SilverStone ST50NF User manual

April, 2011
ST50NF
NIGHTJAR SERIES
Industrial-class fanless power supply
Fan-less thermal solution, 0 dBA acoustics
Efficiency 82%~85% at 20%~100% loading
500W continuous power output
Strict ±3% voltage regulation
PCI-E 8pin and PCI-E 6pin connector support
Powerful class-leading single +12V rail
Aluminum construction
Server-level components
Support ATX 12V 2.3 & EPS 12V
Active PFC
NO:G11214010

ST50NF
Silverstone Nightjar
ST50NF
ATX12V / EPS 12V Switching Power Supply
With Active PFC
Fan-less Thermal Solution
80Plus Bronze
PS/2
The power supply shall be operated at universal input voltage defined in the following table.
Lnput Voltage
Voltage
MIN
99
NOM
110-240
MAX
264
1. Input Requirements
1-1. Input Voltage
The input frequency range is from 47Hz to 63Hz.
1-2. Frequency
The max inrush current is 100A for 115/230VAC.
1-3. Inrush Current
1-3-1. Cold Start
01
Conditions
o
Limits
115/230VAC, full load.
25 C ambient. No component over stress or damage should occur to
the power supply.Input fuse
shall ot blow.
02
1-3-2. Warm Start
Conditions
o
Limits
Turn off at 132/264VAC full
load for 1 sec then turn on
at the peak of the input
voltage cycle at 25 C ambient.
No component over stress
or damage should occur to
the power supply.
Input fuse shall not blow.
1-4. AC Input Current
AC Input
115V
230V
Units
AMPS
AMPS
MAX
6.5
4
Output Voltage
+5V
+12V
-12V
+3.3V
+5Vsb
MIN
+4.75
+11.40
-10.80
+3.135
+4.75
Nominal
+5.00
+12.00
-12.00
+3.30
+5.00
MAX
+5.25
+12.60
-13.20
+3.465
+5.25
Units
Volts
Volts
Volts
Volts
Volts
Range
± 5%
± 5%
± 10%
± 5%
± 5%
The minimum power supply system efficiency shall be >82%, measured at nominal
input voltage 115V or 230V and full loading.
1-5. Efficiency
3.5ma max, At 240Vac/60Hz
Note:
1. The above voltage range should also include ripple and noise.
2. The output voltage should be measured at the terminals of output connector.
1-6.Leakage current
2-1. Output Regulations
2. Output Requirements

ST50NF
The DC loads shall remain within the ranges specified in 2-2 DC Load Requirements and the DC
output voltages also shall remain within the regulation ranges specified in 2-1 Output Regulation
when measured at the load end of the output connectors.
1
2
3
+5V
0.5
18
1
+3.3V
18
0.5
1
+12V
0.5
10
38
-12V
0.5
0.5
0.5
+5VSB
0.1
0.1
0.1
2-2-1. Cross Regulation
The +5Vsb is on whenever the AC power is present.
Note: The measurements should be made by crossing a 47uf/ electrolytic and a 0.1uf ceramic disk
capacitors at each output with measuring bandwidth from DC to 20 mhz. If ambient temperature is
under 20 C or over 30 C, the AC input should be nominal input.
Figure 1. Differential Noise Test Setup
2-3. +5V standby voltage
03
Output Voltage
+5V
+12V
-12V
+3.3V
+5Vsb
Ripple & Noise Max
50
120
120
50
50
Units
Mv
Mv
Mv
Mv
Mv
2-2-1. Cross Regulation
oo
04
2-5. Total Output Power
Ac Input Voltage
99V~264Vac
MAX
500
Units
Watts
MAX
500
Units
Ms
The power supply outputs shall be enabled with an active-low TTL signal.
When TTL signal is low, the DC outputs are to be enabled.
When TTL signal is high or open circuited, the DC outputs are to be disabled.
Electronic means or a mechanical switch may activate the TTL signal.
After the TTL signal is active high, must wait for 3 seconds before active low again.
2-6. Remote ON/OFF Control
FIGURE 2. Power Sequence
The test environment is 25 C condition
@ nominal input. See1-1
2-8. Power On Time (T1)
MAX.
70
Units
Ms
2-9. Rise Time (T2)
MIN.
100
MAX.
500
Units
Ms
2-10. Power Good Delay Time (T3)
MAX
10
Units
Ms
2-11. Power Good Rise Time (T4)
2-7. Power Sequence
o

ST50NF
Power good signal shall go to a down level 1ms before +5V output
voltage falls below the regulation limits during PS-ON signal pull high.
2-13. Power Fail Signal (T6)
When the DC outputs (+5V, +12V, +3.3V) have over voltage condition,
the power supply shall provide latch mode over voltage protection.
3-1. Over Voltage Protection
A short circuit placed to ground shall cause no damage or power supply shall be shutdown.
(The contact resistance is 0.05 ohm when the outputs short circuit.)
3-2. Short Circuit Protection
When the power supply latches into shutdown condition due to a fault on an+5V,+3.3V,+12V,
output (OVP, UVP,OCP)and OTP, the protection shall reset after the fault has been removed,
use remote on/off control or recycle the AC power again for a typical of 5 seconds.
3-3. Protection Reset
Any output overshoot at turn on shall be less than 15% of the nominal output value
(with resistive load) as described in sec. 2.1.
3-4. Over Shoot
3. Protections
05
DC output
+12V
+5V
+3.3V
Max
16.0
7.0
4.5
Unit
V
V
V
MIN.
16
Units
Ms
MIN.
1
Units
Ms
2-12. Hold Up Time (T5)
The test environment is 25 C & full
load condition @ nominal input.
o
06
At 115/230Vac input the power supply will shut down all DC output within max. 150% of full load.
3-5. Over Power Protection
Max.160% for +5V,+12V,+3.3V dc output rail.
3-6. Over Current Protection
When power supply temperature over 90 C (typ.)The power supply will be shutdown.
FIGURE 3. Operation/Storage Temperature Range
Caution: Fanless power supply recommends the systems require
additional external forced circulation cooling fan to extend product life.
3-7. Over Temperature Protection( Optional )
Operation: 20% to 90% RH(nominal input)
Storage: 5% to 95% RH
4-2. Humidity (none condensing)
Operation:
115V: 0 C to 35 C (Need to increase external forced air cooling) -P1(Note.)
230V: 0 C to 45 C (Need to increase external forced air cooling) -P2(Note.)
4-1. Operation/Storage Temperature Range
4. Environment
o
oo
oo

ST50NF
5-1. UL 60950-1, 2005 (2nd Edition.)
5-2. BSMI (CNS14336: 94)
5-3. TUV EN 60950-1: 2006+A11
5-4. CB
5. Safety
6-1. CE
6-2. BSMI (CNS13438: 95)
6-3. FCC Part 15 Subpart B, Class B at system load
6-4. CISPR 22 AS/NZS CISPR 22: 2006, CLASS B
6. EMI Requirements
The power supply shall withstand for 3 seconds without breakdown the application of an 1800Vac-supply
voltage applied between both input line and chassis (10ma AC Cutoff current). Isolating transformers shall
similarly withstand 4242Vdc applied between both primary and secondary windings for a minimum of one
minute.
7. Dielectric Voltage Withstand (HI-POT)
Active Power Factor Correction, complies with EN 61000-3-2: 1995 + A1 + A2: 1998, Class D.
8. PFC
Comply with IEC 61000-4-2.
9. Electrostatic Discharge (ESD)
Comply with IEC 61000-4-4.
10. EFT/ Burst
Comply with IEC 61000-4-5.
11. Surge
Applying 115 Vac ± 10 % or 230 Vac ± 10% input voltage and maximum load (60%)
for this product in 45
± 5 C chamber.
12. Burn-In
The power supply shall have a minimum mean time between failure greater than
80,000 hours Minimum (Without Cooling Fan) at continuous operation of 100%
load and an ambient temperature of 25 C.
13. M.T.B.F.
07
o
o
08
There are two leds for the monitoring the status of the power supply,which allows
users to perceiveA full awareness of the working condition of the power supply.
The temperature LED indicates surface temperature of the power supply’s housing cage.
14. LED Indicators
Dimension (W x H x D): 150mm (5.90”) x 86mm (3.38”) x 160mm (6.29”)
15.1. Physical Dimension
M/B 24PIN connector
15. MECHANICAL REQUIREMENTS
The Status-LED indicates power
supply’s working.
Caution: DO NOT TOUCH THE SURFACE OF POWER SUPPLY WHEN
THE TEMP-LED INDICATES RED, IT MIGHT BE DANGEROUS.
Temp. Status
High 55 C
Low 55 C
LED Color
Red
Green
o
o
>
=
>
Orange
Blue
Black
Green
Black
Black
Black
White
Red
Red
Red
Black
Signal
+3.3V
-12VDC
COM
PS-ON
COM
COM
COM
N/C
+5VDC
+5VDC
+5VDC
COM
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Signal
+3.3V
+3.3V
COM
+5VDC
COM
+5VDC
COM
PWRGOOD
+5Vsb
+12V
+12V
+3.3V
Orange
Orange
Black
Red
Black
Red
Black
Grey
Purple
Yellow
Yellow
Orange
Power Status
Standby
Power ON
Power Fault
LED Color
Amber
Green
Red

ST50NF
09
EPS 12V 8PIN connector
Yellow
Yellow
Yellow
Yellow
Signal
+12V
+12V
+12V
+12V
Pin
5
6
7
8
Pin
1
2
3
4
Signal
COM
COM
COM
COM
Black
Black
Black
Black
ATX 12V 4PIN (4+4PIN EPS 12V in split mode)
Black
Black
Signal
GND
GND
Pin
1
2
Pin
3
4
Signal
+12V
+12V
Yellow
Yellow
SATA connector
Orange
Black
Red
Black
Yellow
Signal
+3.3V
COM
+5V
COM
+12V
Pin
5
4
3
2
1
4PIN peripheral connector (HDD) 4PIN floppy connector (FDD)
Yellow
Black
Black
Red
Signal
+12V
COM
COM
+5VDC
Pin
1
2
3
4
Pin
1
2
3
4
Signal
+5VDC
COM
COM
+12V
Red
Black
Black
Yellow
10
8PIN PCI Express connector
Yellow
Yellow
Yellow
Black sense1
Signal
+12V
+12V
+12V
COM
Pin
1
2
3
4
Pin
5
6
7
8
Signal
COM
COM
COM
COM
Black
Black
Black
Black
6PIN PCI Express connector
Yellow
Yellow
Yellow
Signal
+12V
+12V
+12V
Pin
1
2
3
Pin
4
5
6
Signal
COM
COM
COM
Black
Black
Black