Sinbo SHC 4365 User manual

SHC 4365 RECHARGEABLE HAIR TRIMMER
INSTRUCTION MANUAL
EN
RU

- 1 -
ENGLISH
SINBO SHC 4365
RECHAREABLE HAIR TRIMMER
INSTRUCTION MANUAL
TECHNICAL SPECIFICATIONS
Power: 3W
Voltage: AC230V,50HZ
PRODUCT FEATURES
* High quality stainless steel blade,
* Powerful rotary motor
* On/off switch
* Power cord charger
* Including cleaning brush, oil, guide comb
* Built in Ni-Cd battery 1*600mA
PREPARING FOR USE
1. The appliance as supplied by the manufacture is not yet ready for use. It must be
electrically charged prior to use.
2. Insert the plug of charger into a socket. Warning! This appliance must be charged at
the specified voltage (AC230V 50Hz). While the appliance is being charged, the switch
must be set at “0” (the “0” must be visible). A charging period of 16 hours is required
before initial use.
3. After charging the appliance is ready for use. It can be used with or without the clip-
on comb attachment. To attach the clip-on comb attachment, slide it onto the cutting
head until it clicks into position. The appliance must be switched off while the clip-on
comb attachment is being attached or removed.
4. The clip-on comb attachment is easily adjustable. Simply slide it up or down the cutting
head. The hair can be cut to 4 different lengths ranging from approximately 3 mm to 6
mm. The position of the clip-on comb attachment on the cutting head determines the
length of the haircut.
5. After using the appliance, switch it off. In order to retain the load capacity of the storage
battery we recommend to use the storage battery until it is empty before reloading.
REPLACING THE CUTTING HEAD
Switch the appliance off before replacing the cutting head!
If the performance of the appliance deteriorates after extended use, despite regular
cleaning and maintenance, the cutting head should be replaced (the cutting head can be
ordered as a spare part from the Service Department).

- 2 -
CLEANING AND MAINTEN-ANCE OF THE APPLIANCE
Switch the appliance off before cleaning or carrying out maintenance!
In order to ensure that the appliance remains in perfect working order, it it important
to note the following instructions:
In order to retain the load capacity of the storage battery we recommend to use the
storage battery until it is empty before reloading.
Wipe the appliance with a cloth only (which may be slightly damp, if necessary). No
solvents or lubricants may be used.
After use, take off the clip-on comb attachment and remove any residual hair from the
cutting head with a cleaning brush.
In order to ensure good cutting results and a long life, it is important to oil the cutting
head frequently.
PLEASE ALSO NOTE THE FOLLOWING
- During charging, the clipper should be placed in a position where there is no contact
with moisture, water or other liquids possible.
- Never try to remove foreign bodies from the inside of the clipper with a pointed tool
(e.g. Tail comb).
- Always switch off the clipper before putting it down and between cutting operations.
- Protect the cable from damage. Do not pull the cable. If the cable should become
damaged, contact the Service Department. The battery charging stand can be ordered
as a spare part from the Service Department.
- Do not allow the cable to come into contact with hot surfaces.
Do not touch the moving blades whilst the clipper is switched on.
- Do not use the clipper if the cutter set is damaged or broken, otherwise injuries could
occur.
- The appliance should not be exposed to temperatures below 0? or above +40? for any
great length of time. Avoid exposure to direct sunlight.
- Always turn the appliance off while it is being recharged (the “0” must be visible).
- Electrical appliances are not children’s toys. Never allow a child to touch electrical
equipment.
If any problems or irregularities arise while the appliance is being used it must be
switched off and the plug should be pulled out of the socket. Send the complete clipper
with the adapter the Service Department to be checked.
DISPOSING OF THE BATTERY
When you discard your shaver in due course, please remove the battery. Do not throw
the battery away with the normal household waste. But hand it in separately at an officially
assigned collection point.

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -
11-2017

Made in China
Produced at: 11-2017
Deima Elektromekanik A.S.
Cihangir Mh. Guvercin Cd.
No:4 Avcilar-ISTANBUL-TURKEY
11-2017
Cihangir Mh. Guvercin Cd. No:4 Avcilar-ISTANBUL-TURKEY
Deima Elektromekanik A.S.