Sinclair ASC-60AN User manual

USER'S MANUAL
ASC-60AN
UNI ON/OFF SERIES

„Original instruction“

INDOOR UNIT
OUTDOOR UNIT
Fig.1
Air flow louver(at air outlet) Air-in grill
Drain pump(drain water from indoor unit) Display panel
Drain pipe Remote controller
Air outlet Refrigerant pipe
Air filter(inside air-in grill) Air inlet
Air inlet Air outlet
NOTE
All the pictures in this manual are for explanation purpose only. They may be slightly different from the air conditioner
you purchased(depend on model).The actual shape shall prevail.

1.IMPORTANTSAFETY
INFORMATION
To prevent injury to the user or other people and
property damage, the following instructions must be
followed. Incorrect operation due to ignoring of
instructions may cause harm or damage.
The safety precautions listed are divided into two
categories. In either case, important safety information is
listed which must be read carefully.
WARNING
Failure to observe a warning may result in death. The
appliance shall be installed in accordance with national
wiring regulations.
CAUTION
Failure to observe a caution may result in injury or damage
to the equipment.
WARNING
Ask your dealer for installation of the air conditioner.
Incomplete installation performed by yourself may result in
a water leakage, electric shock, and fire.
Ask your dealer for improvement, repair, and
maintenance.
Incomplete improvement, repair, and maintenance may
result in a water leakage, electric shock, and fire.
In order to avoid electric shock, fire or injury, or if you
detect any abnormality such as smell of fire, turn off
the power supply and call your dealer for instructions.
Never let the indoor unit or the remote controller get
wet.
It may cause an electric shock or a fire.
Never press the button of the remote controller with a
hard, pointed object.
The remote controller may be damaged.
Never replace a fuse with that of wrong rated current
or other wires when a fuse blows out.
Use of wire or copper wire may cause the unit to break
down or cause a fire.
It is not good for your health to expose your body to
the air flow for a long time.
Do not insert fingers, rods or other objects into the air
inlet or outlet.
When the fan is rotating at high speed, it will cause injury.
Never use a flammable spray such as hair spray,
lacquer or paint near the unit.
It may cause a fire.
Never touch the air outlet or the horizontal blades
while the swing flap is in operation.
Fingers may become caught or the unit may break down.
Never put any objects into the air inlet or outlet.
Objects touching the fan at high speed can be dangerous.
Never inspect or service the unit by yourself.
Ask a qualified service person to perform this work.
Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact you local government for information regarding the
connection systems available.
If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundeater and get into the food chain, damaging
your health and well-being.
To prevent refrigerant leak, contact your dealer.
When the system is installed and runs in a small room, it is
required to keep the concentration of the refrigerant, if by
any chance coming out, below the limit. Otherwise, oxygen
in the room may be affected, resulting in a serious
accident.
The refrigerant in the air conditioner is safe and
normally does not leak.
If the refrigerant leaks in the room, contact with a fire of a
burner, a heater or a cooker may result in a harmful gas.
Turn off any combustible heating devices, ventilate
the room, and contact the dealer where you purchased
the unit.
Do not use the air conditioner until a service person
confirms that the portion where the refrigerant leaks is
repaired.
CAUTION
Do not use the air conditioner for other purposes.
In order to avoid any quality deterioration, do not use the
unit for cooling precision instruments, food, plants, animals
or works of art.
Before cleaning, be sure to stop the operation, turn
the breaker off or pull out the supply cord.
Otherwise, an electric shock and injury may result.
In order to avoid electric shock or fire, make sure that
an earth leak detector is installed.
Be sure the air conditioner is grounded.
In order to avoid electric shock, make sure that the unit is
grounded and that the earth wire is not connected to gas
or water pipe, lightning conductor or telephone earth wire.
In order to avoid injury, do not remove the fan guard
of the outdoor unit.
Do not operate the air conditioner with a wet hand.
An electric shock may happen.
Do not touch the heat exchanger fins.
These fins are sharp and could result in cutting injuries.
Do not place items which might be damaged by
moisture under the indoor unit.
Condensation may form if the humidity is above 80%, the
drain outlet is blocked or the filter is polluted.

After a long use, check the unit stand and fitting for
damage.
If damaged, the unit may fall and result in injury.
To avoid oxygen deficiency, ventilate the room
sufficiently if equipment with burner is used together
with the air conditioner.
Arrange the drain hose to ensure smooth drainage.
Incomplete drainage may cause wetting of the building,
furniture etc.
Never touch the internal parts of the controller.
Do not remove the front panel. Some parts inside are
dangerous to touch, and a machine trouble may happen.
Never expose little children, plants or animals directly
to the air flow.
Adverse influence to little children, animals and plants may
result.
Do not allow a child to mount on the outdoor unit or
avoid placing any object on it.
Falling or tumbling may result in injury.
Do not operate the air conditioner when using a room
fumigation - type insecticide.
Failure to observe could cause the chemicals to become
deposited in the unit, which could endanger the health of
those who are hypersensitive to chemicals.
Do not place appliances which produce open fire in
places exposed to the air flow from the unit or under
the indoor unit.
It may cause incomplete combustion or deformation of the
unit due to the heat.
Do not install the air conditioner at any place where
flammable gas may leak out.
If the gas leaks out and stays around the air conditioner, a
fire may break out.
The appliance is not intended for use by young
children or infirm persons without supervision.
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Children should be supervised to ensure that they do
not play with the appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Do not operate your air conditioner in a wet room such
as a bathroom or laundry room.
2. PARTS NAMES
The air conditioner consists of the indoor unit, the
outdoor unit, the connecting pipe and the remote
controller. (See Fig.1)
Function indicators on indoor unit
display panel
Temporary button Infrared signal receiver
Display panel Fig.2-1
This function is used to operate the unit temporarily in
case you misplace the remote controller or its batteries are
exhausted. Two modes including AUTO and FORCED
COOL can be selected through the TEMPORARY
BUTTON on the air-in grill control box of the indoor unit.
Once you push this button, the air conditioner will run in
such order: AUTO, FORCED COOL, OFF, and back to
AUTO.
1 AUTO
The OPERATION lamp is lit, and the air conditioner will
run under AUTO mode. The remote controller operation is
enabled to operate according to the received signal.
2 FORCED COOL
The OPERATION lamp flashes, the air conditioner will turn
to AUTO after it is enforced to cool with a wind speed of
HIGH for 30 minutes. The remote controller operation is
disabled.
3 OFF
The OPERATION lamp goes off. The air conditioner is
OFF while the remote controller operation is enabled.
3. AIR CONDITIONER OPERATIONS AND
PERFORMANCE
Use the system in the following temperature for safe
and effective operation. The Max operation
temperature for the air conditioner (Cooling/Heating).
Temperature/
Mode
Outdoor
temperature Room temperature
Cooling operation 18°C ~ 43°C 17°C ~ 32°C
Heating operation -7°C ~ 24°C 0°C ~ 30°C
Dry operation 18°C ~ 43°C 17°C ~ 32°C
Table 3-2
Operation lamp
Timer indicator Alarm indicator
PRE-DEF indicator(cooling and heating type) or fan only
indicator(cooling only type)

NOTE
1 If air conditioner is used outside the above
conditions, it may cause the unit to function
abnormally.
2 The phenomenon is normal that the surface of air
conditioning may condense water when the
relative larger humidity in room, please close the
door and window.
3 Optimum performance will be achieved within
these operating temperature range.
■Three-minute protection feature
A protection feature prevents the air conditioner from being
activated for approximately 3 minutes when it restarts
immediately after operation.
■Power failure
Power failure during operation will stop the unit completely.
• The OPERATION lamp on the indoor unit will start
flashing when power is restored.
• To restart operation, push the ON/OFF button on the
remote controller.
• Lightning or a car wireless telephone operating nearby
may cause the unit to malfunction.
Disconnect the unit with the power and then connect the
unit with the power again. Push the ON/OFF button on the
remote controller to restart operation.
■Refrigerant Leakage Detection(optional):
With this new technology, the display area will appear EC
(if applicable) and the LED indication lamps continue
flashing when the outdoor unit detects refrigerant leakage.
■Louver Angle Memory Function(optional):
For some models, the machine is special designed with
louver angle memory function. Power failure during
operation or pressing the ON/OFF button on the remote
controller will stop the unit completely. When the power
restores or pressing the ON/OFF button on the remote
controller again, the unit restarts automatically with the
previous open angle of the horizontal louver by the
memory function. So we strongly recommend that the
open angle of the horizontal louver should not be set too
small, in case the condensed water forms and drops from
the horizontal louver. Press the Manual control button and
the open angle of the horizontal louver will be restored to
the standard angle.
4. HINTS FOR ECONOMICAL OPERATION
The following should be noticed to ensure an
economical operation.
Adjust the air flow louver properly and avoid direct air
flow to room inhabitants.
Adjust the room temperature properly for a
comfortable environment. Avoid excessive heating or
cooling.
Prevent direct sunlight during cooling operation by
using curtains or blinds.
Ventilate often. Extended use requires special
attention to ventilation.
Keep doors and windows closed. If the doors and
windows remain open, air will flow out of your room
causing a decrease in the cooling or heating effect.
Never place objects near the air inlet or the air outlet
of the unit. It may cause deterioration in the effect or
stop the operation.
Set the timer .
If you don't plan to use the unit for a long time, please
take the batteries from the remote controller. When
the power is on, some energy will be consumed, even
if the air conditioner isn't in operation. So please
disconnect the power to save energy.
Keep the indoor unit and remote controller at least 1
m away from televisions, radios, stereos, and other
similar equipment. Failing to do so may cause static
or distorted pictures.
A dirty air filter will reduce cooling or heating
efficiency, please clean it once two weeks.
5. ADJUSTING AIR FLOW DIRECTION
While the unit is in operation, you can adjust the air
flow louver to change the flow direction and naturalize
the room temperature evenly. Thus you can enjoy it
more comfortably.
Adjust it up and down Fig 5-1
Adjust it up and down Fig 5-2
■Set the air flow direction.
Press the SWING button to adjust the louver to the desired
position and press this button again to maintain the louver
at this position.
■Adjust the air flow direction automatically.
Press the SWING button, the louver will swing
automatically. While this function is set, the swing fan of
indoor unit runs; otherwise, the swing fan doesn't run. The
swing scale of every side is 30°. When the air conditioner
isn't in operation (including when TIMER ON is set), the
SWING button will be invalid.
6. MAINTENANCE
CAUTION
Before you clean the air conditioner, be sure the power
supply is off.
Check if the wiring is not broken off or disconnected.
Use a dry cloth to wipe the indoor unit and remote
controller.
A wet cloth may be used to clean the indoor unit if it is very
dirty.
Never use a damp cloth on the remote controller.
Do not use a chemically-treted duster for wiping or leave
such material on the unit for long.
it may damage or fade the surface of the unit.
Do not use benzine, thinner, polishing powder, or similar
solvents for cleaning.
These may cause the plastic surface to crack or deform.
■Maintenance after a long stop period
(eg. at the beginning of the season)
Check and remove everything that might be blocking inlet
and outlet vents of indoor units and outdoor units.
Clean air filters and casings of indoor units.
Refer to "Cleaning the air filter" for details on how to
proceed and make sure to install cleaned air filters back in
the same position.
Turn on the power at least 12 hours before operating the
unit in order to ensure smoother operation. As soon as he

power is turned on, the remote controller displays appear.
■Maintenance before a long stop period
(eg. at the end of the season)
Let the indoor units run in fan only operation for about half
a day in order to dry the interior of the units.
Clean air filters and casings of indoor units. Refer to "
Cleaning the air filter" for details on how to proceed and
make sure to install cleaned air filters back in the same
position.
■Cleaning the air filter
The air filter can prevent the dust or other particulate from
going inside. In case of blockage of the filter, the working
efficiency of the air conditioner may greatly decrease .
Therefore, the filter must be cleaned once two weeks
during long time usage.
If the air conditioner is installed in a dust place, clean the
air filter frequent.
If the accumulated dust is too heavy to be cleaned, please
replace the filter with a new one(replaceable air filter is an
optional fitting).
1 Open the air-in grill
Push the grill switches towards the middle simultaneously
as indicated in Fig.6-1. Then pull down the air-in grill.
The control box cables ,which are originally connected with
the main body electrical terminators must be pulled off
before doing as indicated above.
2 Take out the air-in grill (together with the air filter
shown in (Fig.6-1).
Pull the air-in grill down at 45 and lift it up to take out the
grill.
3 Dismantle the air filter.
4 Clean the air filter
Vacuum cleaner or pure water may be used to clean the
air filter. If the dust accumulation is too heavy , please use
soft brush and mild detergent to clean it and dry out in cool
place.
•The air-in side should face up when using vacuum
cleaner. (See Fig. 6-3)
•The air-in side should face down when using water. (See
Fig. 6-4)
CAUTION
Do not dry out the air filter under direct sunshine or with
fire.
5 Re-install the air filter.
6 Install and close the air-in grill in the reverse
order of step 1 and 2 and connect the control box cables to
the corresponding terminators of the main body .
Fig.6-1
Fig.6-2
Fig.6-3
Fig.6-4
7. FOLLOWING SYMPTOMS ARE NOT AIR
CONDITIONER TROUBLES
Symptom 1: The system does not operate
■The air conditioner does not start immediately after the
ON/OFF button on the romote controller is pressed.
If the operation lamp lights, the system is in normal
condition.To prevent overloading of the compressor motor,
the air conditioner starts 3 minutes after it is turned ON.
■If the operation lamp and the "PRE-DEF
indicator(cooling and heating type) or fan only
indicator(cooling only type)" light, it means you choose the
heating model, When just starting, if the compressor has
not started, the indoor unit appears "anti cold wind"
protection because of its overlow outlet temperature.
Symptom 2: Change into the fan mode during cooling
mode
■In order to prevent the indoor evaporator frosting, the
system will change into fan mode automatically, restore to
the cooling mode after soon.
■When the room temperature drops to the set
temperature, the compressor goes off and the indoor unit
changes to fan mode; when the temperature rises up, the
compressor starts again. It is same in the heating mode.
Symptom 3: White mist comes out of a unit
Symptom 3.1: Indoor unit
■When humidity is high during cooling operation If the
interior of an indoor unit is extremely contaminated, the
temperature distribution inside a room becomes uneven. It
is necessary to clean the interior of the indoor unit. Ask
your dealer for details on cleaning the unit. This operation
requires a qualified service person
Symptom 3.2: Indoor unit, outdoor unit
■When humidity is high during cooling operation If the
interior of an indoor unit is extremely contaminated, the
temperature distribution inside a room becomes uneven. It
is necessary to clean the interior of the indoor unit. Ask
your dealer for details on cleaning the unit. This operation
requires a qualified service person.
■When the system is changed over to heating operation
after defrost operation Moisture generated by defrost
becomes steam and is exhausted.

Symptom 4: Noise of air conditioners cooling
Symptom 4.1: Indoor unit
■A continuous low "shah" sound is heard when the
system is in cooling operation or at a stop.
When the drain pump (optional accessories) is in
operation,this noise is heard.
■A "pishi-pishi" squeaking sound is heard when the
system stops after heating operation.
Expansion and contraction of plastic parts caused by
temperature change make this noise.
Symptom 4.2: Indoor unit, outdoor unit
■A continuous low hissing sound is heard when the
system is in operation.
This is the sound of refrigerant gas flowing through both
indoor and outdoor units.
A continuous low hissing sound is heard when the system
is in operation.
This is the sound of refrigerant gas flowing through both
indoor and outdoor units.
■A hissing sound which is heard at the start or
immediately after stopping operation or defrost operation.
This is the noise of refrigerant caused by flow stop or flow
change.
Symptom 4.3: Outdoor unit
■When the tone of operating noise changes. This noise is
caused by the change of frequency.
Symptom 5: Dust comes out of the unit
■When the unit is used for the first time in a long time.
This is because dust has gotten into the unit.
Symptom 6: The units can give off odors
■The unit can absorb the smell of rooms, furniture,
cigarettes, etc., and then emit it again.
Symptom 7: The outdoor unit fan does not spin.
■During operation. The speed of the fan is controlled in
order to optimize product operation.
8. TROUBLESHOOTING
8.1 Troubles and causes of air conditioner
If one of the following malfunctions occur, stop operation,
shut off the power, and contact with your dealer.
■The operation lamp is flashing rapidly (5Hz).
This lamp is still flashing rapidly after turn off the power
and turn on again. (See in Table 8-1)
■Remote controller receives malfunction or the button
does not work well.
■A safety device such as a fuse, a breaker frequently
actuates.
■Obstacles and water enter the unit.
■Water leaks from indoor unit.
■Other malfunctions.
If the system does not properly operate except the above
mentioned cases or the above mentioned malfunctions is
evident, investigate the system according to the following
procedures. (See in Table 8-2)
8.2 Troubles and causes of remote controller
Before asking for serving or repairing, check the following
points. (See in Table 8-3)
NO. Malfunction running lamp timer lamp defrosting lamp alarm lamp display (nixie
tube)
1 In-outdoor unit communication checking
channel is abnormal Quick-flash Quick-flash E1
2 Room temperature sensor checking
channel is abnormal Quick-flash E2
3 Evaporator sensor malfunction Quick-flash E3
4 Condenser sensor malfunction Quick-flash E4
5 Water pump temperature sensor Quick-flash E5
6 Outdoor malfunction Quick-flash Quick-flash Quick-flash Quick-flash E6
7 EEPROM malfunction Quick-flash Quick-flash E7
8 Water-level alarm malfunction Quick-flash E8
9 DC motor speed out of control Quick-flash Quick-flash Eb
10 Outdoor unit low pressure malfunction Quick-flash Quick-flash Quick-flash Ed
11 Lifting panel communication checking
channel is abnormal Quick-flash Quick-flash Quick-flash F0
12 Lifting panel malfunction Quick-flash Quick-flash Quick-flash F1
13 Lifting panel is not closed On Quick-flash Quick-flash F2
14 Refrigerant leakage detection malfunction Quick-flash Quick-flash EC
Table 8-1

Symptoms Causes Solution
Unit does not start
• Power failure.
• Power switch is off.
• Fuse of power switch may have burned.
• Batteries of remote controller exhausted
or other problem of controller.
• W ait for the comeback of power.
• Switch on the power.
• Replace the fuse.
• Replace the batteries or check the
controller.
Air flowing normally but
completely can't cooling
• Temperature is not set correctly.
• Be in 3 minutes protection of compressor.
• Set the temperature properly.
• Wait.
Units start or stop
frequently
• Refrigerant is too little or too much.
• Airor no concreting gas in the refrigerating
circuit.
• Compressor is malfunction.
• Voltage is too high or too low.
• System circuit is blocked.
• Check leakage, and rightly recharge
refrigerant.
• Vacuum and recharge refrigerant.
• Maintenance or change compressor.
• Install manostat.
Low cooling effect
• Outdoor unit and indoor unit heat
exchanger is dirty.
• The air filter is dirty.
• Inlet/outlet of indoor/outdoor units is
blocked.
• Doors and windows are open
• Sunlight directly shine.
• Too much heat resource.
• Outdoor temp. is too high.
• Leakage of refrigerant or lack of
refrigerant.
• Find reasons and solution.
• Clean the heat exchanger.
• Clean the air filter.
• Eliminate all dirties and make air
smooth.
• Close doors and windows.
• Make curtains in order to shelter from
sunshine.
• Reduce heat source.
• AC cooling capacity reduces (normal).
Low heating effect
• Outdoor temperature is lower than 7°C .
• Doors and windows not completely
closed.
• Leakage of refrigerant or lack of
refrigerant.
• Check leakage and rightly recharge
refrigerant.
• Use heating device.
• Close doors and windows.
• Check leakage and rightly recharge
refrigerant.
Table 8-2
Symptoms Causes Solution
The fan speed can not be
changed.
• Check whether the MODE indicated on the
display is "AUTO"
When the automatic mode is selected, the
air conditioner will automatically change
the fan speed.
• Check whether the MODE indicated on the
display is "DRY"
When dry operation is selected, the air
conditioner automatically change the fan
speed. The fan speed can be selected
during "COOL" , "FAN ONLY", and
"HEAT".
The remote controller
signal is not transmitted
even when the ON/OFF
button is pushed.
• Check whether the batteries in the remote
controller are exhausted. The power supply is off.
The TEMP. indicator does
not come on.
• Check whether the MODE indicated on the
display is FAN ONLY
The temperature cannot be set during FAN
mode.
The indication on the
display disappears after
a lapse of time.
• Check whether the timer operation has
come to an end when the TIMER OFF is
indicated on the display.
The air conditioner operation will stop up
to the set time.
The TIMER ON indicator
goes off after a lapse of
certain time.
• Check whether the timer operation is
started when the TIMER ON is indicated on
the display.
Up to the set time, the air conditioner will
automatically start and the appropriate
indicator will go off.
No receiving tone sounds
from the indoor unit even
when the ON/OFF button
is pressed.
• Check whether the signal transmitter of the
remote controller is properly directed to the
infrared signal receiver of the indoor unit
when the ON/OFF button is pressed.
Directly transmit the signal transmitter of
the remote controller to the infrared signal
receiver of the indoor unit, and then
repeatly push the ON/OFF button twice.
Table 8-3

AIR CONDITIONER REMOTE
CONTROLLER
Thank you very much for purchasing our air
conditioner. Please read this owner's manual
carefully before using your air conditioner.
The design and specifications are subject to change
without prior notice for product improvement.
Consult with the sales agency or manufacturer for
details.
Handling the remote controller
Location of the remote
controller.
• Use the remote controller
within a distance of 8
meters from the appliance,
pointing it towards the
receiver. Reception is
confirmed by a beep.
CAUTION
• The air conditioner will not operate if curtains,
doors or other materials block the signals from the
remote controller to the indoor unit.
• Prevent any liquid from falling into the remote
controller. Do not expose the remote controller to
direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is
exposed to direct sunlight, the air conditioner may
not function properly. Use curtains to prevent the
sunlight from falling on the receiver.
• If other electrical appliances react to the remote
controller, either move
these appliances or consult your local dealer.
______________________________________
Replacing batteries The remote controller is
powered by two dry
batteries(R03/LR03X2)
housed in the rear part and
protected by a cover.
(1) Remove the cover by
pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries, placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the remote
controller erases all programming. After inserting
new batteries, the remote controller must be
reprogrammed.
CAUTION
• Do not mix old and new batteries or batteries of a
different type. Do not leave the batteries in the
remote controller if it is not going to be used for 2 or
3 months.
• Dispose of the old batteries in the special
containers to be found in the sales outlets.
Remote Controller Specifications
Model RG51C/(C)E, RG51C/BG(C)E.
Rated Voltage 3.0V(Dry batteries R03/LR03×2)
Lowest Voltage of
CPU Emitting
Signal
2.0V
Signal Receiving
Range 8m (when using 3.0 voltage, it gets 11m)
Environment -5O°C~60°C
Performance Feature
1. Operating Mode: AUTO, COOL, DRY, HEAT
(Cooling & heating models only) and FAN.
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature range: 17OC~30OC.
4. Full function of LCD (Liquid Crystal Display)
Note:
• Buttons design might be slightly different from the
actual one you purchased depending on individual
models.
• All the functions described are accomplished by
the indoor unit. If the indoor unit has no this feature,
there is no corresponding operation happened when
press the relative button on the remote controller.

Function buttons
TEMP UP Button
Push this button to increase the indoor temperature setting in 1°C
increments to 30°C.
TEMP DOWN Button
Push this button to decrease the indoor temperature setting in 1°C
increments to 17°C.
MODE Button
Each time the button is pressed, the operation mode is selected in
the sequence of the following:
NOTE: Heat mode is for Cooling & Heating models only.
SWING Button
Used to stop or start horizontal louver movement. The louver will
swing up and down automatically if push this button.
AIR DIRECTION Button
Used to set the desired up/down air flow direction. The louver
changes 6 degree in angle for each press.
SWING Button
Used to stop or start vertical louver movement .
NOTE: This button only available when the remote controller is
used with corresponding unit.
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
ON/OFF Button
Operation starts when this button is pressed and stops when the
button is pressed again.
FAN SPEED Button
Used to select the fan speed in four steps:
FAN SPEED Button+ MODE Button
Press the Mode and Fan speed button simultaneously for 2 seconds. The remote controls into faceplate setting
state and the LCD shows F2.Press the TEMP UP( ) to control the faceplate up and press the TEMP DOWN( )
to control the faceplate down. Press any button to exit the faceplate setting state, then the LCD back to the
normal display.
TIMER ON Button
Press this button to activate the Auto-on time setting. Each press will increase the time setting in 30 minutes
increments, up to 10 hours, then at 1 hour increments up to 24 hours. To cancel the Auto-on time setting, just
press the button until the time setting is 0.0.
ECO Button
Select this function during the sleeping time. It can maintain the most comfortable temperature and save energy.
This function is available on COOL, HEAT or AUTO mode only .
NOTE: While the unit is running under Energy-saving mode, it would be cancelled if press MODE, FAN SPEED or
ON/OFF button.
TIMER OFF Button
Press this button to activate the Auto-off time setting. Each press will increase the time setting in 30 minutes
increments, up to 10 hours, then at 1 hour increments up to 24 hours. To cancel the Auto-off time setting, just
press the button until the time setting is 0.0.
LOCK Button
Press this recessed button to lock all current settings, and the remote controller will not accept any operation
except that of the LOCK. Use the LOCK mode when you want to prevent settings from being changed
accidentally. Press the LOCK button again to cancel the LOCK function. A lock symbol will appear on the remote
controller display when the lock function is activated.

Indicators on LCD
MODE display
Displays the current selected mode. Including AUTO, COOL, DRY,
HEAT(cooling & heating models only) and FAN.
Transmission Indicator
This transmission indicator will light when remote controller transmits
signals to the indoor unit.
Temp./Timer display
The temperature setting (from 17OC to 30OC) or timer setting (0~24h) will
be displayed. If FAN mode is selected, there will be no display.
ON/OFF display
This indicator will be displayed when the unit is operating.
MODE display(FAN mode)
FAN SPEED display
Displays the selected fan speed: AUTO, HIGH, MED(if applicable) and
LOW. Nothing displays when the fan speed is selected in AUTO speed.
When AUTO or DRY Mode is selected, there will be no signals displayed.
TIMER display
This display area shows the settings of the TIMER. That is, if only the Auto-
on time function is set, it will display TIMER ON. If only the Auto-off time
function is set, it will display TIMER OFF. If both functions are set, it will
display TIMER ON OFF which indicates you have chosen both the Auto-on
time and Auto-off time.
LOCK Indicator
LOCK display is displayed when pushing the LOCK button. Push the LOCK
button to clear display.

How to use the buttons Auto operation
Ensure the unit is plugged in and power is available. The OPERATION indicator
on the display panel of the indoor unit illuminates.
1. Press the MODE button to select Auto.
2. Press the TEMP button to set the desired temperature. The temperature can
be set within a range of 17OC~ 30OC in 1OC increments.
3. Press the ON/OFF button to start the air conditioner.
NOTE
1. In the Auto mode, the air conditioner can logically choose the mode of Cooling, Fan,
Heating and Dehumidifying by sensing the difference between the actual ambient room
temperature and the set temperature on the remote controller.
2. In the Auto mode, you can not switch the fan speed. It has already been automatically
controlled.
3. If the Auto mode is not comfortable for you , the desired mode can be selected manually.
Cooling/ Heating/ Fan operation
Ensure the unit is plugged in and power is available.
1. Press the MODE button to select COOL, HEAT, (cooling & heating models
only) or FAN mode.
2. Press the TEMP button to set the desired temperature. The temperature can
be set within a range of 17OC~ 30OC in 1OC increments.
3. Press the FAN SPEED button to select the fan speed in four steps- Auto, Low,
Med, or High.
4. Press the ON/OFF button to start the air conditioner.
NOTE
In the FAN mode, the setting temperature is not displayed in the remote controller and you
are not able to control the room temperature either. In this case, only step 1, 3 and 4 may
be performed.
Dehumidifying operation
Ensure the unit is plugged in and power is available. The OPERATION indicator
on the display panel of the indoor unit illuminates.
1. Press the MODE button to select DRY mode.
2. Press the TEMP button to set the desired temperature. The temperature can
be set within a range of 17°C~ 30°C in 1°C increments.
3. Press the ON/OFF button to start the air conditioner.
NOTE
In the Dehumidifying mode, you can not switch the fan speed. It has already
been automatically controlled.
Dehumidifying volume is 5 L/h

Swing operation
Use the DIRECTION/SWING button to adjust the horizontal louver, use the SWING
button to adjust the vertical louver.
1. Press the SWING or ( ) button, the horizontal or vertical louver will swing
automatically. when press the AIR DIRECTION button, the louver changes 6
degree in angle for each press.
NOTE: When the louver swing or move to a position which would affect the cooling
and heating effect of the air conditioner, it would automatically change the swing/
moving direction.
Timer operation
Press the TIMER ON button can set the auto-on time of the unit. And press the
TIMER OFF button can set the auto-off time of the unit.
To set the Auto-on time.
1. Press the TIMER ON button. The remote controller shows TIMER ON, the last
Auto-on setting time and the signal "h" will be shown on the LCD display area.
Now it is ready to reset the Auto-on time to START the operation.
2. Push the TIMER ON button again to set desired Auto-on time. Each time you
press the button, the time increases in 30 minutes increments, up to 10 hours,
then at 1 hour increments up to 24 hours.
3. After setting the TIMER ON, there will be a one-half second delay before the
remote controller transmits the signal to the air conditioner. Then, after
approximately another 2 seconds, the signal "h" will disappear and the set
temperature will re-appear on the LCD display window.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote controller shows TIMER OFF, the last Auto-off setting time and the
signal "h" will be shown on the LCD display area. Now it is ready to reset the Auto-off time to START the
operation.
2. Push the TIMER OFF button again to set desired Auto-off time. Each time you press the button, the time
increases in 30 minutes increments, up to 10 hours, then at 1 hour increments up to 24 hours.
3. After setting the TIMER OFF , there will be a one-half second delay before the remote controller transmits the
signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" will disappear and the set
temperature will re-appear on the LCD display window.
IMPORTANT
The effective operation time set by the remote controller for the timer function is limited to the following settings:
0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15, 16, 17,
18, 19, 20, 21, 22, 23 and 24.

Example of Timer setting
TIMER ON (Auto-on Operation)
The TIMER ON feature is useful when you want the unit to turn on automatically before
you return home. The air conditioner will automatically start operating at the set time.
Example:
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting of starting operation time and the signal
"h" will show on the display area.
2. Press the TIMER ON button to display "6:0h" on the TIMER ON display of the remote
controller.
3. Wait for about 3 seconds and the digital display area will show the temperature
again. Now this function is activated.
TIMER OFF (Auto-off Operation)
The TIMER OFF feature is useful when you want the unit to turn off automatically after
you go to bed. The air conditioner will stop automatically at the set time.
Example:
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of stopping operation time and the
signal "h" will show on the display area.
2. Press the TIMER OFF button to display "10h" on the TIMER OFF display of the
remote controller.
3. Wait for about 3 seconds and the digital display area will show the temperature again.
Now this function is activated.
COMBINED TIMER (Setting both ON and OFF timers simultaneously) TIMER OFF →TIMER ON
(On →Stop →Start operation)
This feature is useful when you want to stop the air conditioner after you go to bed,
and start it again in the morning when you wake up or when you return home.
Example:
To stop the air conditioner 2 hours after setting and start it again 10 hours after
setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display 2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h on the TIMER ON display .
5. Wait for the remote control to display the setting temperature.
TIMER ON -TIMER OFF
(Off -* Start -* Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
Example:
To start the air conditioner 2 hours after setting, and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display 2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display 5.0h on the TIMER OFF display .
5. Wait for the remote control to display the setting temperature.
CAUTION
• The timer setting(TIMER ON or TIMER OFF) that in sequence occurs directly after
the set time will be activated first.
ECO operation
The ECO function enables the unit to automatically increase(cooling) or decrease (heating)
1OC per hour for the first two hours, then hold steady for the next 5 hours, after that the unit
will stop operation. It can maintain the most comfortable temperature and save energy.
NOTE: The ECO function is only available under Cooling, Heating and AUTO operation.

ELECTRIC SCHEMATIC DIAGRAM
ASC-60AN indoor unit
ASC-60AN outdoor unit

FOUR-WAY CASSETTE
TYPE AIR CONDITIONER
EXCESSIVE OPERATING
PRESSURE
28.3kg
WEIGHT(INDOOR)
220-240V~ 50Hz 1Ph
POWER SOURCE
1.0A
RATED CURRENT
150W
RATED INPUT
DISCHARGE
4.2MPa
1.5MPa
SUCTION
INDOOR MODEL
ASC-60AN
COOLING CAPACITY
14.9kW
HEATING CAPACITY
17.0kW
111.1kg
R410A/3500g
7000W
19.0A
1.5MPa
4.2MPa
SPLIT UNIVERSAL AIR
CONDITIONER OUTDOOR UNIT
OUTDOOR MODEL
380-415V 3N~ 50Hz
IP 24
REFRIGERANT
EXCESSIVE OPERATING
PRESSURE
WEIGHT(OUTDOOR)
POWER SOURCE
OUTDOOR UNIT
RESISTANCE CLASS
DISCHARGE
ASC-60AN
SUCTION
RATED INPUT
RATED CURRENT
RATING LABEL

Manufacturer
Outside
Unit
Inside Unit
Energy
A
B
C
D
E
F
G
More efficient
Less
efficient
Noise
(dB(A) re 1 pW)
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/EC
Annual energy consumption,
kWh in cooling mode
kW
(Actual consumption will depend
on how the appliance is used
and climate)
Full load (the higher the better)
Cooling output
Energy
efficiency
ratio
Type
Cooling only
Cooling + Heating
Air cooled
Water cooled
Heat output
Heating Performance
A: higher
G: lower
kW
Air-Conditioner
3015
14.95
2.48
E
55
17
ABCDEFG
ASC-60AN
ASC-60AN
Manufacturer
Outside
Unit
Inside Unit
Energy
A
B
C
D
E
F
G
More efficient
Less
efficient
Noise
(dB(A) re 1 pW)
Further information is contained
in product brochures
Norm EN 14511
Air-conditioner
Energy Label Directive 2002/31/EC
Annual energy consumption,
kWh in cooling mode
kW
(Actual consumption will depend
on how the appliance is used
and climate)
Full load (the higher the better)
Cooling output
Energy
efficiency
ratio
Type
Cooling only
Cooling + Heating
Air cooled
Water cooled
Heat output
Heating Performance
A: higher
G: lower
kW
Air-Conditioner
2685
15.24
2.84
C
55
16.74
ABCDEFG
ASF-60AN
ASF-60AN
ENERGY LABEL



NOTE CONCERNING PROTECTION OF ENVIRONMENT
This product must not be disposed of via normal household waste after its
service life, but must be taken to a collection station for the recycling of
electrical and electronic devices. The symbol on the product, the
operating instructions or the packaging indicate such disposal procedures.
The materials are recyclable in accordance with their respective symbols. By means
of re-use, material recycling or any other form of recycling old appliances you are
making an important contribution to the protection of our environment. Please ask
your local council where your nearest disposal station is located.
INFORMATION CONCERNING USED REFRIGERANT
MEDIUM
This unit is containing fluorinated gases included in the Kyoto protocol. The
maintanance and the liquidation must be carried out by qualified personel.
Type of refrigerant: R410A
The composition of the cooling medium R410A: (50% HFC-32, 50% HFC-125)
The quantity of the refrigerant: please see the unit label.
The value GWP: 2088
GWP = Global Warming Potential
In case of quality problem or other please contact your local supplier or authorized
service center.
Emergency number: 112
PRODUCER
Producer: SINCLAIR CORPORATION Ltd., 1-4 Argyll St., London W1F 7LD, UK,
www.sinclair-eu.com
This product was manufactured in China (Made in China).
REPRESENTATIVE, TECHNICAL SUPPORT
NEPA spol. s r.o.
Purkyňova 45
612 00 Brno
Czech Republic
Tel.: [phone]
Fax: [phone]
www.nepa.cz
[email protected]