SilverStar WASH 250 Series User manual

WASH 250
USER MANUAL
www.yagang.com

Please read over this manual before operation the light

1. Open the box and checking
Congratulations on choosing our products! Please carefully read this instruction manual in its
entirety and keep it well for using reference. This manual contained about the installation and the
relative using information of this products. Please according to this manual's relative speaking when
using this equipment.
This equipment was made of new style, high intensity plastic . It fully shows the modem times
light characteristic with beauty structure. And it was made according to CE standard. Fully up the
international standard of DMX512 agreement. Master or slave in phase control. Can be use in large
entertainment, theater, performing and playing hall, etc.
This product uses MSR 250/2 electrical arc lamp. When receiving this product please carefully
b
ring and put; and check that whether this equipment has been damaged or not during transportation.
And please also check the following thing was enclosed:
Signal line ----------------------- one piece Safety string ----------------------- one pieces
User Manual----------------------- one set
Every person involved with installation and maintenance of this device have to:
- be qualilfied
- follow the instructions of this manual
eep this device away from rain and moisture!
nplug mains lead before opening the housing!
OR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
EFORE YOU INITIAL START - UP!
his device has left our premises in absolutely perfect condition. In order to maintain
this condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes writtenin this manual.
he manufacturer will not accept liability for any resulting damages caused by the non-
observance of this manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not
subject to warranty.
Never let the power-cord come into contact with other cables! Handle the power-cord
and all connections with the mains with particular caution!
Make sure that the available voltage is not higher than stated on the rear panel.
Always plug in the power plug least. Make sure that the power-switch is set to OFF-
position before you connect the device to the mains. The power-plug has to be
accessable after installing the device.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the
device and the powercord from time to time.
2. Safety instructions
CAUTION:
Important:
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
K
U
F
B
T
B
W
e careful with your operations.
ith a high voltage you can suffer a dangerous electric shock when touching the
wires!
T
-1-

¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
by the plug. Never pull out the plug by tugging the power-cord.
This device falls under protection class I. Thereforeit is essential toconnect the
yellow/green conductor to earth.
The electric connection, repairs and servicing must be carried out by a qualified
employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp s
life.
During the initial start-up some smoke or smell may arise. This is a normal process and
does not necessarily mean that the device is defective.
Do not touch the device s housing bare hands during its operation (housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
CAUTION :
EYE DAMAGES !
Avoid looking directly into the light source(meant especially for epileptics) !
℃
3. Operating determinations
This device is a moving-head spot for creating decorative effects and was designed for
indoor use only.
If the device has been exposed to drastic temperature fluctuation (e.g.After transport-
ation), do not switch it onimmediately.The arising condensation water might damage
your device. Leave the device switched off until it has reached room temperature.
Never run the device without lamp!
Do not shake the device.Avoid brute force when installing or operating the device.
Never lift the fixture by holding it at the projector-head, as the mechanics may be
damaged. Always hold thefixture at the transport handles.
When choosing the installation-spot, please make sure that the device is not exposed to
extreme heat, moistureor dust.There should not be any cables lying around.You
endanger your own and the safety of others!
The minimum distance between light-output and the illuminated surface must be more
than 2 meters.
Make sure that the area below the installation place is blocked when rigging, derigging
or servicing the fixture.Always fix the fixture with an appropriate safety-rope. Fix the
safety-rope at the correct holes only.
Only operate the fixture after having checked that the housing is firmly closed and all
screws are tightly fastened.
The lamp must never be ignited if the objective-lens or any housing-cover is open, as
discharge lamps mayexplose and emit a high ultraviolet radiation, which may cause
burns.
The maximum ambient temperature ta = 45 must never be exceeded. Otherwise, the
lamp is switched off andthe fixture is out of operation for 5 minutes
..
-2-

4.Descriptionof the device
Front panel:
10 - Mode-button
11 - Enter-button
12 - Up-button
13- Down-button
14- Display
Rear panel:
5 -Power switch
6 -DMX output
7- DMX input
8- Power cord
9- Fuse holder
1- Moving head
2-Yoke
3- Carry handles
4 - Base
-3-
POWERSWITCH
POWERSUPPLY T3.15A@230V
T6.3A@120V
LAMP:MSD 250/2
MSD 250
FUSE
1=GND
2=SIG.-
3=SIG.+
SERIAL DATALINK
LIGH TING CO NTROL P ROTOCOL: DMX512
Serialnumber:
14

5.Installion
To insert the lamp MSR 250/2 loosen the lamp cover at the rear of head (see the
drawings ) byremowing the 3 fastening screws which are marked "X,Y,Z". Carefully pull
out the cover with the lamp socketassembly.If changing the lamp, remove the old lamp
from the socket. Insert the lamp to the socket.
Do not install a lamp with a higher wattage! A lamp like this generates temperatures the
device is not de-signed for.Damages caused by non-observance are not subject to warranty.
Please follow the lamp manufacturer notes!Do not touch the glass-bulb with bare hands
during the installation! Make sure that thelamp is installed tightly into the lampholder
system.
Reclose the lamp cover and tighten the 3 screws.
.Lamp assembly:
5.1 Fitting the lamp
3 phillips screws "X,Y,Z"
3 adjustment screws "A,B,C"
5.2 Lamp adjust
The WASH250 lampholder is alignedat
the factory. Due to differences between
lamps , fine adjustment may improve light
performance.Strike the lamp,open the shutter
and theiris,setthe dimmer intensityonto
100%andfocus the lighton a flatsurface
(wall).Center a hot-spot(the brightest part of
the image) by using the 3 adjustment screws
"A,B,C".Turnone screw after another a
quarter-turn clokwise(counter-clokwise. If
you cannotdetect the hot-spot,adjust the
lamp until the light is evenly distributed.
-4-
Lamp assembly

5.4 Rigging the fixture
DANGER TO LIFE:Please consider the respective national norms during the
installation!The installation must only be carried out by an authorized dealer!
Caution:
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
The installation of the projector has to be built and constructed in a way that it can hold
10 times the weight for 1 hour without any harming deformation.
The installation must always be secured with a secondary safety attachment, e.g. an
appropriate catch net. This secondary safety attachment must be constructed in a way
that no part of the installation can fall down if the main attachment fails.
When rigging, derigging or servicing the fixture staying in the area below the
installation place, on bridges, under high working places and other endangered areas is
forbidden.
The operator has to make sure that safety-relating and machine-technical installations
are approved by an expert before taking into operation for the first time and after
changes before taking into operation another time.
The operator has to make sure that safety-relating and machine-technical installations
are approved by an expert after every four year in the course of an acceptance test.
The operator has to make sure that safety-relating and machine-technical installations
are approved by a skilled person once a year.
The projector should be installed outside areas where persons may walk by or be seated.
IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE,
including (but not limited to)calculating working load limits, installation material
being used, and periodic safety inspection of all installationmaterial and the projector.
If you lack these qualifications, do not attempt the installation yourself, but instead use
a professional structural rigger. Improper installation can result in bodily injury and or
damage to property.
The projector has to be installed out of the reach of people.
If the projector shall be lowered from the ceiling or high joists, professional trussing
systems have to be used. The projector must never be fixed swinging freely in the room.
Projectors may cause severe injuries when crashing down! If you have doubts
concerning the safety of a possible installation, do NOT install the projector!
-5-
5.3 Adjusting beam angle
Adjusting screw
Fresnel lens
The Fresnel lens system can be
configured in the range between
8 and 22 .To set the desired
b
eam angle, and loose 2 adjusting
screws on the Fresnel lens unit
and adjust the required beamangle.
Tighten the adjusting screws again
and fix back the front cover.
°°

5 Connection to the mains.5
Verify the powersupply settings before applying power!
The occupation of the connection-cables is as follows
If you wish to change the power supply settings,see the chapter Appendix.
Connect the fixture to the mains withthe enclosedpower cable and plug.
The earth has to be connected!
:
Pin
Cable (EU) International
Brown
Lightblue
ellow/Green
Y
Black
White
Green
Live
Neutral
Earth
L
N
Cable (US)
5.5 DMX-512 connection/connection between fixtures
-6-
holde
¾
¾
Before rigging make sure that the installation area can hold a minimum point load of 10
times the projector s weight.
The projector can be placed directly on the stage floor or rigged in any orientation on a
truss without altering its operation characteristics.
For overhead use, always install a safety-rope that can hold at least 10 times the weight
of the fixture. You must only use safety-ropes with screw-on carabines. Pull the safety-
rope through the two apertures on the bottom of the base and over the trussing system
¾

Control board Function :
Onlyuse a stereoshielded cable and 3-pin XLR-plugsand connectorsin order to connect the
controller with the fixture or one fixture with another.
DMX-OUTPUT DMX-input
1
2
3
- Ground
-Signal (-)
-Signal (+)
1 1
2
3
-Ground
- Signal (-)
- Signal (+)
Occupation of the XLR-connection:
XLR mounting-socket: XLR mounting-plug:
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 resistor between Signal(-) and Signal(+) intoa 3-pin XLR-plug and plug it inthe
DMX-output of the lastfixture.
Ω
5Pins canon( )plug
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pins canon(socket)
5Pins canon(socket)
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3plug
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pins canon( )
The transform of the controller line of 3 pins and 5 pins (plug and socket)
6.Control board Operation
-7-
MODE FUNCTION CONDITION
YES--negative direction
YES--negative direction
Vertical movement in positive or negative direction
Address code set
Reset YES--reset
Working mode
DMX512 mode
Automatic
Slave mode
Lamp switch Lamp on
Lamp off
Software version
Lamp hot
Lamp error

7. DMX512 Channel Function
Control board operation way:
LED
1.Select working mode by pressing MODE.
2.Press ENTER to confirm the selection.
3.Press UP and DOWN to select working condition.
4.Press ENTER to confirm the selection.
CHANNEL FUNCTION
PAN
TILT
PAN FINE (proportional)
TILT FINE (proportional)
Speed of PAN/TILT movement
Lamp on/off & reset
Rainbow Colors Wheel
Keep
Shutter, strobe
Dimmer intensity (Proportional)
-8-

CHANNEL2: TILT
CHANNEL1: PAN
Effect
Value
EffectValue
-9-
255
0
100
0
255
0
100
0

CHANNEL3 ： PAN FINE (proportional)
0
255 100
Effect
Value
Effect
Value
CHANNEL4 ： TILT FINE (proportional)
-10-
Finecontrolof
pan movement
(16 Bit)
0
0
255 100 Fine controlof
pan movement
(16 Bit)
0

CHANNEL5 ： Speed of PAN/TILT movement
EffectValue
Slow
Fast
Slow
Fast
CHANNEL6 ： Lamp on/off & reset
EffectValue
-11-
240-255
230-239
140-229
128-139
0-127
94-100
90-93
55-89
50-54
0-49
Nofunction
Lamp off after
Nofunction
Lamp on after
Nofunction
3seconds
3 seconds, Reset
255
0
100
0

CHANNEL7: Rainbow ColorsWheel
Effect
Value
CHANNEL8: Keep
255
0
0
100
Effect
Value
-12-
Backwards rainbow
No rotation
Forwards rainbow
effect from slow to fast
effect from slow to fast
UV-filter
Pink
Blue
Orange
Green
Magenta
Yellow
Red
Open/white
193-255
191-192
128-190
114-127
100-113
86-99
72-85
58-71
44-57
30-43
16-29
0-15
75-100
74
50-73
44-49
39-43
33-38
28-32
22-27
17-21
11-16
6-10
0-5

CHANNEL9: Shutter/strobe
Effect
Value
CHANNEL10: Dimmer intensity (Proportional)
224-255
192-223
160-191
128-159
96-127
64-95
32-63
0-31
87-100
75-86
62-74
50-61
37-49
25-36
12-24
0-11
Shutter Open
Random strobe-
Shutter Open
Pulse-effect in
Shutter Open
Strobe-effect from
Shutter Open
Shutter closed
effect from slow to
fast
sequences from
slow to fast
slow to fast (max 10
Flashes/s)
255
0
100
0
Effect
Value Brightest
Black
-13-

8.
US-model:
EU-model:
Philips MSD 250/2 or GY 9,5
Voltage............................AC100/110/120V , 50/60Hz
Fuse................................T 6.3A@120V
Voltage............................AC220/230/240V ,50/60Hz
Fuse ................................T10
MSD 250
8 ~22 manual zoom system
Pan 530 Tilt 280 (micro-step scan)
Auto-reset system& Pan/Tilt control sensitivity control
:
6 dichroiccolors & white
luorescent effect and increase color temp. slip and decreasecolor temp. slips
-Stands directlyon the floor
-Mounts horizontally or vertically with 2 clamps
-1 truss orientation
-Safety chain/cord attachment bolt
-Maximum ambient temperature ta: 45
-Maximum housing temperature tb (steady state): 80
-Min.distance from flammable surfaces: 0.5m
-Min.distance to lighted object: 2.0m
-Length of base (including handles): 379mm
-Width ofyoke: 428 mm
-Height (head horizontal): 476 mm
-Weight (net): 35.5 kg
RatedPower 500W
DMX512 Channel 10CHS
Luminous 18000 LUX
：
：
：
°°
°°
℃℃
Dimmer:
Scan
Smooth dimmer 0-100%
:
ColorWheel
Minimum distances:
Dimensions and weight:
Rigging:
Temperatures:
Technical specifications
A @230V
Lamp :
Optical system:
-High luminous-efficiency parabolic reflector
-
-Fresnel lensof diameter 200 mm
-
-
--F
-14
-

Min. beam angle 8 °
Max. beam angle 22 °
8
°
3
2
1
0
1
2
320 Distance (m)
22408960 1000 560 LUX
0,7 1,4 2,1 2,8 Diameter(m )
51015
Beam opening (m)
4
3
2
1
0
1
2
3
420 Distance (m)
10154050 450 255 LUX
1,94 3,89 5,83 7,77 Diameter(m )
51015
Beam opening (m)
22
°
0
10000
(LUX)
8000
6000
4000
2000
01 0,8 0,6 0,4 0,2 0,2 0,4 0,6 0,8
Diameter (m)
Distance=5m
1
22 radiation angle °
832 208 92 52 Foot-candles
376 94 42 23 Foot-candles
929
(Foot-candles)
743
557
371
186
0
8 radiation angle °
-15
-
Beampath:

9. Maintenanceand cleaning
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid
residues must not buildup onor within the fixture. Otherwise, the fixtures light-output will
be significantly reduced. Regular cleaning willnot only ensure the maximum light-output,
b
ut will also allow the fixture to function reliably throughout its life.A soft lint-free cloth
moistened withany good glasscleaning fluid is recommended,under nocircumstances
shouldalcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up
residues, reducing thelight-output very quickly.The cooling-fans should be cleaned
monthly.
Thegobos may be cleanedwitha softbrush.The interiorof the fixture should be cleaned at
least annually usinga vacuum-cleaner or an air-jet.
The dichroic colour-filters, the gobo-wheel and the internal lenses should be cleaned
monthly.
To ensure a proper function of the gobo-wheel , we recommend lubrication in six month
intervals.The quantity of oil must not be excessive in order to avoid that oil runs out when
the gobo-wheel rotates.
There are no serviceable parts inside the device except for the lamp and the fuse.Please refer
to the instructions under "Fitting/Exchanging the lamp".Maintenance and service
operations are only to be carriedout by authorized dealers.
If the lamp burns out, the fine-wire fuse of the device might fuse, too.Only replace the fuse
bya fuse of same typeand rating.Before replacing the fuse, unplug mains lead.
1) Unscrew the fuseholder on the rear panel of the base with a fitting screwdriver from the
housing (anti- clockwise).
2) Remove the oldfuse from the fuseholder.
3) Install the new fuse in the fuseholder.
4) Replace the fuseholder in the housingand fix it.
DANGER :Disconnect from the mains before startinganymaintenance work
Replacing the fuse
Procedure:
-16-