchangeability of the parts to any other manufacturer’s
accessory part. It is advised to the User, to inspect and ensure the original state of all
other Vehicle parts.
4. We request you to bear in mind, that the Installed part can change the driving
behaviour and/or the stability during driving or any other dynamic conditions.
5. If you have the appropriate tools and another person to assist you in the mounting, it
will help.
6. After Completion of the Mounting and before taking on a First ride, Ensure and Check all
functions of the Vehicle. It is always advised to check loosening of the fasteners after
the first 50 kilo meters of ride and at regular intervals.
7. We are showing here the Scope of Supply/ Installation/Parts list & BOM from SRC
8. To the maximum extent possible, our design use the current Mounting/Fitment of the
Original Equipment, so that Installation of these accessories will not affect the Payload
or Function of the Vehicle or the Part on which it is mounted to protect it
9. If any additional modifications are to be done, prior to the fitment of the accessories, it
will be explicitly specified in the instruction sheets.