Silca myfamily TECHLA 3.0 User manual

TECHLA 3.0
SERVICING MANUAL

1
Index
INTRODUCTION ............................................................................................................................................... 2
HOW TO OPEN THE SYSTEM ......................................................................................................................... 3
HOW TO CLOSE THE SYSTEM ........................................................................................................................ 4
TECHLA ID NUMBERS EXPLANATION ............................................................................................................ 5
HOW TO UPDATE THE FIRMWARE ................................................................................................................ 6
HOW TO UPDATE THE SOFTWARE ............................................................................................................. 9
HOW TO UPDATE THE DATABASE ............................................................................................................... 11
HOW TO UPDATE THE PICTURES ................................................................................................................. 13
HOW TO UPDATE LOGOS AND/OR LOAD PERSONALIZED LOGOS ......................................................... 15
HOW TO UPDATE SCREENSAVERS AND/OR PERSONALIZED SCREENSAVERS ........................................ 17
HOW TO INSERT SPECIAL CHARACATERS TO BE ENGRAVED ................................................................... 19
HOW TO SAVE A SYSTEM BACK-UP (RESTORE) FROM THE MACHINE ..................................................... 20
HOW TO RESTORE THE SYSTEM .................................................................................................................. 21
HOW TO RESET THE SERIAL NUMBER ......................................................................................................... 25
HOW TO CENTRE THE ENGRAVING ............................................................................................................ 26
HOW TO INCREASE OR DECREASE THE ENGRAVING DEPTH ................................................................... 28
HOW TO CONSULT AND EXPORT THE HISTORICAL FILE .......................................................................... 29
HOW TO MANAGE THE SECURITY PASSWORD .......................................................................................... 32
HOW TO ACCESS TO THE INTERNAL USB FLASH DRIVE ........................................................................... 33
SERVICE COMMANDS LIST ........................................................................................................................... 35
POSSIBLE PROBLEMS AND TROUBLESHOOTING .................................................................................................... 36
HOW TO GREASE THE MECHANICAL PARTS .............................................................................................. 37
COMMON ERRORS AND POSSIBLE SOLUTIONS ........................................................................................ 39
HOW TO ADJUST THE AUTO Z .................................................................................................................... 40
HOW TO SOLVE 1206 ERROR ....................................................................................................................... 41
HOW TO ALIGN THE PORTCULLIS ............................................................................................................... 43
HOW TO WELD THE CARRIAGE SENSORS WIRE ......................................................................................... 44
HOW TO SUBSTITUTE THE BATTERY BEFORE IT GETS LOW ...................................................................... 45
HOW TO MECHANICALLY ADJUST THE AUTO Z ........................................................................................ 48
HOW TO BEND THE LEAF SPRING OF THE CARRIAGE ............................................................................... 50

2
INTRODUCTION
Techla software application has
two passwords
to enter in the menus:
Both passwords can be inserted by pressing in the home page.
DIFFERENCES BETWEEN THE TWO PASSWORDS:
The
BASIC
password is →
09876
and it gives the access to the “first level” menus:
• change the software language
• manage the security password
• update firmware, software and database
• historical file consulting and downloading
The
ADMIN
password is →
987654321
and it gives the access to the whole system:
• engraving areas parameters
• general settings (engraving depth, axis centering, etc.)
• operative system
• status sensors page (I/O button)
The
ADMIN
password leaves the system opened,
so it means that it is always accessible to everybody until it will be closed again.
To close the system read the instructions “HOW TO CLOSE THE SYSTEM”.
BASIC
PASSWORD
ADMIN
PASSWORD

3
HOW TO OPEN THE SYSTEM
If the machine is switched off, switch it on and this screen will appear:
Press and this screen will appear:
Insert the password
987654321
and press
Then proceed with the needed operations.
! A T T E N T I O N !
The
ADMIN
password
OPENS
the system:
it means that the menu remains
accessible
and anybody can use it.
“
CLOSE
” the system to avoid problems!

4
HOW TO CLOSE THE SYSTEM
There are two ways to close the system.
FIRST METHOD
To
CLOSE
the system, in the home page, press and press “
SET
” button.
This screen will appear:
Press the “
SERVICE COMMAND
” field and the 0 (zero) will become highlighted in GREEN.
In this field, insert the number
9060
and press .
The system is now closed.
SECOND METHOD
Scan this following barcode to the barcode reader:
The system is now closed.

5
TECHLA ID NUMBERS EXPLANATION
The page that appears after the button is pressed, shows different numbers on the bottom part:
From the left:
•
40
→ is the total engravings done by the machine
•
132:01
→ Switcing ON total time (hh:mm)
•
1:57
→ Total working time (hh:mm)
•
0:28
→ Last engraving lasting
•
G: H:
→ Plugged USB flash drive
•
00.67
→ Software version number
•
2023.02.09
→ Software release date
•
397 / 27
→ Electronic board version
•
0032
→ Database version
•
10590
→ Mechanic serial number
•
57254
→ Electronic board serial number
•
2023
→ Year of production
•
07
→ Week of production
•
179
→ Firmware version

6
HOW TO UPDATE THE FIRMWARE
If the machine is switched off, switch it on and this screen will appear:
Insert the USB flash drive with Firmware saved in, in the frontal panel:
Press and this screen will appear:
Insert the password
09876
, press and this screen will appear:

7
Press "
UPDATE
" button and this list will appear:
Press to proceed.
The Firmware loading process will start and this screen will appear:
After 5/6 minutes, some different screens will appear automatically.
Then, the Software loading process will start automatically and this screen will appear:

8
The loading process will take around 5 minutes; this message will appear:
Press “
Close
” button and this screen will appear:
Switch the machine OFF and leave the USB flash drive plugged IN the machine.
Wait 10 seconds and switch the machine ON again.
The home page will appear.
Do not touch anything and wait for this screen:
Remove the USB flash drive.
The update process is finished!

9
HOW TO UPDATE THE SOFTWARE
Switch the machine ON and wait for the home screen:
Insert the USB flash drive, with the Software files, into the slot on the front of the machine,
as shown in the following photo:
Press and this screen will appear:
Insert the password
09876
and press to proceed.
This screen will appear: