Silux Home Seeker User manual

OPER AT ION MANUA L
SC-SK01
Seeker
Part of the

Appendix I:
1. Introduction to Silux Home
®
2. Introduction to the Seeker
®
3. Applications
4. Electrical Specifications
5. Instructions
I. Configuring the Seeker
®
II. Installing the Seeker
®
III. Installing the external power supply
IV. Replacing the AA 1.5V batteries
V. How to pair with Silux Home
®
Devices
VI. How to delete paired Silux Home
®
devices
VII. How to control a Silux Home
®
device
VIII. Hubcentric Topology
IX. What is a Trigger
X. Factory Reset
6. Versions and changes
7. More Silux Home
®
automation products
Appendix II:
1. Troubleshooting
2. Warranty
I. What this warranty covers
II. What period does this warranty cover
III. What Silux Home
®
will do to correct any problems
IV. What is not covered by this warranty
3. Support
4. Disclaimer of Liability

Appendix I:
1. Introduction to Silux Home®
PLEASE NOTE: You are not able to connect directly to the Seeker®.You will
be required to connect directly to the Intellihub®to ensure you can control all
devices via the Intellihub®and Silux Home®app.
The idea behind the Silux Home®automation series is to have a fully
automated lifestyle. No longer will you need to push a button to switch on
appliances or lights; it will simply be switched on for you with motion,
schedules and scenes. You can schedule your geyser or water heater to turn
on and set it to the temperature you wish. Your irrigation system can be
automated, and so much more can be controlled, the sky is the limit, and all
this under one app, all controlled from one place. You can create scenes or
even control a couple of appliances from the convenience of your living room
or anywhere across the world using any smart device running Android or iOS.
At Silux Home®, we tried to keep our products as affordable as possible,
without compromising quality. Our devices are specially designed to make it
as easy as possible to install with easy usability and a wide range of
applications. With encrypted data control, you are also protected from the
outside world, providing you with a peace of mind. We have thought of
everything. What are you waiting for? Install Silux Home®and let us help you
control your world safely, securely, and efficiently.
2. Introduction to the Seeker®
The Seeker®is one of the many useful and wonderful products that form part
of the Silux Home®automation series. The purpose of this product is to
control your lights or any other Silux Home®product with motion. Your lights
will turn on when entering a room and you will be able to set the time on the
Silux Home®app for how long they should stay on.
Warning: Please follow all safety precautions when installing this
product. It is always recommended to use a qualified electrician. Silux
Home®and its distributors and resellers can not be held responsible for
any injury or death.
Seeker®
Device1
Device2
Device3
Device4
IntelliHub®
Device1

3. Application
The Seeker was designed to compliment your Silux Home®System. The
Seeker®can be used to control any of your Silux Home®devices through
Scenes, as well as inform your IntelliHub®or Silux Home®Security panel of
detected movement.
4. Electrical Specifications
Operating Battery: x2 AA 1.5V Batteries
External Power Supply: Input: 110V AC – 230V AC
Output: 5V /DC
Operating Temperatures: -5°C – 60°C
Seeker®Layout
5. Instructions
I.Configuring the Seeker®
There are 2 configuration settings, namely time delay and sensitivity.
Time delay refers to the amount of time the Seeker®will wait after triggering
before triggering again.
Sensitivity refers to a combination of distance and movement required to
trigger the Seeker®. Higher sensitivity allows for a greater distance and less
movement, while lower sensitivity requires more movement and a shorter
distance.
The settings are as follows:
Time Delay
1. 1 Minute 40 seconds
2. 3 Minutes 10 Seconds
3 6 Minutes 20 Seconds
Sensitivity
1. High sensitivity
2. Medium sensitivity
3. Low sensitivity
Please note: Setting your Seeker to a shorter time delay will drain your
batteries quicker.
Triger light
Optical lense
External
Power hole
Mounting
Hole
Big Slot
Mounting
Hole
Battery Cutout
Battery Cutout
Teach Button
Trigger light
External Supply
Connection
SENSITIVITY
ON
TIME DELAY
123
ON
23
SET PINS ON OR OFF
SET PINS ON OR OFF

1
2.1
3
Big Slot
Battery Cutout
Battery Cutout
Big Slot
Small Slot
Small Slot
Small Slot
4
3M
3M
2.2 Adhesive
Liner
We recommend testing your settings before permanent installation of the
Seeker®
II. Installing the Seeker®:
You have the option to mount the Seeker®on the ceiling using the supplied
screws or supplied 3M double sided tape.
1. Open the plastics by holding the back plastic firmly and turning the lid
anticlockwise.
2.1.1 If using screws use the backside plastics and mark with a pencil or pen
where your holes are going to be.
2.1.2 Drill holes in the ceiling and screw the back side against the ceiling.
2.2.1 If using the double sided tape, remove the first liner of the tape, apply the
tape to the backside plastics, let the adhesive set before you try and remove the
second liner.
2.2.2 Place the back side firmly onto the ceiling, where you would like your PIR
to be positioned and let it set.
3. Insert the two AA Batteries into the battery holders. The Seeker®will now be
powered on. You can keep an Eye on your battery levels using the Silux Home®
App. Please refer to “IV. How to pair with Silux Home®Devices”
4. Place the lid over the plastic and turn the lid clockwise.
Please make sure that the big pin on the lid slots into the big groove on the
back plastic.
Big Slot
III. Installing the external power supply:
There will be a Silux Home®external power supply included with the package.
You have the choice to install it. This will ensure that the Seeker®never runs flat.
1. Please make sure the power is off before supplying 110V AC – 230V AC to the
external power supply.
2. Push the connector through the back of the plastic
3. Plug the connector into the 5V socket on the Seeker®.
4. It is now safe to power the 110V AC – 230V AC back on again. The Seeker®
will also be powered on.

5. After the Seeker®’s external power is switched on, please
refer to How to pair with Silux Home®Devices.
6. Place the lid over the plastic and turn the lid clockwise.
Please make sure that the big pin on the lid slots into the big
groove on the back plastic.
IV. Replacing the AA 1.5V batteries:
There will be two AA batteries supplied with the product. The two
batteries will have a life span of 1 to 2 years, depending on the
sensitivity setting and how often the Seeker®is triggered.
1. Open the plastics by turning the top plastic anticlockwise and
removing the lid.
2. Pop out the two old AA batteries and replace it with two new AA
batteries. The Seeker®will now be powered on.
3. Place the lid over the plastic and turn the lid clockwise. Please
make sure that the big pin on the lid slots into the big groove on
the back plastic.
*Please Note: It’s not necessary to pair the Silux Home®
devices again after replacing the batteries.
V. How to pair with Silux Home®Devices:
1. Ensure the Silux Home®device you would like to pair is
powered on.
This can be any device excluding triggers such as the Touch
Lamina. Press the Teach button on the Silux Home® device in a
similar area or room to the Seeker position. The light will start
flashing.
2. Ensure the Seeker®is on, then press the Teach button on the
Seeker®. The light on the Seeker®will start flashing.
3. The light will switch off once successfully paired. If the light
stays on, the pairing was unsuccessful and you should wait for
30 seconds for the light to go off before trying again.
OFF
123
ON
4
Big Slot
Battery Cutout
Battery Cutout
Big Slot
Small Slot
Small Slot
Small Slot
6
We recommend testing your settings before permanent installation of the
Seeker®
II. Installing the Seeker®:
You have the option to mount the Seeker®on the ceiling using the supplied
screws or supplied 3M double sided tape.
1. Open the plastics by holding the back plastic firmly and turning the lid
anticlockwise.
2.1.1 If using screws use the backside plastics and mark with a pencil or pen
where your holes are going to be.
2.1.2 Drill holes in the ceiling and screw the back side against the ceiling.
2.2.1 If using the double sided tape, remove the first liner of the tape, apply the
tape to the backside plastics, let the adhesive set before you try and remove the
second liner.
2.2.2 Place the back side firmly onto the ceiling, where you would like your PIR
to be positioned and let it set.
3. Insert the two AA Batteries into the battery holders. The Seeker®will now be
powered on. You can keep an Eye on your battery levels using the Silux Control®
App. Please refer to “IV. How to pair with Silux Control®Devices”
4. Place the lid over the plastic and turn the lid clockwise.
Please make sure that the big pin on the lid slots into the big groove on the
back plastic.
III. Installing the external power supply:
There will be a Silux Control®external power supply included with the package.
You have the choice to install it. This will ensure that the Seeker®never runs flat.
1. Please make sure the power is off before supplying 110V AC – 230V AC to the
external power supply.
2. Push the connector through the back of the plastic
3. Plug the connector into the 5V socket on the Seeker®.
4. It is now safe to power the 110V AC – 230V AC back on again. The Seeker®
will also be powered on.

VI. How to delete paired Silux Home®devices:
To delete a Silux Home®device from the Seeker®, both the
Seeker®and device needs to be on.
1. Press the Teach button on the Seeker®. The light on the
Seeker®will start flashing. Press the Teach button on the Seeker®
a second time. The light on the Seeker®will flash faster.
2. Press the Teach button on the device you wish to clear. The
light will switch off and stop flashing on both devices once
successfully cleared. If the light stays on the clearing was
unsuccessful and you should wait for 30 seconds for the light to go
off before trying again.
VII. How to control a Silux Home®device:
Once the Seeker® is paired to a device, any device can be
controlled by the Seeker®. All you need to do is select the Seeker®
on the app and select which Silux Home®devices you wish to
control.
The seeker will be discoverable by the app after it first trigger
after being paired. This could take up to 5 minutes depending on
your timer settings.
Discovering Seeker from the Silux Home®App :
1. Open your Silux Home®App.
2. Tap on the “Add device” button.
3. Look for the Seeker®in the list of devices, by its serial number
(located on the sticker on the underside of the Seeker®plastics, or
on the Seeker®packaging)
4. Select the Seeker®to give it a name and set other options
5. Tap save and the Seeker®will be available to link to schedules
or device.

TV
TV
Water Heater
IntelliHub
Tier 1 Tier 2 Tier 3
VIII. Hubcentric topology.
Your Silux Home®automation system uses a technology known as
Hubcentric topology. This means that all your devices communicate with
each other. In larger areas, it is possible that a device might be too far from
the IntellihHub®to communicate reliably. Your IntelliHub®will then use other
devices which are more in range to create a more reliable connection to the
out of range device. The distance at which your IntelliHub®can communicate
with your Silux Home®devices varies according to the environment. The
IntelliHub®has been developed to achieve a distance of 20m, however, thick
walls, large electrical appliances and long distances are 3 factors that can
limit communication with Silux Home®devices. Use the “diagnostics” section
of your Silux Home®app to diagnose any issues you might be experiencing
with communication on your Silux Home®Network.
IX. What is a Trigger:
An ‘trigger’ is a device, used to control a Silux Home
®
device. Think of it
as a remote control. This device will only be on for a brief period of time
while sending the command to your Silux Home
®
device and will go back
into sleep mode if the command was successful. Because this device will
be in sleep mode, most of the time, it doesn’t form part of the
intercommu-nication system. Please see the diagram above for the
intercommunica-tion system.
*Please Note: The Seeker®and Touch Lamina®are examples of end points.
X. Factory Reset:
This function will remove all paired devices and restore the settings to the
original state. Press the Teach button on the Seeker
®
5 consecutive
times. On the 5th time, the light will flash 3 times. Your device will now be
restored to its default state.

6. Versions and changes
Currently, there’s only one variant of this product.
The Seeker
®
model no: SC-SK01
User Manual Revision No: 0.01
This user manual may be outdated. Please visit our website at
www.siluxhome.com for updated models & versions, updated user
manuals, future products and to see the rest of the wonderful
products Silux Home
®
has to offer.
7. More Silux ®automation products
Product
Hub
Relay Module Dry contact
Relay Module
Relay Module Dimmable
Repeater/Range Extender
PIR Sensor
Touch Plate SA
Touch Plate USA
Plug
Smoke Detector
Water Heater / Geyser
High Power Appliances
Irrigation
Gas leak Detector
Garage Tilt
Water & Temperature Sensor/Puk
Security Module
Silux Home®Name
IntelliHub®
Collector®
Collector Relay®
Collector Dimmable®
Silux RPT®
Seeker®
Touch Lamina Altus®
Touch Lamina Artatus®
Electrifier®
Halitus®
Thermo Stabilizer®
Tolleno®
Saturizer®
Garseous®
Tylten Pro®
Elements®
Armaduras®
*Please note: Not all the products on this list are available yet, but will
become available in the near future. This list can change at any time.
Please refer to www.siluxhome.com for new and discontinued
products. New products will be added in time to come as well.

Appendix II
1. Troubleshooting
Please visit our website at www. .com/FAQ for detailed list of
all the Frequently Asked Questions.
• Ensure that the AA Batteries are properly inserted.
• Ensure that the batteries are not flat.
• When using the Silux Home
®
external power supply make sure the
light on the external power supply is on and the 5V
connector is correctly connected onto the Seeker
®
.
• Ensure that the light flashes when pressing the Teach button.
• Ensure that the Seeker
®
is correctly paired to a Silux Home
®
Device.
• Ensure the IntelliHub
®
is on and connected to your local network.
• Verify that you have the latest app installed on your smart device.
• Verify that the Silux Home
®
device is added to your device list when
using the app.
• Verify that you have the correct Silux Home
©
device selected when on
the app.
• Verify that you have the latest firmware installed on the IntelliHub
®
2. Warranty
I. What this warranty covers:
Silux Home®warrants to the original purchaser of this Silux Home®product
that the product shall be free from defects in design, assembly, material, or
workmanship under normal use and operation.
Silux Home®‘s sole and exclusive obligation under the foregoing warranty
shall be to repair or replace, at its option, any defective product that fails
during the warranty period. The expense of removal and reinstallation of any
item is not included in this warranty.
WARNING: Silux Home®and its distributors and resellers cannot be
held responsible for any damages this product might have caused
including 3rd party damages.
II. What period does this warranty cover:
Silux Home®warrants this product for 12 months.
III. What Silux Home®will do to correct any problems:
Silux Home®will repair or replace, at its option, any defective product free of
charge (except for shipping charges for this product). Silux Home®reserves
the right to discontinue any of its products without notice and disclaims any
limited warranty to repair or replace any such discontinued products.

5. After the Seeker®’s external power is switched on, please refer
to How to pair with Silux Control®Devices.
6. Place the lid over the plastic and turn the lid clockwise. Please
make sure that the big pin on the lid slots into the big groove on
the back plastic.
IV. Replacing the AA 1.5V batteries:
There will be two AA batteries supplied with the product. The two
batteries will have a life span of 1 to 2 years, depending on the
sensitivity setting and how often the Seeker®is triggered.
1. Open the plastics by turning the top plastic anticlockwise and
removing the lid.
2. Pop out the two old AA batteries and replace it with two new AA
batteries. The Seeker®will now be powered on.
3. Place the lid over the plastic and turn the lid clockwise. Please
make sure that the big pin on the lid slots into the big groove on
the back plastic.
*Please Note: It’s not necessary to pair the Silux Control®
devices again after replacing the batteries.
V. How to pair with Silux Control®Devices:
1. Ensure the Silux Control®device you would like to pair is
powered on.
This can be any device excluding triggers such as the Touch
Lamina. Press the Teach button on the Silux Control® device in a
similar area or room to the Seeker position. The light will start
flashing.
2. Ensure the Seeker®is on, then press the Teach button on the
Seeker®. The light on the Seeker®will start flashing.
3. The light will switch off once successfully paired. If the light
stays on, the pairing was unsuccessful and you should wait for 30
seconds for the light to go off before trying again.
IV. What is not covered by this warranty
Upon claiming this warranty, all above warranties are null and
void if the purchased Silux Home®product is not returned for an
authorized inspection, at the sole expense of the purchaser, or if
Silux Home®determines that the Silux Home®product has been
improperly installed, altered in any way, or opened/tampered with.
The Silux Home®product warranty does not protect against
instances of uncontrollable natural disasters such as flood,
lightning, earthquake, war, vandalism, theft, normal use wear and
tear, erosion, depletion, obsolescence, physical damage, water
damage, damage due to low voltage disturbances (i.e. brownouts
or sags), non-authorized program, or system equipment
modification or alteration.
3. Support
Please visit our website at www.siluxhome.com for any other
support, products, future products, and updated user manuals.
4. Disclaimer of Liability
Please read this user manual thoroughly before using the
IntelliHub®. Follow all safety precautions when installing this
product. It is always recommended to use a qualified
electrician.
Under no circumstances shall Silux Home®or its associates
be liable for any direct, indirect, incidental, special or
consequential damage that results from the use of or inability
to use the Silux Home®products. By using the IntelliHub®or
any other Silux Home®Automation products, you expressly
agree that the use of these products are at own risk. Neither
Silux Home®nor its affiliates, subsidiaries, or designees nor
each of their respective officers, directors, employees,
agents, third party content providers, designers, contractors,
distributors, merchants, sponsors or licensors can be held
responsible for any injury, death or damages this product
might have caused.

Download Our Free Silux Home App
Google Play App Store
Available on
or in the User Manual of the product under the Warranty secon.
SILUX WARRANTY CARD
The full text of warranty is available on our website
www.siluxhome.com
Please take a moment to fill out your informaon
.
Please return the warranty card with defective product and the sales receipt as
proof of the date purchase.
Warranty cannot be carried out without it.
Product:
Model No:
Serial No:
Date of Purchase:
Name:
Surname:
E-Mail Address:
Phone No: +
Address:
Country:
D D M M Y E A R
Cut Here