SilverStar LT-VIII User manual

1
LT - VIII
LASER MOTORHEAD LIGHT
USER MANUAL
Please read over this manual before operation the light

2
Open box to check
Installation
¾
¾
¾
¾
¾
¾
¾
¾
¾
This product use new hi
g
h temperature-resistance pro
j
ect plastic to
make. It has a beautiful surface to show the characteristic of new sta
g
e
li
g
hts. You could choose the color
y
ou like. It is made accord CE
standard. It accord with the international DMX512 a
g
reement. Sin
g
le or
several can be used at same time. It could be used in different place.
The product use semiconductor laser movin
g
mirror scan to make man
y
kinds of
g
obos and the size of
g
obos ad
j
ustable. Li
g
ht touch control
switch and code displa
y
make operation easier. When
y
ou receive the
product, take it gently check if there is problem which cause in
transportation. At the same time please pa
y
attention to see if there are
some parts enclosed:
1 Power line
1 Fuse line
1 User manual
Please confirm whether the volta
g
e
y
ou have is same as si
g
ned on the
light before install.
Installed by technician. It muse be placed safety and best light angle.
Must keep space between li
g
ht equipments and combustibles more than
half a meter. Keep space between li
g
ht equipments and wall more than
0.15 meter.
The fans and vent-pipes should not be
j
ammed b
y
other equipment and
decorate materials.
There have a fuse line connection hole at the bottom of li
g
ht. Please use
a fuse line that could stand 10 double of li
g
ht's wei
g
ht to drill throu
g
h
fuse line connection hole to help install in safety view.
The light must be fixture installed.
In safety view please put ground wire into the ground.
Laser Motorhead Li
g
ht .1.

3
Attention
Instruction & Function
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
Please do not open the bottom cover yourself without permission.
Operate it accord the user manual. Please call the technician in case the
machine broken down.
Do not use it under the damp and rain.
Pay attention to prevent the light from strong bump.
Prevent the dust into the product
Keep the vent-pipe well while working.
Keep the plug insert well before put into power.
Don't look the light directly to prevent make some destroy with
eyes.Don't light or extinguish frequently, otherwise the life span of the
light tube will be shortened.
In view of the special characters, after operated the light an hour the
product shall be paused about 15 minutes before be used next time.
Don't touch the product and draw the power line if you hand wet.
Keep the space between light equipments and the lighted things more
than one meter.
Don't open the cover for there have no parts the user can repair.
Don't operate the light without lamps.
If the semiconductor laser doesn't as light as before or there have some
destroy with lens or other parts, please contact the distributor in time.
When you want to retransfer the products, you'd better use the original
package to shockproof.
The product use international standard DMX512 signal to control.
Through use light touch switch and code show screen you can easy to
set DMX channel and function operate.
: security on/off key switch
After turn on, code show screen will show the DMX channel (once you
set the DMX channel and store them it will show you latest setting
value).
ON/OFF SECURITY KEY SWITCH
Laser Motorhead Light .2.

4
¾
¾
¾
¾
¾
¾
DMX channel setting way:
1. Press up or down key to change the channel address of show.
2. Press enter key to confirm the change. The green light will shine to
indicate the light already store the channel address.
3. The product will show the latest setting value when you operate next
time.
The product can operate by single mode without controller.
Press fung key continuous, the code screen will show the function operate
code of products in proper order. Every function operate code
corresponding special function as following:
After the code screen show the function operate code, if you press up
or down the code screen will show N (NO) or Y (YES).
You can press enter to confirm when the function operate code screen
show Y . At the same time the green light will shine and the product
will make this function setting effect and store. When the function
operate code screen show N , you also can press enter to make this
function setting out of effect and store.
Set light at sound active station. The light auto-black out without sound
active music input.
The product has 8 operate channel and use international standard
DMX512. The details as following:
Single Machine Mode
Controller Operate Mode
Laser Motorhead Light .3.
Function Code Parallelism Function
001 DMX control
002 Sound control
003 Auto-procedure
004 Subordinate operate
005 Address code set
007 Reset, on or off
008 00B
… Keep
Sound active auto speed (set)

5
¾
¾
¾
Connect the XLR-XLR control line from the DMX output of
controller to DMX input of each product and connect the DMX output
of the first one to the DMX input of the second one. Connect all
products in this wa
y
. Then use the attached circle plu
g
to connect the
signal output of last machine like picture show:
N
ote: Please remember the si
g
nal output of last machine must connect
the attached circle plu
g
. The circle plu
g
connect a 120 resistance
between 2 feet and 3 feet canon plug. The signal reflects phenomena
can be avoided by using circle plug during DMX 512 signal transfer.
The product use 3 feet XLR plu
g
. If the controller
y
ou use is 5 feet
XLR plu
g
,
y
ou must use a interchan
g
e line from 5 feet to 3 feet as
following picture:
Ω
7
picture size
8
reset
6
picture roll
5
4
2
Y line
3
picture
1
X line
Channel
0-255
0-255
0-255
0-255
0-255
0-255
0-255
0-255
bigger or smaller from the center
(0-biggest, 255-smallest)
0-127 open light, 128-254 black out,
255 reset.
roll around the center (0-360 )
roll Y line like mirror image
compress fold
roll X line like mirror image
compress fold
0-265 (vertical)
12 pictures, average DMX value
(Can change accord user require)
0-370 (horizontal)
function
DMXIN DMXOUT POWER IN FUSE F6.3A DMXIN DMXOUT POWER IN FUSE F6.3ADMXIN DMXOUT POWER IN FUSE F6.3A
Light 1
Control singal input
Output and input connect together Output and input connect together
Lignt NLight 2
Laser Motorhead Light .4.

6
¾
¾
¾
¾
¾
¾
When it controlled by DMX512, you must installADDR on the light. One
lighthas8channels.PleaseInstall itasfollows:
Calculateaddressnumber: calculateformula: ADDR=8 N-8
Example: No.1 light ADDR=0; No.2 light ADDR=8;
No.3 light ADDR=16; No.4 light ADDR=24;
Don't connect an
y
lines to DMX input entrance. DMX channel can be
set freely. The products will be used as a principal one.
Set begin channel of other lights to be 004 and used as subordinate
machine.
Connect the XLR-XLR control line from the DMX output of principal
machine to DMX input of each subordinate product and connect the
DMX output of the first one to the DMX input of the second one.
Connect all products in this wa
y
. Then use the attached circle plu
g
to
connect the signal output of last machine.
Under the principal/subordinate in same step control mode
y
ou can use
b
uilt-in auto procedure of principal machine or use built-in MIC sound to
control. Subordinate machines can work with principal one in same step.
×
Principal/subordinate same step control mode
Laser Motorhead Light .5.
5Pins canon( )plug
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pins canon(socket)
5Pins canon(socket)
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pin 4: N/C
Pin 5: N/C
3plug
Pin 1: GND(SCREEN)
Pin 2: Signal(-)
Pin 3: Signal(+)
Pins canon( )
The transform of the controller line of 3 pins and 5 pins (plug and socket)
Pin 1: Screen
Pin 2: Signal -
Pin 3: Signal +
3 pins canon connect to the input of DMX512 connection

7
Laser Motorhead Light .6.
Usage of our DMX512-KT console
¾
¾
Our company recommend use our DMX512-KT console to control our
Scanning Computer Light. select 17 MARTIN 518.
Set the address code as following chart:
Projector No. & chanees. 1 2 4 8 16 32 64 128 256 512
Projector 4 - chanees.42-55
Projector 5 - chanees.56-69
Projector 6 - chanees.70-83
Projector 7 - chanees.84-97
Projector 8 - chanees.98-111
Projector 9 - chanees.112-125
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
ON
ON
OFF
OFF
ON
ON
OFF
OFF
ON
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Projector 10 - chanees.126-139
Projector 11 - chanees.140-153
Projector 12 - chanees.154-167
OFF
OFF
OFF
ON
OFF
ON
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
Projector 3 - chanees.28-41OFF OFF ON ON ON OFF OFF OFF OFF OFF
Projector 1 - chanees.0-13
Projector 2 - chanees.14-27
OFF
OFF
OFF
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
Specification
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
¾
Voltage: AC220V~240V, 50/60Hz
Rated power: 60W
Laser: semiconductor laser, output 60mW
Laser wavelength: 532nm
Insulation resistance:>2M
Channel: 8 channels
Signal: DMX512
Control mode: controller, single machine mode, principal /subordinate
work at same step.
Design: many kinds of effects through moving mirror.
Strobe: 0-6 times/SEC, adjustable
Scan: horizontal: 370 , vertical: 265
Size: 370 275 375mm
Net weight: 9.5kg
Ω
××
O O

8
Laser Motorhead Light .7.
Maintain
Announcement
¾
¾
¾
The optical lens and illuminators must clean regular to protect a better
effect. You can clean them accord the light's operate times and the
using situation. Use soft cloth and original glass cleaner to clean. You'd
b
etter clean exterior optical system every 20 days and inside optical
system every 60 days at least.
Do not use organic solvent such as alcohol to clean the cover of light.
When we delivery the goods out of factory, it's function is good and
package is well. All users must obey all noted attentions and operate
rules. We won't serve free of charge repair if the destroy be caused by
your own wrong operate. All the problems which be caused by not
operate accord the user manual also not the duty of distributor.
We won't inform again if there have any more changes of user manual.