SIMPA UZW11RM User manual

即熱式氣體熱水爐
Instantaneous Gas Water Heater
型號 Model : UZW11RM / UZW11TM
使用說明書
User Manual
香港煤氣適用
For Hong Kong Town Gas
UZW11RM UZW11TM

目錄
重要安全指示 …………………………………………………………… 1第頁
產品介紹 ………………………………………………………………….. 4第頁
操作指示 ………………………………………………………………….. 5第頁
保養 …………………………………………………………………………. 7第頁
故障處理 ……………………………………………………………………. 7第頁
規格 ……………………………………………………………………….... 8第頁
注意!
根據香港氣體安全條例，任何氣體裝置工程，包括爐具和接駁喉管的安裝，
必須由註冊氣體裝置技工執行，而該技工已於相關的氣體工程類別註冊及受
聘於註冊氣體工程承辦商。

1
重要安全指示
為安全使用本熱水爐，請遵照下列各項指示。有關符號的意思如下：
上述描述所導致的受傷及財物損毀情況，請參考下列詳細描述。
 受傷：出現受傷，燙傷和觸電危險時，須要送院治理或長期留院治療。
 財物損毀：對房屋及傢俱等物件造成廣泛損毀。
危險 若忽視此符號，並錯誤使用熱水爐，可能引致死亡或嚴重受傷和發生火警的危險。
警告 若忽視此符號，並錯誤使用熱水爐，可能引致死亡或嚴重受傷，亦可導致火警發生。
注意 若忽視此符號，並錯誤使用熱水爐，可能會引致受傷和財物損毀。
危險、警告、注意 禁止 切勿觸摸 必須執行 切勿拆開 必須接到地線
危險
若果發現爐具出現問題
 當使用熱水爐時，若發現異常的火焰、氣味或特別的聲音，請
立即關閉熱水龍頭及煤氣錶掣，並通知煤氣公司安排檢修。
 在發生地震或火災時，請立即停止操作熱水爐。
1. 關閉水龍頭
請勿將排氣管的出口置於室內
 排氣管的出口必須面向室外地方。
若你發覺有煤氣洩漏
1. 請停止使用本熱水
爐，並關閉煤氣錶掣。
2. 開啟窗戶讓煤氣排
出屋外。
3. 使用室外電話與煤
氣公司緊急事故熱線
2880 6999聯絡。
若發生燃氣洩漏
 切勿點燃明火、插拔電源插頭。
 禁止開、關電器產品。
 切勿在附近使用電話、手機。
當發覺有燃氣洩漏，切勿進行所述事項，直至維修工作完成為止。
切勿在漏氣處理完畢前再次打開煤氣掣。
關閉
關
開
2. 關閉煤氣錶掣
關閉
煤氣錶掣
關閉
水龍頭

2
警告
請小心看管兒童
 流放熱水到浴缸時，切勿讓兒童在浴室玩耍，以免兒童不小心掉進浴缸，引致危險。
 切勿讓兒童單獨洗澡。
切勿自行拆卸、維修或改裝爐具
 熱水爐的安裝、維修及其他附帶工程，必須由受僱於註冊氣體工程承辦商及領有適當級別的註冊氣體
裝置技工進行，以免造成危險或損毀爐具。
切勿遮蓋排氣管的出口
 切勿因建築更改引至排氣口位於室內，以避免引致一氧化炭中毒或火警危險。
注意
重要安全指示
請依照下列指示以防燙傷
 當使用熱水後，立即開啟熱水龍頭或迅速減慢熱水流出時，
熱水可能會突然噴出。為避免燙傷危險，切勿將熱水直接噴
灑在頭和身體上。
 當使用花灑時，請先用手確認水溫。切勿直接將熱水噴灑在
頭或身體上。
 切勿觸摸煙囪或排氣管，避免燙傷。
遵照下列的指示，避免火警發生
 如圖所示，請將物件與爐具保持適當距離。
 切勿於熱水爐或煙囪周圍擺放或使用易燃物品、揮發
性物質或噴霧器。
有關用途
 熱水爐供應熱水給浴室或廚房使用，切勿用作其他用途，以免發生意外或損壞爐具。
 請勿將長期儲存於熱水爐內的水，用作飲用或煮食用途。
 為免縮短熱水爐的壽命，請勿用於商業用途。
先用手確認水溫 切勿觸摸煙囪
10 厘米
10 厘米 60 厘米

3
注意
重要安全指示
有關安裝
 嚴禁安裝於室外地方。
 請盡量縮短熱水喉管的長度，以及避免水管有可能導致閉塞及滯水的地方。
 盡量縮短熱水出口與水龍頭的距離。
 安裝排氣管時，請確保排出的煙氣不會直接排向外牆、窗戶、玻璃、鋼門或鋁窗框等物件，
這或會引致這些物件出現變形及變色。
有關熱水爐控制器
 請勿讓小孩隨意按動熱水爐的控制器。避免造成意外或損毀爐具。
預防病菌滋生(例如：退伍軍人病菌)
 若熱水爐已停用超過一星期，於使用前，應將滯留於水管內的水先排走。
 進行排水時，請盡量避免產生水霧，應使用延伸水管連接出水口及排水位。
 排水方法 :
- 關閉熱水爐，將距離熱水爐最遠的熱水水龍頭完全開啟 1 分鐘
有關清潔及保養
 若熱水爐或喉管接觸到含氯除菌劑、酸性浴室清潔劑、除臭劑或食鹽，請用大量的清水把它們
沖掉，避免造成意外或損毀爐具。
 切勿使用溶劑或油性清潔劑清潔爐具，這會引致變色或變形。

4
產品介紹
UZW11RM / UZW11TM
面板控制器
面板控制器
冷水接口 熱水接口 冷水接口
煤氣接口
熱水接口
開/關按鈕
 用於開啟或關閉熱水爐。
 按下按鈕開啟熱水爐，溫
度顯示屏會亮起。
溫度顯示
 顯示熱水溫度設定。
 若熱水爐出現異常時，
故障信號會閃爍顯示。
高溫指示燈
 當熱水溫度設定達50oC
以上，指示燈便會亮起。
使用中指示燈
 當熱水爐運作時，指示
燈便會亮起。
水溫調較按鈕
 用作設定熱水溫度。

5
1）開啟熱水爐
 開啟熱水爐的電源後，按面板控制器上的開/關按鈕。
 溫度顯示屏亮起，此時熱水爐處於備用狀態。
 安裝後首次使用時，預設溫度 42℃ 顯示於顯示屏上。
2）設定熱水水溫
 按「 」按鈕調高水溫，或按「 」按鈕調低水溫。
 設定溫度可由 35℃ 調較至 60℃，溫度設定會顯示於溫度顯示屏。
3）使用熱水
 當開啟熱水水龍頭時，熱水爐立即運作，使用中指示燈會亮起。
 熱水流量少於每分鐘 2.5 公升，燃燒器便會關閉。
 熱水爐運作時，熱水溫度設定不可高於 48℃。
 熱水爐運作時，如溫度設定在50℃或以上。高溫指示燈會亮起，
溫度只可下調。
4）停止操作
 關閉熱水龍頭，熱水爐停止運作，使用中指示燈熄滅。
 按下開/關按鈕關閉熱水爐，溫度顯示屏及所有顯示燈會關掉。
注意
 為避免燙傷，淋浴時請先用手確認水溫，切勿將熱水正接噴灑往頭部和身上。
 為避免燙傷，使用高溫的熱水後，水管中仍存有高溫熱水，再次使用熱水時，請務必先用手確認
熱水的溫度後才使用。
 長時間不使用熱水爐時，請關閉電源、進水閥、供氣閥。
熱水水溫設定
操作指示
關閉熱水龍頭
調高水溫
調低水溫
開/關按鈕 溫度顯示屏
使用中指示燈
高温指示燈
清洗碗碟溫度 沐浴溫度 高溫

6
操作指示
 火焰失效：當沒有火焰時，感應棒會停止傳送火焰信號到主控器，以停止供氣到燃燒器。
 殘火安全裝置：當水龍頭已經關閉而火焰仍然存在，而在熱交換器內的水溫高達 105℃時，雙金屬安
全裝置會關閉電磁閥停止供氣。
 過度沸騰：當熱水溫度高於 90℃，熱水熱敏電阻信號將傳送到主控器停止供氣。
 水流量感應裝置：若進入的水流受到阻隔或被中止。水流量感應器會停止傳送磁脈衝信號到主控器, 並
停止供氣。
 過熱保護：若熱交換器燒毀或溫度高達 139℃時，過熱保護裝置會啟動，停止熱水爐運作。
 防止過高水壓裝置：若熱水爐內的水壓高於 2100kPa，置於熱水出口的洩壓閥會打開，釋放已累積的
壓力，待水壓降回 1500kPa 的水平才會關閉。
 助燃風扇轉速檢查：風扇的轉速由轉速感應器所監測；若風扇轉速與要求速度有所偏差，訊號將會傳
送到主控器，而轉速亦會作出相應的調整。
 UZW11RM / UZW11TM 熱水爐可以提供每分鐘 11 公升流量，升溫 25℃ 的熱水，適合在不同季節
的一般沐浴使用。您可以在控制面板設定所需的熱水溫度，熱水爐將會自動調控出水溫度。但是在一
些特殊情況下，除通過控制面板設定熱水溫度外，可同時調節熱水流量，以便達到所需溫度。
 在冬季偶有極寒冷的天氣，自來水的溫度可能過低或熱水流量過大，熱水爐的出水溫度可能低於設定
的溫度，您可以調節水龍頭或花灑掣來減少熱水流量，以便獲得適合的水溫。
 在夏季偶有極炎熱的天氣，自來水的溫度可能過高或熱水流量過小，熱水爐的出水溫度可能高於設定
的溫度，您可以調節水龍頭或花灑掣來增加熱水流量，或輔以混合冷水，以便獲得適合的水溫。
安全設施
恆溫熱水爐調控熱水溫度提示

7
保養
1) 機身不可用溶劑清潔，應使用濕軟布揩抹，再用乾軟布揩乾。
2) 如花灑出水變慢，花灑水孔可能堵塞，應加以清理。
3) 應定期檢查及保養熱水爐，可保安全及高效率使用。
故障處理
安全裝置會持續監察熱水爐運作。當故障發生時，故障信號會在溫度顯示器上閃動，方便處理有關問題 。
當詢問維修服務時，請說出有關故障信號。
在一般情況下，打開然後關閉熱水龍頭，故障信號便會被清除。如故障信號仍然存在，可嘗試關上電
源，等待 10 秒後重啟熱水爐。若故障顯示仍然存在，請致電煤氣公司客戶服務熱線 2880 6988。
在寒冷及潮濕天氣，排煙管出口偶會冒出煙霧，這是煙氣中的水氣遇冷轉為白色煙霧所致，這是正常現象。
故障信號 故障內容 處理方法
11 點火失誤
關掉面板控制器，然後檢查煤氣閥是否開啟，煤氣供
應是否中斷。若煤氣供應正常，重新開啟電源，當開
和關熱水龍頭數次後(每次開關相隔約10秒)，沒有出
現故障顯示，說明熱水爐可以正常使用。如故障信號
仍然存在，請致電煤氣公司客戶服務熱線。
12 熄火安全裝置啟動 請致電煤氣公司客戶服務熱線
14 過熱保護裝置啟動 請致電煤氣公司客戶服務熱線
15 殘火安全裝置啟動 請致電煤氣公司客戶服務熱線
32 入水温度感應器故障 請致電煤氣公司客戶服務熱線
35 出水温度感應器故障 請致電煤氣公司客戶服務熱線
61 助燃風扇故障 請致電煤氣公司客戶服務熱線

8
規格
本產品符合香港《電氣產品（安全）規例》。
型號 UZW11RM UZW11TM
基本規格
熱水爐類別 機動排煙密封式
排氣方式 背排 頂排
機身尺寸（毫米） 370 （闊）x 675 （高）x 135 （深）
重量（千克） 15
燃氣種類 香港煤氣
供氣壓力（千帕） １.５
接駁
煤氣 3/4 ＂BSP
冷水 G1/2
熱水 G1/2
電源供應 220 伏特 / 50 赫 交流電
排煙管道 Ø110 x Ø75 Ø100 x Ø60
最長管道 不適用 5米3 彎
（一彎位約等於 2 米）
運作系統
點火 自動電子點火
供水能力［T=25℃］， （公升/分鐘） 2.5 至11.0
最少熱水流量（公升/分鐘） 2.5
最少運作水壓（千帕） 10
建議供水壓（千帕） 100 至 700
溫度選擇 35℃ - 48℃, 50℃, 55℃, 60℃
安全裝置
熄火安全裝置 火焰感應棒
水流量檢測裝置 水流感應器
殘火安全裝置 雙金屬開關（105℃）
過大電流保護裝置 保險絲（2A）
防止過高水壓保護裝置 水洩壓閥 （啟動：2.1 兆帕 ）
助燃風扇檢測裝置 轉速感應器
防止過熱保護裝置 熱斷流器（139℃）
防止沸騰裝置 熱敏電阻（90℃）
漏電保護裝置 漏電斷路器
額定熱負荷
最高 (千瓦) 27.0
最低 (千瓦) 6.5
耗電量 (瓦) 47

Contents
Important Safety Instructions ………………………………….. P. 10
Product Description ………………………………………………... P. 13
Operating Instructions ……………………………………………. P. 14
Maintenance …………………………………………….................... P. 16
Trouble Shooting ……………………………………………………. P. 16
Specifications ……………………………………………................... P. 17
Attention!
According to the Gas Safety Ordinance of Hong Kong, any gas
installation works including the installation of appliances and
connection tubing, must be undertaken by registered gas
installers who are registered for that appropriate classes and be
employed by registered gas contractors.

10
Important Safety Instructions
In order to use this appliance safely, please follow the following instructions . Meanings of the symbols are as follows.
The above injuries and material damage refer specifically to the followings.
 Injury: injuries, burns and electric shocks etc. that require treatment in hospital or long-term
hospitalization.
 Material Damage: widespread damage to house and furnishings.
Danger
If you ignore this warning sign and act mistakenly , it may incur death, serious injury and
explosion risk.
Warning
If you ignore this warning sign and mistakenly handle the appliance, it may incur death, serious
injury and fire incident.
Caution
If you ignore this warning sign and mistakenly handle the appliance, it may incur injury or
material damage.
General danger,
warning or caution Forbidden Do not touch Be sure to do Disassembly is forbidden Must be earthed
Danger
If you notice something wrong with the appliance
 If you notice abnormal flames, gas smell or strange sounds, please
turn off the water tap and gas meter valve immediately and contact
the Towngas company.
1. Turn off the water
tap
Do not place the outlet of flue terminal indoor
 The outlet of flue terminal should be faced outdoor.
If you notice a gas leak
2. Open all windows
to disperse the gas.
3. Call Towngas
Emergency Hotline
on 2880 6999 with a
phone outside the
premises.
If there is a gas leak
 Do not ignite a fire, insert or remove power plug.
 Turn on or off any electrical appliance is forbidden.
 Do not use nearby telephone or mobile phone.
When there is a gas leak, do not do any of the above actions until repair work has been completed .
Do not re-open the gas valve until the gas is no longer leaking .
Turn off
OFF
On
2. Turn off gas meter
valve.
Turn off
water tap
Turn off gas
meter valve
1. Cease use and
close the gas meter
valve

11
Important Safety Instructions
Warning
Care to be taken with children
 Do not allow children to bath alone.
Self disassembling, repairing and modification of appliance are strictly forbidden

who are registered for that appropriate classes and be employed by registered gas contractors in
order to avoid danger and appliance damages.
Do not cover the outlet of the flue terminal
 Do not place the flue terminal indoor due to building modification in order to avoid the occurrence of
carbon monoxide poisoning or fire.
Caution
Observe the following instructions to prevent scalding
 When you open the tap again after using hot water or quickly
reduce the hot water flow, hot water may suddenly come out. As
there is a risk of being scalded, do not direct the water onto your
head or body.
 When shower, taking check water temperature with hand first. Do
not direct the water onto your head or body.
Always check the
water temperature
with your hand first
Never place your
hand on or touch the
flue terminal
 Do not touch flue terminal or flue duct to prevent from scalding.
Observe the following instructions to prevent fire
 Keep thing away from the appliance to the distance as shown in the
figure.
 Do not place or use flammable materials, volatile substance or
aerosol around the water heater or flue terminal.
Regarding use
 Do not use the water heater for purpose other than hot water supply in bathroom or kitchen. This is
intended to prevent accidents or damage.
 Do not drink or use for cooking with water stored in the unit for a long time.
 Do not use it for commercial application lest its service life is reduced.
10 cm
10 cm 60 cm
Flue terminal

12
Important Safety Instructions
Caution
Regarding installation
 Do not place or install it at outdoor.
 Minimize pipe length and avoid dead legs and stagnant corners in hot water pipework.
 Minimize the distance between hot water outlet and water tap.
 When installing the flue terminal, make sure that the flue gas does not discharge directly to outside
walls, windows, glass, mesh doors or aluminum sashes etc. This will cause material disfiguration or
discolouration.
Regarding use of control
 Keep the control unit out of reach of children. In order to prevent accidents
or appliance damage.
Prevention of Bacteria Cultivation (e.g. Legionella)
 If water heater is not used for more than one week, drain away stagnant water of pipework before use.
 During water purging, avoid generation of water mist. Use extension pipe to connect water outlet and
drain point.
 Method of water purging :
- Turn off water heater and fully open the hot water tap of most far away from water heater for 1
minute.
Regarding cleaning and maintenance
 If chlorine-based fungicides, acidic bathroom cleaners, deodorants or salt touch the appliance or gas
pipe etc, wash them off with ample water straight away. They will cause unforeseen accidents or
appliance damage.
 Do not use solvent or oil-based cleaners to clean the appliance. This could cause discolouration or
disfiguration.

13
Product Description
UZW11RM / UZW11TM
Front Panel Control
Front Panel Control
Cold Water Connection
Gas Connection
Hot Water Connection
Cold Water Connection
Hot Water
Connection
Temperature Display
 Show hot water temperature
setting
 Display error message and
blink when malfunction occurs
ON/OFF Button
 Use to switch on or off water
heater
 Press the button to switch on
water heater. The temperature
display lights up.
In Use Indicator
 Indicator lights up when
water heater is in use
Temperature Control Button
 For setting
water temperature
High Temperature Indicator
 Indicator lights up when
temperature setting is 50oC
or above

14
Operating Instructions
1) Switch on water heater
 Switch on power supply of water heater and press ON/OFF button on
front panel control .
 Temperature display lights up and the water heater is ready for use.
 After new installation, default temperature of 42℃ will be displayed for
the first time usage.
2) Select hot water temperature
 Press “ ”button for a higher temperature or press “ ”
button for a lower temperature.
 Water temperature can be adjusted from 35℃ to 60℃ and shown on
the temperature display.
3) Use of hot water
 When turn on hot water tap, water heater operates automatically, in use
indicator lights up.
 When hot water flow is less than 2.5 L/min, the burner will be shut down.
 When water heater is operating, hot water temperature cannot be set
above 48℃.
 When water heater is operating and temperature setting is 50℃ or
above . High temperature indicator lights up and temperature setting
can only be decreased .
4) Stop operation
 Turn off hot water tap, water heater stops operating and in use indicator is off.
 Press the button to switch off the water heater. The temperature display and all
indicator lights will be off.
Caution
 To prevent scalding, check water temperature with your hand before use. Do not direct water onto the
head or body.
 When you turn on the tap again after using high temperature hot water, there is a risk of being scalded
as high temperature water may in the water pipe. Check water temperature with your hand before use.
 Turn off the power supply, the water inlet valve and the gas valve when the heater is not to be used for
a long period of time.
Control of Hot Water Temperature
Turn off hot
water tap
Temperature
display
ON/OFF button
In Use indicator
High temperature
indicator
Increase water temperature
Decrease water temperature
Dishwashing
temperature
Shower
temperature High
temperature

15
O p e r a t i n g I n s t r u c t i o n s
 Flame failure : When there is no flame. Flame rod stops sending flame signal to the main controller for
stopping gas supply to burner.
 Remaining flame safety device: If the flame remains on the burner after the water tap has been turned off
and the water temperature inside heat exchanger reaches 105℃ , bi-metal safety device shuts off the
solenoids and stops gas supply.
 Over boiling: If the hot water temperature reaches 90℃ , hot water thermistor sends signal to the main
controller to stop gas supply.
 Water flow sensing device : If water flow is restricted or stopped, the water flow sensor stops sending
magnetic pulse signal to the main controller for stopping gas supply.
 Over heat protection: If the heat exchanger burns out or the temperature reaches 139℃ overheat
protection device is activated to shut down water heater.
 Over pressure protection device: If the water pressure inside the water heater is over 2100kPa, the
pressure relief valve located near hot water outlet will open to release the built up pressure until it
reduces to 1500kPa and it will then be closed.
 Combustion fan revolution check: The fan revolution speed is continually monitored by a speed
detection sensor. If the fan speed deviates from the required speed, a signal is sent to the main controller
and the speed is adjusted accordingly.
 UZW11RM / UZW11TM water heater is capable to deliver 11L/min hot water at 25℃ temperature rise,
which is suitable for usual bathing purpose for all seasons. You can select the desired temperature by
setting temperature on control panel and the water heater will automatically provide hot water at that
temperature. However, under some exceptional situation, in addition to setting temperature on control
panel, you may require to adjust the water flow to attain the desired temperature.
 In winter, there may be occasional extremely cold weather where supply water temperature is exceptionally
low or required water flow is too high, the temperature of hot water may be less than the selected
temperature. You may appropriately reduce the hot water flow by adjusting water faucet or shower tap to
attain the suitable hot water temperature.
 In summer, there may be occasional extremely hot weather where supply water temperature is
exceptionally high or required water flow is too low, the temperature of hot water may be higher than the
selected temperature. You may appropriately increase the hot water flow or mixing with cold water by
adjusting water faucet or shower tap to attain the suitable hot water temperature.
Safety Device
Temperature Modulation Water Heater Temperature Setting Reminder

16
Maintenance
1) Never use solvents to clean the body of water heater. Please wipe the surface with a soft, damp cloth, then
dry with a soft cloth.
2) If the water flow at the shower is reduced, the shower head may be blocked. Check and clean if necessary.
3) It is necessary for the appliance to be inspected and maintained regularly so that it can be used safely and
efficiently.
Trouble Shooting
The safety devices check operation of the water heater continuously. If a fault occurs, a fault code flashes on the
temperature display . This assists to handle the problem. Please quote the code displayed when enquiring about service.
In general, fault code is cancelled when closing and re-opening hot water tap. If the fault code persists, turn off power
supply and wait for 10 seconds. Then, turn on the water heater again. If the fault code still persists, please contact
Towngas Customer Service Hotline on 2880 6988.
In cold and humid weather, cloudy mist may be occasionally vented from the flue terminal. The white
smoke is the condensate of water vapour in flue gases. It is a normal phenomenon.
Fault Code Details of Failure Remedy
11 Ignition failure
Turn off front panel control unit, and then check
whether the gas valve is turned on and the gas
supply is not interrupted. If gas supply is normal,
press ON/OFF button to switch on water heater. If
there is no fault code when the hot water tap is
turned on and turn off several times (wait for 10
seconds for each trial), the water heater is operating
normally. If the fault code still persists, contact
Towngas Customer Service Hotline.
12 Flame failure device activate Contact Towngas Customer Service Hotline
14 Overheating protection device activate Contact Towngas Customer Service Hotline
15 Remaining flame safety device activate Contact Towngas Customer Service Hotline
32 Incoming water temperature sensor faulty Contact Towngas Customer Service Hotline
35 Outgoing water temperature sensor faulty Contact Towngas Customer Service Hotline
61 Trouble with combustion fan Contact Towngas Customer Service Hotline

17
Specifications
This appliance complies with the Electrical Products (Safety) Regulation in Hong Kong.
Model UZW11RM UZW11TM
Basic
Specification
Water Heater Type Fan Draught Room-sealed
Flue Type Back Flued Top Flued
Dimensions（mm）370(W) x 675(H) x 135(D)
Weight（kg）15
Gas Type Hong Kong Town Gas
Gas Supply Pressure（Kpa）１.５
Connection
Gas 3/4 ＂BSP
Cold Water G1/2
Hot Water G1/2
Power Supply AC 220 V / 50 Hz
Flue Connection Ø110 X Ø75 Ø100 X Ø60
Max. Flue Length NA 5m 3bends (1 bend
equivalent to 2 meter)
Operation
System
Ignition Automatic spark ignition
Hot Water Capacity［Δ T=25℃］，（liter/
min）2.5 to 11.0
Min. Hot Water Volume（L/min）2.5
Min. Operating Water Pressure ( kPa ) 10
Recommended Water Supply Pressure
（kPa）100 to 700
Temperature Selection 35℃ - 48℃, 50℃, 55℃, 60℃
Safety
Device
Flame Failure Device Flame Rod
Water Flow Checking Device Water Flow Sensor
Remaining Flame Protection Device Bi-metal Switch（105℃）
Over Current Protection Device Fuse（2A）
Over Pressure Protection Device Pressure Relief Valve （ON：2.1 Mpa ）
Combustion Fan Checking Device Speed Detection Sensor
Overheat Protection Device Thermal Fuse（139℃）
Anti-boiling Protection Device Thermistor（90℃）
Earth Leakage Protection Device Earth Leakage Circuit Breaker
Rated Heat
Input
Maximum ( kW ) 27.0
Minimum ( kW ) 6.5
Electrical Consumption （W）47

201906