Simpson Amik 301 User manual

USA SINCE 1936
RELIABILITY BEYOND MEASURE
®
Operating Manual
Amik 300 / 301
The Information contained in these installation instructions is for use only by installers trained to make electrical power installations and
is intended to describe the correct method of installation for this product. However, Company has no control over the field conditions
which influence product installation.
It is the user's responsibility to determine the suitability of the installation method in the user's field conditions. Company only
obligations are those in Company standard Conditions of Sale for this product and in no case will Company be liable for any other
incidental, indirect or consequential damages arising from the use or misuse of the products.

Cover Page 2

Section
Three Phase Touch Screen Digital Multi-fuction Meter
Installation & Operating Instructions
Contents
1. Introduction
2. Measurement Reading Screens
3. Programming
3.1 Password Protection
3.2 Menu selection
3.2.1 System Parameter selection screen
3.2.2 Communication Parameter selection screen
3.2.1.1 System type
3.2.1.2 Potential transformer Primary value
3.2.1.3 Potential transformer Secondary value
3.2.1.4 Current transformer Primary value
3.2.1.5 Current transformer Secondary valuealue
3.2.1.6 Demand integration time
3.2.1.7 Auto Scrolling
3.2.1.8 Low current noise cutoff
3.2.1.9 Energy On RS 485
3.2.1.10 Energy digit reset count
3.2.2 Address Setting
3.2.2.2 RS 485 Baud rate
1
3.2.2.3 RS 485 Parity selection
3.1.1 Change Password
Three Phase (3W/4W)

2
3.2.4.3 Parameter setting for Analog Output-1
3.2.4.4 Parameter setting for Analog Output-2
3.2.4 Output Option selection screen (menu)
3.2.3.1 Resetting Parameter
8. Number of Interruption
7. On - Hour.
6. Run - Hour.
5. Phase Rotation Error screen.
9. Analog Output
3.2.5 Brightness & Contrast
4. Touch screen calibration.
RS 485 (Modbus) output
User Assignable modbus Registers
11.1
11.
3.2.3 Reset Parameter selection screen

15. Specification
13. Installation
13.1
13.2 Case Dimensions and Panel Cut-out
13.3 Wiring
13.4 Auxilary Supply
13.5
Fusing
13.6
Earth / Ground Connections
14. Connection Diagrams
16. Connection for Optional RS 485 / Analog Output
12. Phaser Diagram
1. Introduction
This instrument is a panel mounted 96 x 96mm DIN Quadratic Digital metering system for the
measurement of important electrical parameters like AC voltage, AC Current, Frequency,
Power, Energy (Active / Reactive / Apparent). The instrument integrates accurate
measurement of technology (All Voltage & Current measurement are True RMS up to 15th
Harmonic) with 320x240 Pixels touch screen TFT LCD display.
This instrument can be configured and programmed at site for the following:
PT Primary, PT Secondary, CT Primary, CT Secondary (5A or 1A)
and 3 phase 3W or 3 Phase 4W system.
The front panel has a 3.5” Touch Screen through which the user can
move across the available measurement reading, reset the energy,
Min/Max (System Voltage and System Current) and configure the
product setting.
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
CT SECONDARY
OK
5 AMPERE
1 AMPERE
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
MAIN MENU
POWER ENERGY SETUP
VOLTAGESYSTEM CURRENT
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
CT SECONDARY
OK
5 AMPERE
1 AMPERE
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
MAIN MENU
POWER ENERGY SETUP
VOLTAGESYSTEM CURRENT
3
EMC installation Requirements

TABLE 1:
Measured Parameters
System Voltage
System Current
Frequency
Voltage VL1-N(4wire only)
Voltage VL2-N(4wire only)
Voltage VL3-N(4wire only)
Voltage VL1-L2
Voltage VL2-L3
Voltage VL3-L1
Current L1
Current L2
Current L3
Units of
Volts
Amps
Hz
Volts
Volts
Volts
Volts
Volts
Volts
Amps
Amps
Neutral Current ( 4 wire only ) Amps
Amps
Measurement
Active Import Energy (8 Digit resolution) kWh
kWh
Active Export Energy (8 Digit resolution)
Active Power (System / Phase (4 wire only) )
Reactive Power (System / Phase (4 wire only) )
Apparent Power (System / Phase (4 wire only) )
Power Factor (System / Phase (4 wire only) )
PhaseAngle ( Phase (4 wire only) )
Kwatts
KVAr
KVA
Degree
kVArh
Reactive Import Energy (8 Digit resolution) kVArh
Reactive Export Energy (8 Digit resolution) kVAh
Apparent Energy (8 Digit resolution)
Ampere Hour (8 Digit resolution)
KAh
4

Measured Parameters Units of
KW Import Demand
KW Export Demand
Max Current Demand
Max kVA Demand
Max KW Import Demand
Max KW Export Demand
Run Hour
On Hour
Number of Interruptions
Phase Reversal Indication ( 4 wire only )
KW
Amps
KVA
KW
KW
KW
Hours
Hours
Counts
Measurement
AmpsCurrent Demand
KVA Demand KVA
I1 THD
I2 THD
V1 THD*
V2 THD*
V3 THD*
%
I3 THD
System Voltage THD
System Current THD
%
%
%
%
%
%
%
Pictorial representation of Phaser Diagram (4 wire only)
Pictorial representation of Voltage Waveform
Pictorial representation of Current Waveform
Pictorial representation of VA Waveform per phase (4 wire only)
*Note : THD Parameters are L-N in case of 3P 4W & L-L in case of 3P 3W .
5

6
2. Measurement Reading Screens
In normal operation the user is presented with one of the measurement reading screens out of
several screens. These screens form particular submenu may be scrolled through one at a time
in incremental order by touching the “ key ” and in decremental order by touching “ key ”
on that screen. Viewing of any individual parameter with large reading (eg. shown
of Line to neutral Voltage L2 in sub meau 2 screen 13) is also possible by touching that
particular parameter.
Screen 2: System Max.
Screen 1: System Parameters
(System Voltage, System
Current, System Active Power)
SUBMENU 1: SYSTEM
KVA
Min
Angle
Max
KVAh
Ph Y
KWh
Ph B
%THD
Demand
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2 V
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2 V
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
V
0.000
0.000
SYSTEM Max. VALUE
SYSTEM
MAIN
A
V
239.9
5.005
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2 0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2 0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2 0.000
0.000
SYSTEM RUN HOUR
SYSTEM
MAIN
000001.19
hrs
Values (System Voltage,
Screen 4: Pictorial
VOLTAGE
MAIN
VL2 0.000
VOLTAGE
MAIN
VL2 0.000
VOLTAGE
MAIN
VL2 0.000
MAIN
Inductive
Capacitive Inductive
Capacitive
0
90
180
0
270
0
0
0
VL1
VL2
VL3
IL1
IL2
IL3
3
2
1
0.000
0.000
0.000
0.000
0.000
0.000
0.000
0.000
0.000
V
V
V
A
A
A
V/Div
A/Div
124.5
1.500
-P,+Q +P,+Q
-P,-Q
+P,-Q
SYSTEM
Representation of Phaser
Angle
Max
KWh
Ph B
Demand
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 0.000
0.000
0.000
SYSTEM PARAMETERS
SYSTEM
MAIN
239.6
5.001
3.592 A
V
KW
Screen 3: System
Min. Values (System Voltage,
System Current)
System Current)
V
KW
VBR
x1000
x1000
P.F.
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
V
0.000
0.000
0.000
SYSTEM Min. VALUES
SYSTEM
MAIN
A
V
239.2
4.998
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM ON HOUR
SYSTEM
MAIN
000005.18
hrs
Screen 5 :
System Run Hour Screen 6 :
System ON Hour
Diagram (For 4 wire only)

LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM INTERRUPTIONS
SYSTEM
MAIN
00000012
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM FREQUENCY
SYSTEM
MAIN
Hz
0.000
Screen 7 : Screen 8 :
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM POWER FACTOR
SYSTEM
MAIN
1.000
Screen 9 :
System Interruptions System Frequency System Power Factor
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM % THD
SYSTEM
MAIN
A
V %
%
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
SYSTEM POWER
SYSTEM
MAIN
kVA
kVAr
kW
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
PHASE SEQUENCE
SYSTEM
MAIN
L1-L2-L3
CONNECTIONS ARE CORRECT
Screen 10 :
System % THD Screen 11 :
System Power Screen 12 : Phase Sequence
( 4 wire only )
Correct
Phase Sequence
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
PHASE SEQUENCE
SYSTEM
MAIN
ERROR
NOTE : WRONG PHASE SEQUENCE.
PLEASE CHECK YOUR CONNECTIONS.
Phase Sequence Error
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
L2
L1
L3 V
VV
V
V
239.5
239.6
239.3
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGE
VOLTAGE
PHASE L2
239.6
V
BACK
Screen 13 : Line-Neutral Voltage
SUBMENU 2 : VOLTAGE
(For 4 wire only)
(Displayed after touching any where
Phase L2 Line-Neutral Voltage
in the L2 row shown in screen 13)
7

(In case of 4 wire) (In case of 3 wire)
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 0.000
0.000
0.000
VOLTAGE
MAIN
L23
L12
L31
0.000
0.000
0.000
LINE VOLTAGE THD
%
%
%
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
PHASE VOLTAGE % THD
VOLTAGE
MAIN
L2
L1
L3 %
%
%
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-LINE VOLTAGE
VOLTAGE
MAIN
L23
L12
L31 V
VV
V
V
415.1
414.9
415.2
Screen 15 : Phase Voltage THDScreen 14 :
SUBMENU 3 : CURRENT
Screen 18 : Neutral Current
Screen 17 : Line Current
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE CURRENT
CURRENT
MAIN
IL2
IL1
IL3 A
A
A
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
NEUTRAL CURRENT
CURRENT
MAIN
A
0.000
Screen 16 : Pictorial representation
through voltage submenu list)
(For 4 wire only)
of Voltage Waveform (Only accessed
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE CURRENT % THD
CURRENT
MAIN
IL2
IL1
IL3 %
%
%
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
L1 PHASE POWER
POWER
MAIN
kVA
kVAr
kW
0.000
0.000
0.000
Screen 19:
Line Current %THD
Screen 20 : Pictorial representation
(Only accessed through
of Current Waveform
current submenu list)
Screen 21 : L1 Phase Power
SUBMENU 4 : POWER
Reactive/Apparent/Active
(For 4 wire only)
8
Screen 15 : Line Voltage THD
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGE
VOLTAGE WAVEFORM
VOLTAGE
MAIN
49.94
Hz
2.500
ms/Div
62.25
V/Div
116.5
Vrms
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGECURRENT WAVEFORM
CURRENT
MAIN
49.94
Hz
2.500
ms/Div
30.00
A/Div
42.43
Arms
42.43
Arms
42.43
Arms
116.5
Vrms
116.5
Vrms
In
Line-Line Voltage

Screen 23 : L3 Phase Power
Reactive/Apparent/Active
(For 4 wire only)
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
L2 PHASE POWER
POWER
MAIN
kVA
kVAr
kW
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
L3 PHASE POWER
POWER
MAIN
kVA
kVAr
kW
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
PHASE ANGLE
POWER
MAIN
L2
L1
L3 DEG
DEG
DEG
0.000
0.000
0.000
Screen 24 : Phase Angle
(Phase L1/L2/L3) (for 4W only)
Screen 22 : L2 Phase Power
Reactive/Apparent/Active
(For 4 wire only)
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
POWER FACTOR
POWER
MAIN
L2
L1
L3
1.000
1.000
1.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
CURRENT DEMAND
POWER
MAIN
A
A
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
VA DEMAND
POWER
MAIN
kVA
kVA
0.000
0.000
Screen 25 : Power Factor
(Phase L1/L2/L3) (for 4W only)
Screen 26 :
Current Demand Screen 27 :
VA Demand
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
IMPORT ACTIVE DEMAND
POWER
MAIN
kW
kW
0.000
0.000
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGE
L1 PHASE WAVEFORM
POWER
MAIN
116.5
V
49.94
Hz
2.500
ms/Div
62.25
V/Div
42.43
A
210.4
DEG
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN VOLTAGE MAIN
EXPORT ACTIVE DEMAND
POWER
MAIN
kW
kW
0.000
0.000
Screen 28 :
Import Active Demand Screen 29 :
Export Active Demand
Screen 30 : Pictorial representation
(only accessed through power submenu list)
of L1 Phase Waveform (For 4 wire only)
9
Demand
Max
Demand Max
Demand
Max
Demand
Max
Demand
Demand
Demand
Demand

LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
REACTIVE ENERGY EXPORT
ENERGY
MAIN
0.0000000
kVArh
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
ACTIVE ENERGY IMPORT
ENERGY
MAIN
0.0000000
kWh
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGE
L2 PHASE WAVEFORM
POWER
MAIN
116.5
V
49.94
Hz
2.500
ms/Div
62.25
V/Div
42.43
A
210.4
DEG
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGE
L3 PHASE WAVEFORM
POWER
MAIN
116.5
V
49.94
Hz
2.500
ms/Div
62.25
V/Div
42.43
A
210.4
DEG
L2 Phase Waveform (For 4 wire only)
L3 Phase Waveform (For 4 wire only)
SUBMENU 5 : ENERGY
Screen 33 :
Active Energy Import
Screen 34 :
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
ACTIVE ENERGY EXPORT
ENERGY
MAIN
0.0000000
kWh
Screen 35 :
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
REACTIVE ENERGY IMPORT
ENERGY
MAIN
0.0000000
kVArh
Active Energy Export Reactive Energy Import Reactive Energy Export
Screen 36 :
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
0.000
0.000
0.000
APPARENT ENERGY
ENERGY
MAIN
0.0000000
kVAh
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
LINE-NEUTRAL VOLTAGE
VOLTAGE
MAIN
VL2
VL2
VL2
VL2 V
VV
V
V
0.000
0.000
0.000
AMPERE HOUR
ENERGY
MAIN
0.0000000
kAh
Screen 37 : Screen 38 :
Apparent Energy Ampere Hour
10
Screen 31 : Pictorial representation
Screen 32 : Pictorial representation
(only accessed through power submenu list) (only accessed through power submenu list)

11
AMPERE
HOUR
APPARENT
ENERGY
REACTIVE ENERGY
EXPORT
REACTIVE ENERGY
IMPORT
ACTIVE ENERGY
EXPORT
ACTIVE ENERGY
IMPORT
RESET
PARAMETERS
COMMUNICATION
MAIN MENU
SYSTEM
SYSTEM TYPE
PT PRIMARY
PT SECONDARY
CT PRIMARY
CT SECONDARY
DEMAND
NOISE CUTOFF
AUTO SCROLL
(Sec 3.2.1.1)
(Sec 3.2.1.2)
(Sec 3.2.1.3)
(Sec 3.2.1.4)
(Sec 3.2.1.5)
(Sec 3.2.1.7)
Parameter Screens
INTEGRATION
TIME
LOWCURR.
CURRENT
VOLTAGE
SYSTEM
Max. VOLTAGE
PHASER
RUN HOUR
A
A
FREQUENCY
SYSTEM
PARAMETERS
And CURRENT
Min. VOLTAGE
And CURRENT
ON HOUR
No. OF
INTERRUPTIONS
CT SECONDARY
DEMAND
NOISE CUTOFF
AUTO SCROLL
(Sec 3.2.1.5)
(Sec 3.2.1.7)
INTEGRATION
TIME
LOWCURR.
POWER FACTOR
SEQUENCE *
PHASE
SYSTEM
POWER
THD.VOLTAGE
AND CURRENT
(Sec 3.2.2.3)
VOLTAGE
% THD
Line Current
Neutral Current *
OPTIONS
(Sec 3.2.4)
POWER
CHANGE
PASSWORD
(Sec 3.1)
ENERGY
AA
A
B
A
B
LINE CURRENT
% THD
DIAGRAM *
Line to Line
VOLTAGE
Line to Neutral *
VOLTAGE
NOTE:SCREENS MARKED WITH * ARE AVAILABLE
(Sec 3.2.2.3)
(Sec 3.2.2.3)
WAVEFORM
VOLTAGE
WAVEFORM
CURRENT
L3 PHASE
WAVEFORM *
L2 PHASE
WAVEFORM *
L1 PHASE
WAVEFORM *
EXPORT
ACTIVE DEMAND
IMPORT
ACTIVE DEMAND
APPARENT
DEMAND
CURRENT
DEMAND
PHASE
POWER FACTOR *
L3 PHASE
POWER *
L2 PHASE
POWER *
L1 PHASE
POWER *
PHASE
ANGLE *
ONLY IN 4W SYSTEM (NOT IN 3 WIRE SYSTEM)

12
Rs485 ADDRESS
(Sec 3.2.2.1)
ANALOG OUTPUT 1
(Sec 3.2.4.3)
ANALOG OUTPUT 2
selection)
(Acc. To Table2)
(Sec 3.2.4.4)
ANALOG OUTPUT 2
(Analog 2 parameter
RS485 PARITY
(Sec 3.2.2.3)
PT PRIMARY
(Sec 3.2.1.2)
PT SECONDARY
(Sec 3.2.1.3)
CT PRIMARY
(Sec 3.2.1.4)
CT SECONDARY
(Sec 3.2.1.5)
AUTO SCROLL
(Sec 3.2.1.7)
NOISE CUTOFF
(Sec 3.2.1.8)
LOWCURR.
RS485
(Sec 3.2.2.2)
BAUD RATE
RS485
(Sec 3.2.2.2)
BAUD RATE
ANALOG OUTPUT 1
(Analog 1 parameter
selection)
(Acc. To Table 2)
DEMAND
(Sec 3.2.1.6)
INTEGRATION
TIME
RESET MAX VOLTAGE & CURRENT
RESET MIN VOLTAGE & CURRENT
RESET RUN-HOUR,ON-HOUR
RESETAUX INTERRUPT COUNT
Select any option by
RESETALL
PASSWORD
SYSTEM
(Sec 3.2.1)
Setup Parameter Screens
PARAMETERS
ENTER
SYSTEM
(Sec 3.2.1)
PARAMETERS
PARAMETERS
COMMUNICATION
(Sec 3.2.2)
PARAMETERS
(Sec 3.1)
SYSTEM TYPE
(Sec 3.2.1.1)
BRIGHTNESS
& CONTRAST
(Sec 3.2.5)
CHANGE
PASSWORD
(Sec 3.1.1)
RESET
(Sec 3.2.3)
PARAMETERS
OPTIONS
OUTPUT
(Sec 3.2.4)
touching on it.
RESET DEMAND PARAMETERS
RESET ALL ENERGIES
RS485
(Sec 3.2.1.9)
ENERGYON
RESETCOUNT
(Sec 3.2.1.10)
ENERGYDIGIT

3.1. Password Protection
Password protection can be enabled to prevent unauthorised access to set-up screens, by default
password is “0000”.
Password protection is enable by selecting any four digit number.
3. Programming
The following sections comprise step by step procedures for configuring the instrument for
individual user requirements.
To access the set-up screens touch on the “ SETUP ” icon in Main Menu. This will take the
User into the Password Protection Stage(Section 3.1).
After touching “ SETUP” icon Password protection screen is
displayed. Screen consists of 0 to 9 digit input keypad for entering
the password very similar to any calculator in touchscreen mobile.
“Enter Password” is displayed on screen at start so that user can
enter password using displayed keypad.
Touching “ key ” will display 1 in display area, similary user can
enter remaining 3 digits.
For deleting any digit while entering password, user can touch
“ key”.
1
DEL
SETUP
ENTER PASSWORD
123
456
789
0BACK
DEL
ENTER
SETUP
1
13
123
456
789
0BACK
DEL
ENTER

After entering the complete password user needs to confirm password
by touching “ key”.
ENTER
SETUP
1234
If Entered password is correct then “Password Accepted” is displayed
on screen & user will enter into setup menu.
Password confirmed.
SETUP
PASSWORD ACCEPTED
If Entered password is wrong then Password“ Rejected” is displayed
on screen & user need to re-enter the password
Password Incorrect.
SETUP
PASSWORD REJECTED.
After wrong password is entered, user needs to touch “ key” for
trying another password. ENTER
PASSWORD
PRESS ENTER TO TRY AGAIN
14
123
456
789
0BACK
DEL
ENTER
123
456
789
0BACK
DEL
ENTER
123
456
789
0BACK
DEL
ENTER
123
456
789
0BACK
DEL
ENTER

Change Password Option is the second last option in list of “SETUP”
submenu, so can be accessed by a simple touch anywhere in “Change
Password” row.
In this screen user first need to enter the current password.
3.1.1 Change Password
PASSWORD
ENTER CURRENT PASSWORD
& now user can enter the new 4 digit password.
After input of correct password,“PASSWORD ACCEPTED”is displayed
PASSWORD
ENTER NEW PASSWORD
PASSWORD
PASSWORD CHANGED
After entering new password user needs to touch “
After confirming “PASSWORD CHANGED” is displayed on
screen, which ensures successful changing of the password.
ENTER
New Password confirmed.
key” to confirm.
3.2 Menu selection.
After entering in the SUBMENU 6 - SETUP, user will be asked to enter password & after input of
correct password list of following parameters will be displayed on screen :-
3.2.1 SYSTEM PARAMETERS
3.2.2 COMMUNICATION PARAMETERS
15
123
456
789
0BACK
DEL
ENTER
123
456
789
0BACK
DEL
ENTER
123
456
789
0BACK
DEL
ENTER

Touching on SYSTEM PARAMETER will open the system parameters list screen. Then these
screens from particular parameter may be scrolled through one at a time in incremental order by
touching the “ key” and in decremental order by touching “ key” on given touch screen.
3.2.1 System Parameters Selection
After entering in the “SYSTEM PARAMETERS”, List of following parameters will be display :-
3.2.1.1 SYSTEM TYPE
3.2.1.2 PT PRIMARY(L-L)
3.2.1.3 PT SECONDARY(L-L)
3.2.1.4 CT PRIMARY
3.2.1.5 CT SECONDARY
3.2.1.6 DEMAND INTEGRATION TIME
3.2.1.7 AUTO SCROLL
3.2.1.8 LOW CURRENT NOISE CUTOFF
3.2.3 RESET PARAMETERS
3.2.4 OUTPUT OPTIONS
3.2.5
BRIGHTNESS & CONTRAST
3.2.1.1 System Type
LINE-NEUTRAL VOLTAGE
VL2
VL2
VL2
VL2
0.000
LINE-NEUTRAL VOLTAGE
VL2
VL2
VL2
VL2
0.000
LINE-NEUTRAL VOLTAGE
VL2
VL2
VL2
VL2
0.000
SYSTEM TYPE
3-PHASE 4 WIRE
FOR 3 PHASE STAR CONNECTED LOAD
3-PHASE 3 WIRE
FOR 3 PHASE DELTA CONNECTED LOAD
MAINMAINMAINMAINMAINMAIN
OK BACK
This screen is used to set the system type.
Two types: 3 phase 3 wire & 3 phase 4 wire system are displayed
on screen. Touching radio buttom in front of particular type will select
that type.
Touch on “ key” will confirm the system type.
Touching the “ key” will keep the old selected setting and will
return to previous menu.
OK
BACK
16
Note : If system type is changed, relay parameter selection & analog output
selection will be set to NONE.
3.2.1.9 ENERGY ON RS485
3.2.1.10 ENERGY DIGIT RESET COUNT

3.2.1.2 Potential Transformer Primary Value
The nominal full scale voltage will be displayed as Line to Line Voltages for all system types.
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGEPT PRIMARY
ENTER PT PRIMARY VALUE(L-L)
This screen can be accessed only from system parameters list menu.
Here again 0 to 9 digit input keypad is provided to set value of PT
Primary, & user can confirm this value with a simple touch “
key”. “ key” is used to multiply value by 1000.
ENTER
phase, “Invalid value” will be displayed. Then the valid range will be displayed.
K
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGEPT PRIMARY
INVALID VALUE
Valid range of PT primary setting value is from
If value outside the range is entered, It will display “INVALID VALUE”
followed by correct range of parameter
.
100 VL-L to 692.8 KVL-L.
3.2.1.3 Potential Transformer secondary Value
The value must be set to the nominal full scale secondary voltage which will be obtained from the
the Transformer when the potential transformer(PT)primary is supplied with the voltage defined
in 3.2.1.2 potential transformer primary voltage. The ratio of full scale primary to full scale
secondary is defined as the transformer ratio.
Secondary, & user can confirm this value with a simple touch on
“ key”.
This screen can be accessed only from system parameters list menu.
Here again 0 to 9 digit input keypad is provided to set value of PT
ENTER
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGEPT SECONDARY
ENTER PT SECONDARY VALUE(L-L)
17
1 2 3
456
78 9
DEL
ENTER
0KBACK
1 2 3
456
7 8 9
DEL
ENTER
0KBACK
1 2 3
456
7 8 9
DEL
ENTER
0BACK
In case presently displayed Potenial Transformer Primary value
together with the Current Transformer Primary value, previously set,
would result in a maximum power of greater than 666.6 MVA per

3.2.1.4 Current Transformer Primary Value
The nominal Full Scale Current that will be displayed as the Line currents. This screen
enables the user to display the Line currents inclusive of any transformer ratios, the values
displayed represent the Current in Amps.
Potential Transformer secondary ranges for various Input Voltages
110V L-L (63.5V L-N) 100 - 120V L-L (57.73V - 69.28V L-N)
121 - 240V L-L (69.86V - 138.56V L-N)
241 - 480V L-L (139.14V - 277.12V L-N)
230V L-L (133.0V L-N)
415V L-L (239.6V L-N)
Valid range of PT secondary setting value is from 241.0 to 480.0.
for 415 VL-L. Please refer the table bellow for different ranges.
If value outside the range is entered, It will display “INVALID VALUE”
followed by correct range of parameter
.
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGEPT SECONDARY
INVALID VALUE
In case presently displayed Current Transformer Primary Value
together with the Potential Transformer Primary Value results in a
maximum power of greater than 666.6 MVA, “invalid value” will be displayed. Example:
If primary value of PT is set as 692.8kV L-L (max value) then primary value of Current is
restricted to 1157A.
The “Maximum Power” restriction of 666.6 MVA refers to 120% of nominal current and
120% of nominal voltage, i.e, 462.96 MVA nominal power per phase.
LINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGELINE-NEUTRAL VOLTAGECT PRIMARY
ENTER CT PRIMARY VALUE
Here again 0 to 9 digit input keypad is provided to set value of CT
Primary & user can confirm this value with a simple touch on “
key”. “ key” is used to multiply value by 1000.
This screen can be accessed only from system parameters list menu.
ENTER
K
18
1 2 3
456
7 8 9
DEL
ENTER
0BACK
1 2 3
456
7 8 9
DEL
ENTER
0KBACK