SilverStone GEMINI Series User manual

Gemini 800C Platinum
Gemini Series
80 Plus Platinum 800W 2U CRPS
Redundant Power Supply
800W+800W 24hour and well working performance at 45°C fully continuous power output
2U CRPS form factor: 82mm (W) x 102mm (H) x 245mm (D)
80 Plus Platinum certification
Active PFC (full range)
All Japanese electrolytic capacitors
Hot swappable design

SPECIFICATION
SilverStone Gemini Series
Gemini 800C Platinum
SST-GM800C-PF/SST-GM800C-PFU
1+1 2U CRPS Redundant Switching Power Supply
80 PLUS Platinum efficiency certified.
800W+800W
01
1.0 Introduction
2.0 Input Power
This specification defines the electrical and functional characteristics for two
800W Power modules .Unless otherwise noted, the requirements in this specifi-
cation are applicable for each of the above listed power supplies.
The 800W power supply modules will be used for 1+1 redundant (load sharing)
operation and should be designed to be inserted and removed ("hot plugging")
while the system is running.
The power supply must provide a PMBus interface through which the system is
able to read and write various devices. Note that, with 2 power supplies present
in a system (redundant configuration), the I2C devices with-in a power supply
must be accessible even if the power supply has failed or faulted.
2.1 Voltage and Current
Input voltage
Input current
Parameter Minimum Nominal Maximum
Low Line 90Vrms 100-127Vrms 140Vrms
High Line 180Vrms 200-240Vrms 264Vrms
Frequency 47 Hz 50/60 Hz 63 Hz
Parameter Maximum Input Current
100-127Vac Input 10A
200-240Vac Input 5A

2.2 Efficiency
3.1 Voltage and Current
3.2 Ripple and Noise
※1. At 264Vac 25
°C , max load cold start, any Inrush current spike shall not
exceed 35A peak.
※2. At 90~264Vac 25 °C , max load hot start, any inrush current of the AC line
shall not cause damage to the power supply.
Output voltage and current
※1. Maximum combined power on +3.3V and +5V shall not exceed 170W.
※2. Maximum combined power for all output shall not exceed 800W.
3.0 Output Power
02
Only power module efficiency meet Cybenetics Platinum at all specified load
points. The efficiency should be measured at 230VAC and with external fan
power according to Climate efficiency measurement specifications.
2.3 Power Factor
The power factor of the power supply should greater than 0.95 at 115Vac/60Hz
input voltage and 50% of maximum load.
The maximum allowed ripple and noise output of the power supply is defined in
below table. This is measured over a bandwidth of 10Hz to 20MHz at the power
supply output connectors. A 10uF low ESR electrolytic capacitor in parallel with
a 0.1uF ceramic capacitor is placed at the point of measurement. To help
reduce switching ripple further, an additional 2200uF low ESR electrolytic
capacitor may be placed in parallel.
Measurements made where the cable connectors attach to the load.
2.4 Harmonic Current
The harmonic current of the power supply shall be measured at the maximum
load with input voltage of 230Vac/50Hz. Meet EN 61000-3-2, Class A.
Voltage +3.3V +5V +12V -12V +5Vsb
Maximum load 25A 25A 65A 0.8A 3.5A
Minimum load 1A 1A 1A 0A 0.1A
Max. power 170W *1780W 9.6W 17.5W
Total power 800W*2
Regulation limit ±5% ±5% ±5% ±10% ±5%
Output +5V +3.3V +12V -12V +5Vsb
Ripple & Noise 50mVp-p 50mVp-p 120mVp-p 120mVp-p 50mVp-p

03
3.3 Dynamic Loads
3.4 Hot Swap Transient Load
The output voltages shall remain within limits specified for the step loading
and capacitive loading specified in the test table below. The load transient
repetition rate shall be tested between 50Hz and 5KHz frequency and above
25% load.
When an additional power module is ORed together, or, removed from a
group of one power module, the outputs shall maintain regulation.
3.5 Turn On/Off Overshoot
Overshoot at turn on shall be less than 10% of the nominal output voltage.
3.6 Load Capacitance
The power supply shall be stable and meet all requirements with the follow-
ing capacitive loading ranges.
Output Step load Load slew rate Capacitive load
+12V 60% of max load 0.5A/us 18000uF
+5V 30% of max load 0.5A/us 5000uF
+3.3V 30% of max load 0.5A/us 5000uF
+5Vsb 50% of max load 0.5A/us 350uF

04
Output Min. Max.
+12V 500uF 18000uF
+5V 400uF 5000uF
+3.3V 250uF 5000uF
-12V 1uF 350uF
+5Vsb 20uF 350uF
4.0 Protection
4.1 Shutdown Definition
4.2 Over Current Protection
4.3 Over Voltage Protection
If the power supply is protected when OCP, OVP, OTP or short protection
(except
+5Vsb), the power supply shall shut down and latch off. The power supply
return to normal operation after the fault condition has been remove and
PS_ON signal must reset for OFF/ON cycle with a minimum OFF time of 1
second or AC power must reset for OFF/ON cycle with a minimum OFF time
more than 1 minute. Then it will turn on again.
+5Vsb by output protection shall be auto recovery.
Shutdown is defined as a condition where the +12V, +5V, +3.3V and -12V
outputs latches off. The +5Vsb output shall remain on.
The overload currents testing slew rate is 10 A/s starting from maximum
load.
The over voltage sense circuitry and reference shall reside in packages that
are separate and distinct from the regulator control circuitry and reference.
The power supply shall provide latch off mode for over voltage protection
as defined in below.
Output Over current limit Protection type
+5V 27.5A~37.5A Latch off
+3.3V 27.5A~37.5A Latch off
+12V <91A Latch off
+5Vsb <9A Auto recovery
Output Over voltage threshold Protection type
+5V 5.6V~6.5V Latch off
+3.3V 3.8V~4.5V Latch off
+12V 13.2V~15.6V Latch off

05
4.4 Short Circuit Protection
An output short circuit is defined as any output impedance of less than 10m
Ω. The power supply shall shut down and latch off for shorting the +3.3V,
+5V, or +12V rails to return.
The +5Vsb power supply will not latch under short circuit condition on
+5Vsb output. It will return to its normal operating mode once the short
circuit is removed.
4.5 Over Temperature Protection
The power supply shall have thermal protection against over temperature
condition caused by loss of airflow or excessive ambient or hot spot
temperature. The PSU should shut down and latch off when over tempera-
ture triggered.
4.6 Fan Fault Protection
After 10 sec the power supply should be latch off when fan fault occur.
When fan speed malfunction, fan warning signal should be sent it out first
then latch off the power supply.
4.7 Backplane Buzzer Alarm
4.8 LED Indicator
When power supply operate at 1+1 redundant mod, if any one of power
supplies fails, the buzzer should make a continuous sound.
All LEDs shall protrude beyond the supply chassis surface for good visibili-
ty. There is a bi-color LED.
4.7.1 Two Ways to Stop the Buzzer Sound
1. Remove the damaged power.
2. Press the push switch.
Power Supply Condition LEDs State
No AC power OFF
Only standby output on Blink green
Power supply outputs ON and OK Green
Power supply failure Amber or Blink green

5.1 Hold-up Time
06
5.0 Sequencing and Signals
T1: +5Vsb power on delay time ≦1.5s.
T2: The output voltages rise time from 10% to 90% during 0.1ms to 70ms.
T3: PWOK signal delay time during 100ms to 500ms.
T4: AC loss to PWOK signal hold up time ≧10ms.
T5: PWOK signal turn off delay time ≧1ms.
T6: Power on delay time ≦400ms.
T7: AC loss to +5Vsb output hold up time ≧50ms.
Outputs
+12V, +5V, +3.3V T4: 10ms MIN
12ms MIN
T7: 50ms MIN
T3: 100ms～500ms
PS ON
PWOK
T5: 1ms MIN
T5: 1ms MIN
AC ON
T2: 0.1～70ms
+5Vsb
T6: 400ms MAX
T1: 1.5S MAX
T2: 0.1～70ms
When AC is removed, the output must remain regulation for at least 12ms
with 70% of maximum load and over 100-240VAC input.
5.2 PWOK Signal
PWOK is an active high output signal from the power supply used to
indicate that:
1.The PS ON signal is active low
2.The +12V, +5V and +3.3V outputs is above its under voltage threshold
and below its over voltage threshold
3.The load is below the over current threshold
4.The power supply is operating normally and within thermal limits.
If the PWOK signal transitions from high to low (de-asserted) shows the
power supply shut down.

07
5.4 Power on Delay Time
5.3 PS ON Signal on/off Control
5.5 Rise time
5.6 Serial Bus Interface
The electrical and timing characteristics of the PWOK signal are given in below.
Signal type +5V TTL compatible
Logic level low ＜0.4V while sinking 4 mA
Logic level high Between 2.4V and 5.25V output while sourcing
200 uA
High state output impedance 1KΩ
PWOK delay time 100ms ＜T3 ＜500ms
AC loss to PWOK hold up time T4 ≧ 10ms
PWOK turn off delay time T5 ≧ 1ms
5. For test purposes, the PWOK signal shall be terminated at the output
power supply connector with a 0.01uF ceramic capacitor.
6. When only one power module, the AC loss to PWOK hold up time ≧
10ms at 70% load condition.
PS ON is an active-low, TTL-compatible signal that allows a motherboard
to remotely control the power supply in conjunction with features such as
soft on/off. The OFF/ON cycle with a minimum OFF time is 1s.
The power supply shall provide an internal pull-up to TTL high. The power
supply shall also provide de-bounce circuitry on PS ON to prevent it from
oscillating on/off at startup when activated by a mechanical switch.
The power-on time is defined as the time from when PS ON is pulled low to
when the +12V, +5V and +3.3V outputs are within the regulation ranges
specified in Section 3.1. The power-on time shall be less than 400ms.
The output voltages shall rise from 10% to 90% of nominal to within the
regulation ranges specified in Section 3.1 within 0.1ms to 70ms.
The system will utilize PMBus for communication between itself and the
power supply. The bus is to be compatible with both SMBus 2.0‘high power’
and I2C. The bus will be 3.3V. A voltage shifting circuit may be needed to
accomplish this. Except where specifically called out, there will be no
pull-ups in the power supply. The pull-ups will be provided external to the
power supply via 4.7K~10Kohm in the host system.
Signal Minimum Maximum
VIL, Input Low Voltage 0V 0.8V
IIL, Input Low Current (Vin = 0.4 V) - -1.6mA
VIH, Input High Voltage 2.0V 5.25V

5.6.1 Address (ADDR)
5.6.2 SCL and SDA
08
The PMbus device address locations are shown below.
PSU PMBUS Address FRU Address
Binary Hex Binary Hex
PSU1 1011 0000 B0 1010 0000 A0
PSU2 1011 0010 B2 1010 0010 A2
SCL and SDA comprise a bi-directional serial data bus used to commu-
nicate between the SMBus devices with-in the power supply and the
host system.
The host system has pull-ups on these signals; the power supply must
not.
The power supply may be used in a system with up to one additional, redun-
dant, power supplies. The load is shared between the power supplies that are
ORed together. When two supplies are ORed together, they may be used in
1+1 configuration.
7.1.1 UL/cUL UL62368-1, 3rd Edition
7.1.2 TUV EN62368-1, 3rd Edition
7.1.3 CB IEC62368-1, 3rd Edition
.
6.0 Redundant Operation
7.0 SAFETY AND EMS REQUIREMENTS
7.1 Safety requirments
EN55032 / EN55035 requirements
7.2 EMC requirements
7.2.1.1 Meet FCC part 15 class A.
7.2.1.2 Meet EN55032 class A.
7.2.1 EMI Requirements

09
Meet IEC61000-4-2 level 4, Criteria A for contact +/- 8KV and air
+/-15KV.
7.2.2 Electrostatic Discharge Immunity Test (ESD)
Meet IEC61000-4-3 level 3, Criteria A for 80~1000MHz, 10V/m.
7.2.3 Radio Frequency Electromagnetic Field Immunity Test (RS)
Meet IEC61000-4-4 level 3, Criteria A for L to N 2KV
7.2.4 Electrical Fast Transient/Burst Immunity Test (EFT/BURST)
Meet IEC61000-4-5 level 3, L to N 1KV, line to Earth 2KV, Criteria A.
7.2.5 Surge Immunity Test
Meet IEC61000-4-6 level 3, Criterion A for 0.15~80MHz, 10V/m.
7.2.6 Conducted Disturbances Induced by Radio-Frequency Field
Immunity Test
Meet IEC61000-4-8 level 3, Criterion A for 50Hz, 10A/m.
7.2.7 Power Frequency Magnetic Field Immunity Test
Meet IEC61000-4-11
Criterion B for 0% residual 0.5 cycle at 50Hz.
Criterion C for 70% residual 25/30 cycles at 50Hz/60Hz.
Criterion C for 0% residual 250/300 cycles at 50Hz/60Hz.
7.2.8 Voltage Dips and Voltage Interruptions Immunity Test
Meet EN 61000-3-2 Class A.
7.2.9 Suppression of Harmonics Test
Meet EN 61000-3-3
7.2.10 Voltage Fluctuations Test
Each unit must pass a 1.8KV (AC) between line and ground (FG)
hi-pot test for a minimum of 3 second without failure, current limit
10mA.
7.2.11 Dielectric Strength Test
AC input 264V/63Hz, touch current should not exceed 3.5mA.
7.2.12 Touch Current Test
Line to ground/chassis, input DC 500V,3 seconds >20MΩat 25
°C
and relative humidity 70% of reference.
7.2.13 Insulation Resistance Test

8.0 Environment
9.0 Reliability
8.1. Temperature
10
8.1.1 Operation temperature of the supply will be between 0 °C to 45 °C
8.1.2 Storage temperature of the supply will be -40 °C to +80 °C .
>300,000 Hours at 230Vac/50HZ maximum load 25℃condition. The
failure rate shall be calculated with Telcordia SR-332 issue 4.
8.2. Humidity
8.2.1 Operation relative humidity of the supply will be between 10% and
90% (non-condensing).
8.2.2 Storage relative humidity of the supply will be between 5% and 95%
(non-condensing).
9.1 MTBF
10.0 Dimension
The power supply dimension is 245mm (L) x 84.8mm (W) x 82mm (H).
(Refer to outline drawing)
9.2.1 Operating
2.94 , 10-500Hz, 10 minutes per cycle, 30 minutes for each X, Y
and Z axis.
9.2.2 Non-operating
5.88 , 10-500Hz, 10 minutes per cycle, 30 minutes for each X, Y
and Z axis.
9.2 Vibration
Non-operating (package)：20G, half sin-wave, each per axis.
9.3 Shock
8.3.1 The maximum operation altitude of the supply is 5000 meter.
(The ambient operating temperature decreases by 1°C for every
305m increase in altitude.)
8.3.2 The maximum storage altitude of the supply is 15000 meter.

11
11.0 Serial Bus Commands
This feature only the power module (TG17-0800-01) support
11.1 PMBus
Code Command Bytes Read / Write
01h Operation 1 Read / Write
03h Clear_Faults 0 Write
05h Page_Plus_Write Variable Block Write
06h Page_Plus_Read Variable Block Write – Block Read Process Call
19h Capability 1 Read
1Ah Query 1 Block Write – Block Read Process Call
1Bh SMBALERT_Mask 2 Block Write – Block Read Process Call
20h Vout_Mode 1 Read
30h Coefficients 5 Block Write – Block Read Process Call
78h Status_Byte 1 Read
79h Status_Word 2 Read
7Ah Status_Vout 1 Read
7Bh Status_Iout 1 Read
7Ch Status_Input 1 Read
7Dh Status_Temperature 1 Read
7Eh Status_CML 1 Read
81h Status_Fans 1 Read
86h Read_Ein 6 Block Read
87h Read_Eout 6 Block Read
88h Read_Vin 2 Read
89h Read_Iin 2 Read
8Bh Read_Vout 2 Read
8Ch Read_Iout 2 Read
8Dh Read_Temperature1 2 Read
8Eh Read_Temperature2 2 Read
8Fh Read_Temperature3 2 Read
90h Read_Fan speed 2 Read
96h Read_Pout 2 Read
97h Read_Pin 2 Read
98h PMBus_Revision 1 Read
The power supply will provide the following access via PMBus
protocol:
●Power supply status
●Input/output power metering
In the following sections, all operations, values and definitions are in
compliance with the PMBus specifications unless explicitly noted.
Only PMBus commands and bits explicitly identified in the tables
under Section 13.2 are supported. Therefore, any attempt to write
using these commands must be handled as unsupported.

12
11.2 PMBus Command Summary
PMBus commands are one byte command codes. As below listing is
power supply can support of PMBus commands.
11.2.1 Read commands
The READ commands allow the host to read temperature, current,
voltage, power and energy parameters of the power supply.
PMBus direct format set m = 01h, R = 00h, b = 00h.
PMBus command Description Data format
Read_Vin Returns the input voltage in voltage. Linear
Read_Iin Returns the input current in amperes. Linear
Read_Pin Returns the input power, in watts, of the
power supply. Linear
Read_Ein
Commands are used to return
information the host can use to calculate
the input power consumption of power
supply.
Direct
Read_Eout
Commands are used to return
information the host can use to calculate
the output power consumption of power
supply.
Direct
Read_Vout Returns the output voltage in voltage. Linear
Read_Iout Returns the output current in amperes. Linear
Read_Pout Returns the output power, in watts, of the
power supply. Linear
Read_Temperature_1 Returns the temperature in
°C of the
airflow inside temperature. Linear
Read_Temperature_2 Returns the temperature in
°C of the hot
spot temperature. Linear
Read_Temperature_3 Returns the temperature in
°C of the
Primary side hot spot temperature. Linear
Read_Fan speed Returns the fan speed in revolutions per
minute Linear

13
Accuracy
Accuracy
Pin < 100W Pin > 100W
Read_Vin ±5%
Read_Iin ±0.1A ±5%
Read_Pin ±10W ±5%
Read_Vout ±5%
Read_Iout ±0.5A ±5%
Read_Pout ±10W ±5%
Read_Temperature_1 ±5℃
Read_Temperature_2 ±5℃
Read_Temperature_3 ±5℃
Read_Fan speed <9000rpm±1000rpm; >9000rpm±2000rpm
11.2.2 Capability and inventory reporting
The follow commands shall be supported for discovery of the
power supplies capabilities.
11.2.3 PAGE_PLUS_WRITE
The PAGE_PLUS_WRITE command is used to set the page within a
device, send a command, and send the data for the command in one
packet.
11.2.4 PAGE_PLUS_READ
The PAGE_PLUS_READ command is used to set the page within a
device, send a command, and read the data returned by the command
in one packet.
Command Meaning Value
Capability
Packet Error Checking is supported
Maximum supported bus speed is
100KHz
Support the SMBus Alert Response
protocol
90h
Query Used to determine if the PSU supports a
specific command Byte
PMBus_Revision Used to verify the PMBus revision the
power supply is base on 22h

14
11.2.5 Coefficients
This command is used to retrieve the m, b and R coefficients needed by
data in the DIRECT format.
11.2.6 Status commands
Status information is binary. A value of 1 indicates a fault or warning
event has occurred and a value of 0 indicates that a fault or warning
event has not occurred.
When the power an exception occurs, will set the warning bit. Warning
bit will be automatically cleared when the anomalies remove.
The Status_Byte (78h) and Status_Word (79h) message content is
described as shown below.
Byte Bits Bit name Meaning
Low
7 Busy Not support, set to 0
6 OFF +12V output off set to 1
5 Vout_OV_Fault +12V output overvoltage fault has occurred
4 Iout_OC_Fault +12V output overcurrent fault has occurred
3 Vin_UV_Fault Input under voltage fault has occurred
2 Temperature A temperature fault or warning has occurred
1CML A communications, memory or logic fault has
occurred
0 None of above Not support, set to 0
High
7Vout +12V output voltage fault or warning has
occurred
6Iout +12V output current fault or warning has
occurred
5 Input An input voltage fault or warning has occurred
4 Not use Not support, set to 0
3 Power_Good# The PWOK signal, if present, is negated
2 Fans A fan or airflow fault or warning has occurred
1 Other Not support, set to 0
0 Not use Not support, set to 0

15
The Status_Vout (7Ah) command returns one data byte with contents as below:
The Status_Iout (7Bh) command returns one data byte with contents as below:
The Status_Input (7Ch) command returns one data byte with contents as below:
Notes:
1.Input voltage sense in front of PSU.
The Status_Temperature (7Dh) command returns one data byte with contents
as below:
Bits Meaning
7 +12V output voltage exceed 14V has occurred (Fault)
6 +12V output voltage exceed 13.2V has occurred (Warning)
5 +12V output voltage less than 10.8V has occurred (Warning)
4 +12V output voltage less than 10V has occurred (Fault)
3-0 Not support, set to 0
Bits Meaning
7 +12V output current exceed 75A has occurred (Fault)
6 Not support, set to 0
5 SMBaltert# low means Warring has occurred.
4-0 Not support, set to 0
Bits Meaning
7-6 Not support, set to 0
5 Input voltage less than 80±5Vrms1has occurred (Warning)
4 Input voltage less than 74±5Vrms1 has occurred (Fault)
3 Unit Off For Insufficient Input Voltage
2-0 Not support, set to 0
Bits Meaning
7
Fault setting:
Temperature (The power supply into the airflow inside) exceed 66
±4
°C or Secondary hot spot exceed 115 ±5 °C or Primary side hot
spot exceed 115±5
°C
Recover setting:
Temperature less than 55 ±5
°C and Secondary hot spot less than
70 ±5
°C and Primary side hot spot less than 70±5 °C
6
Temperature (The power supply into the airflow inside) exceed 62
±4
°C (Warning) or Primary/Secondary side hot spot exceed 110±5
°C (Warning)
5-4 Not support, set to 0
3-0 Reserved, read 0

16
The Status_CML (7Eh) command returns one data byte with contents as below:
The Status_Fans (81h) command reports on the status of fans installed in position
11.3 Output Voltage Related Commands
11.3.1 FRU Data Format
The information to be contained in the FRU device is shown in the
following table.
Bits Meaning
7 Invalid Or Unsupported Command Received
6 Invalid Or Unsupported Data Received
5 Packet Error Check Failed
4-3 Not support, set to 0
2 Reserved, read 0
1-0 Not support, set to 0
Bits Meaning
7 Fan speed less than 800 rpm during over 10 seconds
If the fan control to stop condition will not set this bit
6 Not support, set to 0
5
Fan speed less than target 3800 rpm, during over 5 seconds
If the fan control target less than 4600 rpm, The warning and fault bit
may be together setting.
4-0 Not support, set to 0
Command Meaning Value
VOUT_MODE Linear data format, N = -9 17h
Address Value Description Remark
00H 01 Common header format version Common header
01H 00 Internal use area starting offset No used
02H 00 Chassis info area starting offset No used
03H 00 Board area starting offset No used
04H 01 Product info area starting offset
05H 0A Multi record area starting offset
06H 00 PAD
07H F4 Common Header Checksum

17
08H 01 Product area format version Product header
09H 09 Product area length
0AH 19 Language (English)
0BH C9 Manufacturer name / length
0CH 4C L
0DH 45 E
0EH 41
A
0FH 44 D
10H 20
11H 59 Y
12H 45 E
13H 41
A
14H 52 R
15H CC Model number / length
16H 54 T
17H 47 G
18H 31 1
19H 37 7
1AH 2D -
1BH 30 0
1CH 38 8
1DH 30 0
1EH 30 0
1FH 2D -
20H 30 0
21H 31 1
22H CF Customer information (max 15 bytes) Customer Name
23H 58
X：ASCII code
24H 58
X：ASCII code
25H 58
X：ASCII code
26H 58
X：ASCII code
27H 58
X：ASCII code
28H 58
X：ASCII code
29H 58
X：ASCII code
2AH 58
X：ASCII code
2BH 58
X：ASCII code
2CH 58
X：ASCII code
2DH 58
X：ASCII code
2EH 58
X：ASCII code
2FH 58
X：ASCII code

18
30H 58
X：ASCII code
31H 58
X：ASCII code
32H C3 Product version / length
33H 58
X：From A to Z To be updated
34H 58
X：From 0 to 9 To be updated
35H 58
X：Reserve To be updated
36H CF Product serial number / length
37H 58
X：T = LEAD YEAR, M = SMART, C = AMAX To be updated
38H 58
X：For LEAD YEAR model code (2 bytes)
39H 58 X
3AH 58
X：Year (00~99) date code To be updated
3BH 58 X To be updated
3CH 58
X：Week (01~52) To be updated
3DH 58 X To be updated
3EH 58
X：Product version (2 bytes) To be updated
3FH 58 X To be updated
40H 58
X：Serial number (000001~999999) To be updated
41H 58 X To be updated
42H 58 X To be updated
43H 58 X To be updated
44H 58 X To be updated
45H 58 X To be updated
46H C0
A
sset tag / length
47H C0 FRU File ID type/length byte
48H C1 No more info fields
49H 00 PAD (Always zero)
4AH 00 PAD (Always zero)
4BH 00 PAD (Always zero)
4CH 00 PAD (Always zero)
4DH 00 PAD (Always zero)
4EH 00 PAD (Always zero)
4FH 61 Product area checksum
50H 00 Power supply information Multirecord
51H 02 Record format version Header
52H 18 Record length
53H 96 Record checksum To be updated
54H 50 Header checksum To be updated
55H 0C Output power (2 bytes) 780W

19
56H 03
57H 28 Peak VA (2 bytes) 1320W
58H 05
59H 23 Inrush current 35A
5AH 0A Inrush interval in ms 10ms
5BH 10 Low end Input voltage range 1 100V
5CH 27
5DH C0 High end Input voltage range 1 240V
5EH 5D
5FH 28 Low end Input voltage range 2 90V
60H 23
61H 20 High end Input voltage range 2 264V
62H 67
63H 2F Low end Input frequency range 47Hz
64H 3F High end Input frequency range 63Hz
65H 0C Input dropout tolerance in ms 12ms
66H 1A Hot swap, Power factor correction support
67H
54
Peak wattages
852W
68H F3 15S
69H 00 Combined Wattage (3 bytes) No used
6AH 00 No used
6BH 00 No used
6CH 00 Predictive fail tachometer lower threshold (RPS)
6DH 01 DC output Multirecord
6EH 02 Record format version Header
6FH 0D Record length
70H 86 Record checksum
71H 6A Header checksum
72H 01 Output number 1 +12V
73H B0 Nominal voltage 12V
74H 04
75H 74 Maximum negative voltage 11.4V
76H 04
77H EC Maximum positive voltage 12.6V
78H 04
79H 78 Ripple and noise pk-pk 10Hz to 20MHz 120mV
7AH 00
7BH 00 Minimum output current 0A