SIM Roulette SR-Nano-500 User manual

User manual
SR-Nano-500 / SR-Nano-1000

EQUIPMENT
SIM aggregator
Disk container
Manual
SD card (depending on equipment)
1
1
1
1
GETTING STARTED WITH THE DEVICE
Disk container
Zero Row / Place A0
Track A
Track B
Track C
...
Retainer hole
disk-container
On the side:
Connector for external
devices
according to the RS-485
standard (not in all
configurations)
Attention! This connector
is not intended to
connect the device to the
Internet.
SD card slot (optional)
Power supply connector
12V/2A connector diameter 0.2 inch
Connector for connection
modem
Multifunctional
touch button
Screen or indicator
(depends on the
configuration)

INSTALLING THE DISC CONTAINER
1. Pull the disc carrier retainer out of the hole.
2. Slightly spreading the upper and lower support panels of the device to the
sides, slide the container disk into the SIM aggregator so that the central hole of
the container disk is coaxial with the lock hole.
3. Replace the retainer.
CONNECTING TO A LOCAL NETWORK
The SIM aggregator connects to the local network and to the Internet only
via WiFi.
By default, the device is configured to connect to a network with the name (SSID):
SIM and password: roulette
To change the connection parameters, you can use the following advice:
1. Set up a SIM hotspot with the password roulette on your mobile phone.
2. Turn on the SIM aggregator and make sure that it connects to the created WiFi
network.
3. In the mobile phone browser, go to the address http://sim-roulette.local or
http:// IP_address_your_SIM_roulette (the IP address is displayed in the top line
of the device display when connected to the network).
4. Log in. By default, login: admin, password: admin.
5. Go to the Settings/Network section, select your work network and enter the
password.
6. Save settings. After restarting, the SIM aggregator will connect to the selected
network.

BEGINNING OF WORK
1. Connect the GSM modem to the connector (shown in the figure).
2. Place the Nano SIM card in slot A0 (shown in the figure).
3. Go to the WEB-interface Terminal section.
4. If there is a stable connection with the device, the upper signal line should be
green, if there is no connection — gray.
5. Enter the command card:A0. The command will position the carriage contacts
over the SIM card in cell A0.
6. Enter the command modem>connect. The command will connect the GSM
modem to the SIM card.
7. Enter the command modem>on. The command will turn on the GSM modem.
8. To check the connection of the SIM card to the cellular network, use
command modem>send:AT+CREG? (with an interval of 2-3 seconds).
While the connection is in progress, the modem returns a code of 0.2; successful
codes connections 0.1 and 0.5; error codes 0.0 and 0.4; code 0.3 usually means
that the SIM card is blocked.
9. As a check, make an outgoing call with the
modem>send command:ATD+79001234567;
Complete list of AT commands: sim-roulette.com/en/doc/at
API SR-Nano: sim-roulette.com/en/doc/sr-nano
Calibrating SR-Nano: sim-roulette.com/en/doc/sr-nano-mekhanika
Applications for SIM Roulette: sim-roulette.com/apps
If you plan to work with the aggregator using the WEB-panel
SR-Navigator, we recommend registering at sim-roulette.com and
familiarizing yourself with the capabilities of this software.

HELP AND SUPPORT
WEB-site: sim-roulette.com
Technical documentation: sim-roulette.com/en/doc
Форум: sim-roulette.com/forum
Forum: [email protected]
We recommend registering on the website sim-roulette.com
and link the aggregator to your account.
Thank you for purchasing the SR-Nano and wish you fruitful work!