Simplicity 9518 Series User manual

OPERATOR’S
MANUAL
9518 SERIES
COMPACT DIESEL
TRACTOR
U|
FORM - 1671525
PRINTED IN U.S.A,
829

TO OUR DEALER
_ TO OUR DEALER _
_ DEALER’S PREDELIVERY SERVICE GUIDE FOR 15 PTO HP TRACTOR _
DETAILS OF ITEMS LISTED BELOW ARE COVERED IN THIS OPERATOR’S MANUAL OR IN THE
SERVICE MANUAL
SHIPPING DAMAGE
□ Tractor has been checked for shipping damage.
TRACTOR SET-UP
□ This tractor has been completely set-up in accord
with the Tractor Set-Up Instruction supplied with
the tractor.
PRE-OPERATIONAL CHECK, do before engine is started.
□ COOLANT LEVEL is between FULL & ADD MARK on
over flow bottle.
□ ENGINE OIL LEVEL is between “FULL” and “ADD”
marks on dipstick.
□ TRANSMISSION - HYDRAULIC System OIL LEVEL is
up to level mark.
□ AIR CLEANER ELEMENT is clean and properly
installed.
□ FWD axle oil level (if unit so equipped)
□ All air intake hoses and clamps are properly in¬
stalled and tightened.
□ A sufficient quantity of No. 2 diesel fuel for all
normal predelivery operation has been placed in the
fuel tank.
□ All Safety and Operational Decals & SMV Emblem
are properly installed and fully legible.
□ Check oil level in injector pump.
OPERATION AND ADJUSTMENT
□ Tire pressures are set within the pressures listed in the
Tires Pressure and Load Tables for the size tires on
this tractor.
□ Fan belt is properly tightened.
□ Battery electrolyte is at the indicator level and the
specific gravity is 1.240 or above in each cell.
□ Instruments and warning lights operate correctly.
□ Wheel guard lights are properly connected to the trac¬
tor wiring harness and all lights operate correctly in
the various light switch positions.
□ The safety start switches on clutch pedal & PTO shift
lever do not allow engine to start unless they are both
in disengaged position.
□ The brakes function properly and are adjusted
correctly.
□ The clutch functions properly and is adjusted correctly.
□ The engine Glow Plugs operate and the engine starts
correctly.
□ Throttle and fuel shutoff linkage operate correctly.
□ Engine low idle speed is 700 to 800 RPM, and high idle
speed is 2750 to 2850 RPM after engine is warmed up
to operating temperature.
□ Hydraulic relief pressure is approx. 1900 PSI (13100
kPa) at 2500 engine RPM.
□ All hydraulic functions operate correctly.
□ Transmission gear shift and range shift levers operate
smoothly in all gears.
□ Tractor operates properly in all gears.
□ After tractor has been operated and thoroughly warmed
up there are no leaks of:
□ a. engine oil.
□ b. power train and hydraulic oil.
□ c. radiator coolant.
□ Coolant anti-freeze tests to -20° F (-29° C) or lower.
□ All grease fittings on the tractor have been lubricated.
□ Overall appearance of tractor is clean and new.
□ Operator's manual is with the tractor

TO OUR DEALER
TO OUR DEALER
DEALER’S PREDELIVERY SERVICE GUIDE FOR 15 PTO HP TRACTOR
EXPLAIN TO YOUR CUSTOMER THE CARE, SAFE OPERATION AND ADJUSTMENT OF ITEMS LISTED BELOW:
LUBRICATION
BREAK-IN PERIOD
FRONT WHEEL BEARINGS
FWD OPERATION
ENGINE COOLANT TEMPERATURE
RADIATOR & ENGINE DRAIN PLUG
RADIATOR PRESSURE CAP
FAN BELT ADJUSTMENT
ENGINE OIL
PROPER FUEL
OIL FILTER
FUEL FILTER
OPERATOR’S CONTROLS & INSTRUMENT
PANEL
GEAR SHIFT
ENGINE CLUTCH
TOWING
SAFETY START SWITCHES
HYDRAULIC SYSTEM
DRAWBAR & 3-POINT HITCH
TRANSMISSION
BATTERY CARE
POWER TAKE-OFF
BRAKES
AIR CLEANER
LIGHTS
TIRE PRESSURE
WHEEL TREAD
STARTING & STOPPING (Tractor & Engine)
ACCESSORIES
STORING TRACTOR
USER'S RESPONSIBILITY & WARRANTY
OPERATOR’S MANUAL DELIVERED TO OWNER &
HE HAS BEEN INSTRUCTED AS TO
ITS CONTENTS
AGREE ON STARTING DATE IN FIELD &
100-HR. CHECK
OPERATOR’S SAFETY PRECAUTIONS, SHIELDS &
DECALS
TO OUR CUSTOMER
The following pages and illustrations are printed to help supply you with the knowledge
to better operate and service your new equipment.
We are proud to have you as a customer and feel you will be proud to be an owner of
this equipment.
Any piece of equipment needs, and must have a certain amount of service and mainte¬
nance to keep it in top running condition. We have attempted to cover all the adjustments
required to fit most conditions; however, there may be times when special care must be
taken to fit a condition.
Study this operator’s manual carefully and become acquainted with all the adjustments
and operating procedures before attempting to operate your new equipment. Remember,
it is a machine and has been designed and tested to do an efficient job in most operating
conditions and will perform in relation to the service it receives.
If special attention is required for some conditions, ask your authorized Dealer; his Parts
and Service Organization will be glad to help and answer any questions on operation and
service of your new machine.
A
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
A
This symbol is used to call your attention to safety precautions that should be followed
by the operator to avoid accidents. When you see this symbol - Heed Its Warning.

USER’S RESPONSIBILITY
USER’S RESPONSIBILITY
It is the responsibility of the user to read the Operator’s Manual and understand the safe and correct
operating procedures as pertains to the operation of the product, and to lubricate and maintain the pro¬
duct according to the maintenance schedule in the Operator’s Manual.
The user is responsible for inspecting his machine and for having parts repaired or replaced when contin¬
ued use of the product would cause damage or excessive wear to other parts. It is the user’s responsibili¬
ty to deliver his machine to an authorized dealer, for service or replacement of defective parts which are
covered by the standard warranty. When requesting warranty service, you must present your copy of deliv¬
ery record.
The user should notify his Selling Dealer in advance so arrangements can be made to have his 100-hour
or 30-day inspection performed. The user should not be charged for this inspection or adjustment, but is
expected to pay for oil, filters, or any parts and labor which are not covered by the standard warranty. The
user is responsible for bringing the product to the Selling Dealer's shop to have this inspection
performed.
If the Dealer is requested by the Customer to travel to another location, or haul the machine to his shop
for the purpose of performing a warranty obligation or free inspection, it would be for the Customer’s con¬
venience, and the cost for such trips is to be paid for by the Customer. Any arrangement whereby the
Dealer agrees to absorb all or a part of the cost of these trips is to be made between the Dealer and the
Customer and is to be considered a courtesy to the Customer.
The user will advise the dealer when unit will start in field so dealer representative carrbe on hand to
make necessary adjustments and help you get started properly.
We do notallow credit for the cost of travel time, mileage, or hauling as a warranty allowance.
WARRANTY .... Your warranty for new equipment will be received from your authorized dealer. You will
be required to pay any premium for overtime labor requested by you, any charge for making service calls
and for transporting the equipment to and from the place where warranty work is performed. Normal main¬
tenance service and repair work not covered by the warranty during the warranty period and all service
after the warranty period will be charged for at the dealer’s regular rates and prices. 7/79-6
THE NEW EQUIPMENT BATTERY SERVICE ADJUSTMENT POLICY
1. If within a period of 90 DAYS after day of sale to the original
user, the new equipment battery becomes unserviceable (not
merely discharged) in normal use, due to defective material or
workmanship, the company will replace it with an equivalent
new battery, without charge, to the original user.
2. If after the expiration of such 90 DAYS but before the expiration
of 24 months from date of sale to the original user (each such
month being designated herein as a unit of service) the new
equipment battery becomes unserviceable (not merely dis¬
charged) in normal use, due to defective material or work¬
manship, it will be replaced for the original user, in exchange
for the unserviceable battery, with an equivalent new battery at
an adjusted price. This adjusted price shall be determined by
applying to the then current retail price of the new battery, the
percentage of the maximum (24) units of service which was re¬
ceived from the unserviceable battery.
LIMITATIONS
No-charge replacements or adjustments under this policy may be
made by any authorized dealer.
This policy does not cover the following:
1. Unserviceability due to abuse or neglect, failure to maintain
recommended electrolyte level, fire wreckage, explosion, freez¬
ing, the addition to the battery of any chemical or solution other
than approved water or battery grade sulfuric acid of proper
gravity, the use of a group size smaller than the group size of
the original equipment battery, or continued operation of the
battery in an undercharged condition (below half charge -
1.190 sp. gr.).
2. Breakage of containers, covers or posts.
3. The cost of transportation, service calls, recharges or the use of
rental batteries.
Proof of date of purchase is required for all claims. This policy is
void if the date coding on the battery is removed or destroyed.
AE 5-73

CONTENTS
CONTENTS
TO OUR DEALER . 1
TO OUR CUSTOMER . 2
USER’S RESPONSIBILITY. 3
BATTERY SERVICE ADJUSTMENT POLICY . 3
SAFETY. 5 thru 10
SPECIFICATIONS. 11
GENERAL INFORMATION . 12,13
LUBRICATION AND SERVICE
Time Interval Chart forService Items . 16
Lubrication and Service Guide. 17
Front Axle . 18
3-Point Hitch . 18
Clutch-Brake Shaft Assembly. 18
Engine Cooling System . 19
Engine Oil Levels & Filters . 20
Engine Fuel Sediment Bowl & Filter. 20
Bleed Air from the Fuel System. 21
Front Wheel Bearings . 21
Transmissions Hydraulic System Oil
Level & Filter. 22
Front Axle Drive . 23
Battery. 23
Fuel Tank . 24
Air Cleaner . 24
Air Cleaner Element. 25
Alternator . 26
Injection Pump Lubrication . 26
Engine Service Tips. 27
Storage of Tractor . 27
OPERATING CONTROLS AND INSTRUMENTS
Instruments & Controls. 30 thru 34
OPERATION
StartingS Stopping the Engine . 36
Fast Warm-up Period . 36
Brake-in Period. 36
Engine Clutch Pedal . 37
GearShifting-Transmission . 37
Coasting . 37
Brakes . 38
PTO Shaft . 38
PTO Operating Instructions . 39
3-Point Hitch . 40,41
Tire Inflation. 42
Weighting the Tractor . 43
ADJUSTMENTS
Position Control Lever. 46
Rate of Lower . 46
PTO Shift Lever . 46
PTO Safety Start Switch . 46
Fan Belt. 47
Engine Clutch Pedal . 47
Brake Pedal. 48
Wheel Tread S Torque . 48
Front Wheel Bearings . 49
Seat . 50
WIRING DIAGRAM . 51
MISCELLANOUS OPTIONAL, S EXTRA EQUIPMENT
Reinstallation of Rops Protective Frame 54 thru 56
FrontWeights. 57
RearWeights . 58
METRIC INFORMATION . 60 thru 62
TORQUE CHART S CONVERSION CHART . 63
4

SAFETY MEANS
—USE YOUR HEAD to keep yourself and others safe!
— KNOW and FOLLOW the safety rules and procedures for the job at hand — Short¬
cuts lead to accidents.
—THINK about the job you are doing at all times! Routine work does not mean
routine thinking.
—BE ALERT to potential danger situations — Correct them yourself or have them
corrected.
-THE ONLY WAY IS THE SAFE WAY - Use your eyes to find safety hazards
before they find you.
NOTE: Some illustrations in this manual show units with optional equipment in¬
stalled. This optional equipment may be purchased from your local authorized
Dealer.
NOTE: Some photographs in this manual were taken of prototype models. Produc¬
tion models may vary in some detail.
A CAUTION: Some photographs in this manual may show shields or cover
panels removed for purposes of clarity. NEVER OPERATE Unit without all
shields and cover panels in place.

SAFETY
SAFETY PRECAUTIONS
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
This symbol is used to call your attention to safety precautions that should be follow¬
ed by the operator to avoid accidents. When you see this symbol - Heed Its Warning.
Many hours of lost time and much suffering is caused
by the failure to practice simple safety rules.
IT IS TOO LATE TO REMEMBER WHAT SHOULD
HAVE BEEN DONE AFTER THE ACCIDENT HAS
HAPPENED.
1. STUDY this Operator’s Manual. LEARN how to
use the tractor controls for safe operation.
2. TRACTOR should be operated only by those who
are responsible, have been instructed thoroughly
in tractor’s operation, and have been authorized
to operate it.
3. ONLY one person, the operator, should be permit¬
ted on tractor when tractor is in motion. NEVER
CARRY PASSENGERS.
4. USE the platform to get on and off the tractor.
5. START engine from operator’s seat only. PLACE
gear shift lever in NEUTRAL disengage engine
clutch and place PTO shift lever in DISENGAGED
(off) position to close starting circuit.
6. DO NOT by-pass the safety starting switches. If
they malfunction, check with your authorized
dealer and have proper repairs made.
7. BEFORE starting tractor in motion, look around
carefully to make sure no person or obstruction is
in your path of travel.
8. ALWAYS drive the tractor at safe speeds for the
type of ground it is traveling on. The rate of travel
on hillside or curves should be regulated so there
is no danger of tipping.
9. USE CARE when operating on steep grades to
maintain proper stability.
10. ALWAYS keep the tractor in gear when going
down hill. NEVER permit tractor to coast with
clutch disengaged or with transmission in
neutral.
11. DO NOT drive too close to the edge of a ditch or
creek.
12. BEFORE leaving tractor seat ALWAYS PLACE
TRANSMISSION SHIFT LEVER IN NEUTRAL,
disengage P.T.O., set brakes, and stop engine
unless specifically instructed in the Operator’s
Manual of some machine or attachment to do
otherwise.
13. NEVER start a P.T.O. driven machine without
making sure that no one is on it or close to it.
14. NEVER permit anyone to examine, clean, service,
or adjust the tractor or any equipment operated by
it UNTIL tractor engine is stopped
TRANSMISSION SHIFT LEVER IS IN NEUTRAL,
P.T.O. is disengaged, brakes are set, and ALL
moving parts have stopped.
15. NEVER leave equipment in raised position when
tractor is parked.
16. NEVER leave the tractor unattended without plac¬
ing TRANSMISSION SHIFT LEVER IN NEUTRAL,
setting brakes, disengaging P.T.O., stopping the
engine, and removing the key.
17. DO NOT pull from the rear axle, PULL ONLY from
the DRAWBAR and take up slack in a chain
slowly.
18. DANGER: NEVER, UNDER ANY
CIRCUMSTANCES, ATTEMPT TO PULL
ANYTHING FROM THE ADJUSTABLE UPPER
LINK, THE LIFT SHAFT, THE AXLE OR THE
LIFT ARMS. Hitch loads to tractor ONLY at the
drawbar except when pulling implements spe¬
cifically designed for an properly fastened by
three point hitch.
19. If the tractor drive wheels are stuck, BACK OUT
to prevent the tractor from upsetting.
20. Use the FLASHING WARNING LIGHTS when trav¬
eling on public roads day or night - unless pro¬
hibited by law.
21. ALWAYS make sure that an S.M.V. emblem is
VISIBLE from the rear when traveling on public
roads.
22. NEVER run the tractor engine in a closed building
without adequate ventilation, because the ex¬
haust fumes are very injurious to health.
23. DIESEL FUEL CAN BE DANGEROUS. NEVER fill
fuel tank when engine is running, when engine is
hot, while near an open flame or when operator is
smoking.
24. DO NOT fill fuel tank completely to the top if trac¬
tor is to be exposed to sun. Fuel will expand and
run over. Wipe up any spilled fuel.
25. Keep a FIRE EXTINGUISHER handy at all times.
6

SAFETY
26. DO NOT remove radiator cap until after engine
has cooled.
27. NEVER stand between tractor and drawn imple¬
ment while tractor is being backed to hitch.
28. DO NOT wear loose-fitting clothing that may be
blown or drawn into moving parts.
29. KEEP tractor and attachments in good operating
condition and keep safety devices in place. Use
guards as instructed in Operator’s Manual.
30. Provide a FIRST AID KIT. Treat all scratches,
cuts, etc., with the proper antiseptic immediately.
31. TRACTOR and attachments should be stopped
and inspected for damage after striking a foreign
object, and any damage should be repaired before
restarting and operating the equipment.
32. DO NOT change engine governor settings or over
speed engine.
33. A tractor roll-over can result in personal injury or
death. For your protection use of roll-over protec¬
tive structure and seat belt is recommended. Re¬
place seat belt when it becomes worn or frayed.
34. DO NOT use a seat belt if tractor is not equipped
with roll over protective devices.
35. ADD front weight for pulling heavy drawbar loads
or mounted tools.
36. ADD rear wheel weights for front loader operation
or other counterweight.
37. SET wheels as wide as practical for the job being
done and for BETTER stability.
38. DRIVE SLOWLY when pulling heavy wheeled
loads, especially if trailing vehicle has no brakes.
Towed loads that weigh more than the weight of
the tractor SHOULD BE equipped with an inde¬
pendent braking system.
39. LONG HAIR should be tied up short to prevent it
from becoming entangled in moving parts.
40. REPLACE damaged or lost safety decals
immediately.
41. ALWAYS lower fully to the ground any unit at¬
tached to the draft arms or supported by a remote
hydraulic cylinder, or else BLOCK IT SECURELY
at a workable height before inspecting, adjusting
or performing maintenance work.
42. NEVER use your hands to seek out escaping hy¬
draulic oil; use a small piece of cardboard or
wood. Hydraulic oil escaping under pressure can
have enough force to penetrate the skin. This can
cause serious personal injury. Hydraulic oil can
also infect a minor cut or other opening in the
skin. If injured by escaping hydraulic oil, seek
prompt medical attention.
43. KEEP HANDS away from leaks in high pressure
fuel lines. The finely atomized fuel can be ejected
with sufficient force to penetrate the skin. This
can cause serious personal injury. If injured by
escaping high pressure fuel, seek prompt medical
attention.
TAKE TIME FOR SAFETY
REMEMBER THAT SAFE OPERATION IS NO ACCIDENT
AVOID ACCIDENTS
BUILT-IN SAFETY FEATURES CAN BE EFFECTIVE
ONLY IF PROPERLY MAINTAINED AND UTILIZED.
7

SAFETY
_SAFETY AND OPERATIONAL DECALS
. CAUTION: The following safety and operational decals are placed at strategic positions on the tractor to
provide the operator with a continual reminder of safe operating practices. If they become damaged or lost
» replace them immediately. They may be obtained from your authorized Dealer. The part number and location
of decal on the tractor are listed undereach copy of decal.
No. 2099204 - Located on Position Control Lever Quadrant
A CAUTION
To PREVENT PERSONAL INJURY to
l it is YOUR RESPONSIBILITY to read, under¬
stand. and follow the safe operating practices
defined in the Operator s Manual shipped with
this tractor. If the manual is missing or damaged,
obtain a replacement from your local authorized
dealer.
2. FASTEN SEAT BELT securely if tractor has
ROPS.
3. REDUCE SPEED when turning, crossing slopes,
and on rough slick or muddy surfaces.
4.STAY OFF STEEP SLOPES.
5. WATCH WHERE YOU ARE GOING, especially at
row ends, on roads, and around trees.
6. NO RIDERS should be permitted on farm field
equipmenL
7.OPERATE TRACTOR SMOOTHLY-- no jerky starts
or stops.
8. HITCH ONLY TO DRAWBAR except when using
an implement designed for and properly fastened
by 3-point hitch.
9. AVOID DITCHES. EMBANKMENTS and HOLES
if possible, when operating tractor.
you or others, follow these instructions:
10 SET PARKING BRAKE or PARK LOCK whenever
tractor is stopped
11.KEEP ALL GUARDS IN PLACE when machinery
is in operation.
12.STOP ENGINE, disconnect the power source, and
WAIT FOR ALL MOVEMENT TO STOP BEFORE
SERVICING, adjusting, cleaning or unclogging
ANY EQUIPMENT unless specifically instructed
in an Operator's Manual to do otherwise.
13.NEVER COAST down hill.
14 MAKE SURE EVERYONE IS CLEAR of machinery
before starting engine, engaging power, or
operating the machine.
15. USE FLASHING WARNING LIGHTS when
operating on high ways except where prohibited
by law
16. NEVER TOW tractor with transmission in gear.
17. DO NOT FILL FUEL TANK while engine is
running, while engine is hot. near open flame
or while smoking.
No. 273992 -1 Used - Located on Top of L.H. Wheel Guard
A WARNING
To PREVENT PERSONAL INJURY
follow these instructions
1 KEEP ALL power take-off safety SHIELDS in PLACE
2 . This tractor is equipped with a 540 rpm PTO
Position and lock drawbar hitch hole 14 inches
(356 mm) from end of PTO shaft.
3. PULL ONLY FROM THE DRAWBAR except when
using an implement designed for and properly
fastened by 3-point hitch.
4. CAREFULLY CHECK OPERATION and maximum lift
height of any implement, especially 3-point hitch mount¬
ed backhoes. to insure proper clearance with ROPS
No. 271600 -1 Used - Located on R.H. Wheel Guard
8