SilverStar MX-COLOR User manual

USER MANUAL
MX-COLOR
LED110
Version 1.0
WWW.YAGANG.COM

PART 1 PRODUCT (GENERAL)..............................................................1
1.1--PRODUCT INTRODUCTION....................................................................................... 2
1.2--PRODUCT FEATURES...............................................................................................2
1.3--TECHNICAL SPECIFICATIONS...................................................................................3
1.4--PHOTOMETRIC DATA................................................................................................4
1.5--SAFETY WARNING....................................................................................................4
PART 2 INSTALLATION.........................................................................5
2.1--MOUNTING................................................................................................................6
2.2-- SETTINGUP (STAND ALONE)....................................................................................7
2.3--SETTING UP (MASTER/SLAVE)..................................................................................7
2.4--SETTING UP(DMX512 CONTROLLER).......................................................................8
PART 3 DISPLAY PANEL OPERATION................................................... 9
3.1--BASIC......................................................................................................................10
3.2--MENU......................................................................................................................11
3.3--SETTING DMX512ADDRESS...................................................................................12
3.4--RUN MODE.............................................................................................................12
3.5--EDIT PROGRAM......................................................................................................13
3.6--SPECIAL OPTIONS..................................................................................................14
PART 4 OPERATION WITH DMX512.....................................................15
4.1--BASIC ADDRESSING...............................................................................................16
4.2--CHANNEL ASSIGNMENT..........................................................................................16
4.3--FUNCTION EXPLANATION.......................................................................................18

Part 1
Part 1
1.1 PRODUCT INTRODUCTION
1.2 PRODUCT FEATURES
1.3 TECHNICAL SPECIFICATIONS
1.4 PHOTOMETRIC DATA
1.5 SAFETY WARNING
PRODUCT (GENERAL)
1

This product is designed for indoor use only. Suitable applications include wash or effect
lighting for architectural, stage or nightclub applications. Direct input of DMX512 signal
allows the fixtures to be controlled from any DMX512 controller. The fixture is fully
programmable with one custom program available and is supplied with two automatic
programs and two music-active programs (all accessible from DMX512 controller). This
product can beoperated as a single unit or with multiple unitsfor large applications.
1.1 PRODUCT INTRODUCTION
RGB Dimmer 0-100%
Strobe
Automatic programs
Music-active programs
Custom program (programmable)
Auto-color sequence (variable speed)
LCD display
Fan speed control
DirectDMX512 input
1.2 PRODUCT FEATURES
1
2
3
4
5
6
789
10
11
12
13
14
DMX OUT
DMX IN
110V~230V
POWER IN PUT
POWER
MIC
MODE UP DOWN ENTER
PRODUCT (GENERAL) 22006.11.15
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ITEM
Arm
Head
Base
Power selector switch
DMX OUT
DMX IN
Power switch
Mic
LCD display
Enter
Down
Up
Mode
Power connector

115
250
359
300
135
135
15
540
90 102
43.78
149.25
94.25
278.5
PRODUCT (GENERAL) 32006.11.15
1.3 TECHNICAL SPECIFICATIONS
100~120V...50/60Hz 220~240V...50/60Hz50W
50W
18pcs (6 XRED / 6X GREEN /6 X BLUE)
1W
15 (30 Optional)
Forced air convection
356 x 300 x356mm
8.9Kg
Voltage
Rated Power
LED/Unit
Output/LED
LED Beam Angle
Cooling
Dimensions
Weight

1.5 SAFETY WARNING
IMPORTANT
ALWAYS READ THE USER MANUAL BEFORE OPERATION.
PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON THE
PRODUCT IS THE SAME AS THE MAINS POWER SUPPLY IN YOUR AREA.
This product must be installed by a qualified professional.
Always operate the equipment as described in the user manual.
A minimum distance of 0.5m must be maintained between the equipment and
combustible surface.
The product must always be placed in a well ventilated area.
Always make sure that the equipment is installed securely.
DO NOT stand close to the equipment and stare directly into the LED light
source.
Always disconnect the power supply before attempting and maintenance.
Always make sure that the supporting structure is solid and can support the
combined weight ofthe products.
The earth wire must always be connected to the ground.
Do not touchthe power cables if your hands are wet.
ATTENTION
This product leftthe place of manufacture in perfect condition. In orderto
maintain this condition and for safe operation, the user must always follow the
instructions and safety warnings described in this user manual.
Avoid shaking or strong impacts to any part of the equipment.
Make sure thatal parts of the equipment are kept clean andfree of dust.
Always make sure that the power connections are connected correct and
secure.
If there is any malfunction of the equipment, contact your distributor
immediately.
When transferring the product, it is advisable to use the original packaging in
which the productleft the factory.
Shields, lenses orultraviolet screens shall be changed ifthey have become
damaged to such an extent that their effectiveness is impaired.
The lamp (LED) shall be changed if it has become damaged or thermally
deformed.
PRODUCT (GENERAL) 42006.11.15
GREEN
1
2
3
0
1
2
3
2468
10 Diameter(m)
515 130 62 31 25 LUX
15
BLUE
1
2
3
0
1
2
3
2468
10 Diameter(m)
600 150 70 34 30 LUX
15
RED
1
2
3
0
1
2
3
2468
10 Diameter(m)
645 170 72 50 40 LUX
15
WHITE
1
2
3
0
1
2
3
2468
10 Diameter(m)
1500 370 170 93 80 LUX
15
RGB 100%
1
2
3
0
1
2
3
2468
10 Diameter(m)
1600 430 180 95 90 LUX
15
1.4 PHOTOMETRIC DATA

Part 2
Part 2
2.1 MOUNTING
2.2 SETTING UP (STAND ALONE)
2.3 SETTING UP (MASTER/SLAVE)
2.4 SETTING UP (DMX512 CONTROLLER)
INSTALLATION
5

The LED fixture can be operated in any position at any angle. When mounted on a flat
surface, the surface must be strong enough to support 10 times the weight of the fixture and
stable so that the will be no damage caused to the fixture or surrounding people or objects
because of movements of the fixture on the surface.
When the unit is mounted in a hanging position, the fixture is attached using the mounting
brackets and a standard truss clamp or other clamping device. The mounting brackets
supplied are mounted using quick-release locks allowing simple mounting or removal.
2.1 MOUNTING
IMPORTANT SAFETY NOTE!!
Always use asafety cable when installing this unit!!
Be sure that the safety cable is connected to a solid load-bearing structure.
INSTALLATION 62006.11.15
Quick-release lock
Safety cable

INSTALLATION 72006.11.15
2.2 SETTING UP (STAND ALONE)
The LED fixture can be used as a stand alone unit. The stand alone functions AUTO 1,
AUTO 2, SOUND 1, SOUND 2, CUSTOM 1 can be activated without the need to connect to
any controller orconnecting to any other equipment.
Simply, access the <RUN> menu from the DISPLAY and select the target program to
activate.
When units are connected in series using DMX512 signal cable connect the units as shown
in the diagram below
Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin
connector of the first (MASTER) fixture.
Connect the end of the cable coming from the MASTER fixture which will have a (female) 3
pin connector to the input connector of the next fixture consisting of a (male) 3 pin
connector.
Then proceed to connect from the output asstated above to the input ofthe following fixture
and so on.
Set the first unit in the series to one of the STAND ALONE modes as described in section
2.2
All other units in the series should be set to <SLAVE> from the <RUN> menu.
2.3 SETTING UP (MASTER/SLAVE)
MASTER SLAVE SLAVE

When units are connected in series to a DMX512 controller and other DMX512 equipment,
connect the equipment as shown in the diagram below.
Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin
connector of the controller.
Connect the end of the cable coming from the controller which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector.
Then proceed to connect from the output as stated above to the input of the following fixture
and so on.
2.4 SETTING UP (DMX512 CONTROLLER)
INSTALLATION 82006.11.15
DMX512
CONTROLLER

Part 3
Part 3
DISPLAY PANEL OPERATION
3.1 BASIC
3.2 MENU
3.3 SETTING DMX512 ADDRESS
3.4 RUN MODE
3.5 EDIT PROGRAM
3.6 SPECIAL OPTIONS
9

3.1 BASIC
The LED fixtureis mounted with a LCD display and 4 controlbuttons.
DISPLAY PANEL OPERATION 10 2006.11.15
MODE UP DOWN ENTER
Scroll through the main menu or exit from the current sub-menu
Scroll 'UP' through the menu list or increase the value of the current function
Scroll 'DOWN' through the menu list or decrease the value of the current function
Enter the currently selected menu or confirm the current function value

DISPLAY PANEL OPERATION 11 2006.11.15
3.2 MENU
Welcome Run Auto 1
Auto 2
Sound 1
Sound 2
Custom
DMX
Slave
Edit Prg Edit Program
Step 0 100 Pan 0 2 55
Titl 0 255
Red 0 255
Green 0 255
Blue 0 255
Strobe 0 255
Time 0 8
Fade 0 8
Reset Custom Confirm Reset
Option Fan Speed
Invert Pan
Invert Tilt
Reset
Load Default
Low
High
ON/OFF
ON/OFF
Address 1 499

Welcome Run Auto 1
Auto 2
Sound 1
Sound 2
Custom
DMX
Slave
3.3 SETTING DMX512 ADDRESS
Address
Enter the Address mode to set the DMX address
3.4 RUN MODE
Run
Enter the Run menu in orderto select the operation modeof the fixture
For stand alone operation, select from the modes AUTO 1 , AUTO 2 ,
SOUND 1 , SOUND 2 & CUSTOM
For control witha DMX512 controller select DMX
Toset a unit as a slave select Slave
DISPLAY PANEL OPERATION 12 2006.11.15
Welcome Address 1 499

3.5 EDIT PROGRAM
Step
Select from 100 steps to create or edit
Steps that are not required should have the Time set as 0
Pan
Set the PAN position of the LED fixture (0-255)
Tilt
Set the TILT position of the LED fixture (0-255)
Red , Green & Blue
Combine RED, GREEN & BLUE to create an infinite range of colors (0-255)
Strobe
Select the strobe speed from 0-24Hz
Time
Set the Time for the current step (0-8)
The unit of Time is 1 seconds
Fade
Set the [Fade] time of the current step (0-8)
The unit of [Fade time is 1 second
Reset Custom
Enter Reset Custom in order to reset all settings in the CUSTOM mode
Edit Prg Edit Program
Step 0 100 Pan 0 2 55
Titl 0 255
Red 0 255
Green 0 255
Blue 0 255
Strobe 0 255
Time 0 8
Fade 0 8
Reset Custom Confirm Reset
Welcome
DISPLAY PANEL OPERATION 13 2006.11.15

DISPLAY PANEL OPERATION 14 2006.11.15
3.6 SETTING DMX512 ADDRESS
Fan Speed
Set the Fan Speed as high or low
Note that whenthe fan speed is set to low that any overheating by the
unit will automatically change thefan speed tohigh
Invert Pan
Select On] in order to invert the PAN values
Invert Tilt
Select On in order to invert the TILT values
Reset
Select Reset to reset the fixture
Load Default
Select Load Default to reset all settings in the fixture
(does not include CUSTOM mode)
Welcome Option Fan Speed
Invert Pan
Invert Tilt
Reset
Load Default
Low
High
ON/OFF
ON/OFF

Part 4
Part 4
OPERATION WITH DMX512
4.1 BASIC ADDRESSING
4.2 CHANNEL ASSIGNMENT
4.3 FUNCTION EXPLANATION
15

4.1 BASIC ADDRESSING
It connect all of the units in series using standard DMX512 signal cable
It set the DMX512 address in the 'Address' menu
It is possible to have the same DMX address or independent addresses for each fixture.
4.2 CHANNEL ASSIGNMENT
1
2
3
4
5
6
7
8
9
10
PAN
TILT
PAN/TILTSPEED
RED
GREEN
BLUE /AUTO-MACRO SPEED
RGB MACRO,AUTO-MACRO & WHITE
DIMMER
STROBE
CONTROL MODE
CHANNEL FUNCTION
CH1 Function
%
255
0
100
0.0
540
OPERATION WITH DMX512 16 2006.11.15
CH2 Function
%
255
0
100
0.0
270 FAST
SLOW
CH3 Function
%
255
0
100
0.0
CH4 Function
%
255
0
100
0.0
RED
OFF
CH5 Function
%
255
0
100
0.0
GREEN
OFF
BLUE FAST
OFF SLOW
CH6 Function
%
255
0
100
0.0

CH7 Function
%
WHITE
AUTO-MACRO
RED UP/GREEN DOWN /BLUE 100%
RED 100%/GREEN UP/BLUE UP
RED 100%/GREEN 0%/BLUE DOWN
RED DOWN/GREEN 0%/BLUE 100%
RED 0%/GREEN DOWN/BLUE 100%
RED 0%/GREEN 100%/BLUE UP
RED DOWN /GREEN 100%/BLUE 0%
RED 100% /GREEN UP / BLUE 0%
NO FUNCTION
251 255
241 250
216 240
186 215
156 185
126 155
96 125
66 95
36 65
635
0 5
98.5 100
94.5 98
84.5 94
73 84
61 72.5
49.5 60.5
37.5 49
26 37
14 25.5
2.5 13.5
02
CH10 Function
%
CUSTOM (AFTER 3SECONDS)
SOUND 2 (AFTER3 SECONDS)
SOUND 1 (AFTER3 SECONDS)
AUTO 2 (AFTER3 SECONDS)
AUTO 1 (AFTER3 SECONDS)
RESET (AFTER 3SECONDS)
NORMAL OPERATION
216 255
176 215
136 175
96 135
56 95
46 55
045
84.5 255
69 84
53.5 68.5
37.5 53
22 37
18 2 1.5
0 17.5
OPERATION WITH DMX512 17 2006.11.15
MAXIMUM
INTENSITY
MINIMUM
INTENSITY
CH8 Function
%
255
0
100
0.0
24Hz
NO FUNCTION
CH9 Function
%
255
0
100
0.0

4.3 FUNCTION EXPLANATION
PAN
CH1 adjusts the PAN from 0 to 540
TILT
CH2 adjusts the TILT from 0 to 540
PAN/TILT SPEED
CH3 adjusts thespeed of the PAN and TILT faders
RED, GREEN & BLUE
CH4, CH5 &CH6 control the intensity of each of the RED,GREEN & BLUELEDs.
When the slider is at the highest position (255) the intensity of the color is the
maximum
CH4, CH5 &CH6 can be combined together to create over 16million colors.
COLOR MACRO & WHITE
The COLOR MACRO allows theuser to select from a linear range of colors
The range from 241-250 isan AUTO-MACRO.
When theAUTO-MACRO is selected, CH6 controls the speed of the AUTO-MACRO.
When the slideris at the top of the slider the coloris WHITE
DIMMER
CH8 is an overall DIMMER for the currently selected / created color
STROBE
CH9 is the strobe channel and controls the speed of the strobe.
The strobe is with an adjustable speed with a maximum of 24Hz
CONTROL MODE
CH10 allows theuser to access the internal programs in the fixture
CH10 also allowsthe unit to perform a reset.
Note that all functions from CH10 require a 3 second delay before activation.
OPERATION WITH DMX512 18 2006.11.15