Sinclair ASH-09AF Quick start guide

AIR CONDITIONING
Internet: http://www.sinclair-eu.com
E-mail: [e-mail]
WALLMOUNTED SPLIT AIR CONDITIONER SINCLAIR
OPERTIONAL MANUAL
ASH-09AF, ASH-12AF
FLAT SERIE
Before operation please carfully read this manual.

Ｃｏｎｔｅｎｔｓ
Structure and Function
1
Important Advice 2
Specificate Model and Technical Data ５
Name and Function of Every Button of Wireless Remote Control 6
Operation Guide 8
Install Note Items 9
Install of Indoor Unit 12
Install of Outdoor Unit 14
Trial Run 17
Repair and Maintenance 18
When the unit cannot run normally 19
KFR-20GW/NaA512
Structure Principle and Usage
Install Part
Repair
Maintenance
and

Structure Principle and Usage
Structure and Function
◆
Ｐａｎｅｌ Ｆｉｌｔｅｒ
Air out
ｃｏｖｅｒ ｐｌａｔｅ
Ｄｒａｉｎａｇｅ ｈｏｓｅ
Power plug
Wireless remote control
Ａｉｒ ｉｎ
Front grill of air outlet vent
： Heat
Air out
Outdoor
unit
Ｗｉｒｅ ｃｏｎｎｅｃｔｉｏｎ
ｕｎｉｔ
Ｉｎｄｏｏｒ
Ａｉｒ ｉｎ
:Cool/Dry
:Run
:Auto
Connection pipe and wire

Important Advance (Read the follwoing items carefully before using the unit)
Insert power plug firm enough
shock or fire.
For loose insert may cause electric
Don't plug out power plug
when unit is operating.
occur.
Or electric shock or fire may
Don't damage wire or use the
wire that is not appointed.
Or electric shock or fire may
occur.
Don't share socket with other
appliances or use prelonged hose.
occur.
Or electric shock or fire may
Don't operate unit with wet
hand for electric shock may occur.
vents, or damage may occur.
Don't let cooled air blows body
directly for too long, and don't
set indoor temp. too low for it is
If abnormal phenomenon occurs
(like burning odor etc.), cut off
power supply first, then contact
Gree Service Center. If abnormal
continues, the unit may be damaged
and cause electric shock or fire.
Don't repair the unit yourself
for incorrect repair may cause
electric shock or fire. So, contact
Gree Service Center to have
ＷＡＲＮＩＮＧ
Don't insert finger or stick-
like thing into air inlet and outlet
Danger
Structure Principle and Usage
not good for health.
Cut off power
unit repaired.

★Earthing: Earth must be
reliable! Earth wire should be
connected on special earth settings．
connected by perfessional personnel
Don't connect earth wire onto gas
pipe, water pipe, blowing pipe or
★Plug out power plug when the
unit will not be used for a long time.
★Cut off power when cleaning
the unit. Otherwise, electric shock
or damage may occur.
Otherwise, fire may be caused
★Don't plug out the plug by
pulling the power hose.
for over heat of wire.
★Don't let the unit blows to
monoxide poisoning may occur for
heater or cooker directly. Or carbon
incomplete burn.
★Chemical sprayer must be
placed 1m away from both indoor
and outdoor unit to prevent fire
without repair, unit may fall down
★Note if install chassis is
damaged. If the chassis is damaged
and cause injury.
things may fall down and cause
★Don't stand or put things on
the outdoor unit. For people or
injury.
★Don't block the air inlet or outlet
vent of both indoor and outdoor unit.
It would cause low performance
or stop of unit.
If there is no such settings, have it
place where perfessiona personnel
Structure Principle and Usage
considers it unrealiable.
or explosionor explosion

４
50Hz~230V
Proper set temp. can save electricity.
Indoor temperature should be set properly
When the unit is running, adjust up and down adjusting plate
●Adjust airflow and direction properly
by wireless remote control can adjust vertical direction of
air, hold the adjust plate that control left and rignt direction
can adjust horizontal flow direction of air.
●Don't blow pets or plants directly for it is not
good for them.
Left and right adjust plate
When the unit is running, don't open windows
or doors of the room for long time.
It would lower performance of the unit.
Temp. dif of
indoor and outdoors
Don't pour water on the unit or wash it by water
for malfunction or electric shock may occur.
Power hose of this unit adopts X type connection, don't
cut off or damage it and signal control wire. If power
hose or signal wire is damaged, please have them
changed by trained maintainer.
The unit allow voltage fluctuation of ２３０±１０％Ｖ，
too low of voltage may increase libration of
compressor that cause damage on cool system.
This unit cannot be used to dry clothes or refrigerate
and store foods etc..
Up and down adjust plate
Structure Principle and Usage
ＮＯＴＩＣＥ
should be５℃

Specificate Model and Technical Data
All above are tested according to standard ＧＢ／Ｔ７７２５－１９９６, cooling capacity, heating capacity and noise etc. are tested before leaving factory
If the data are changed, please refer the one offered on nameplate.
Model ASH-07AF ASH-09AF ASH-12AF
Function Cooling and Heating Cooling and Heating Cooling and Heating
Cooling Capacity（W）2000 2500 3500 Heating Capacity（W）2300 2700 3700
Rated Voltage 230V～ Rated Frequency 50Hz
Cooling/Heating Rated Power (W)
920/920 920/920 1440/1440
Cooling/Heating Rated Currency (A)
4/44/46.26/6.26
Air Flow（m３/h）450 450 500
Name of Refrigerant and Charge Amount
R410A1. 2kg R410A1.35kg R410A1.4kg
Noise (Indoor/Outdoor) dB（A）
38/52 38/53 40/54
Climate Type T1
Water-proof Level IP×4
Electric Shork Proof Protect Type
I
Weight (Indoor/Outdoor) (kg)
11/32 11/32 11/36
Outline Diameter (Indoor/Outdoor)
（W×H×D）（cm）
Indoor：101.5×29.0×15 Outdoor：84.8×54.0×32.0
Structure Principle and Usage

Remote control operation procedure
Name and Function-Remote control
Note:
Be sure that there are no obstructions between receiver and remote controller.
The remote control signal can be received at the distance of up to about 10m.
Don’t drop or throw the remote control.
Don’t let any liquid in the remote controller and put the remote controller di-
rectly under the sunlight or any place where is very hot.
SWING button
When it is pressed, the louvers
start to rotate automatically and
stop when repressed.
TEMP.button
SET TEMP. increases 1 by
pressing button once,and decreases
1by pressing button once.
At COOL mode operation, SET
TEMP. can be selected from 16 to
30 .
At DRY mode operation, SET TEMP.
can be selected from 16 to 30 .
At HEAT mode operation, SET
TEMP. can be selected from 16 to
30 .
MODE button
press this button to change the
operation mode in order of:
FAN button
Press this button to change
the fan speed of:
“ ” COOL mode
“ ” DRY mode
“ ” FAN mode
“ ” HEAT mode
ON/OFF button (1/0is
used in some models)
Press this button to turn on
or turn off the unit.
AUTO
3
REMOTE CONTROL OPERATION PROCEDURE

Name and Function-Remote control. (Remove the cover)
Note: This type of remote controller is a kind of new controller.
some buttons of the controller which are not available to thisAir condi-
tioner will not be described below.
Operate on unmentioned buttons would not impact on the normal use.
SLEEP button
Press this button to set
SLEEP operation.And stop
when repressed.
TIMER OFF button
At operating, press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to
stop the unit automatically.
TIMER ON button
At stopping, press TIMER
ON button, set ON TIME in
range of 0 to 24 hour at the
interval of 0.5h to start the
unit automatically.
0 24h
Timer
cancellation
0 24h
Timer
cancellation
Liquid crystal displayer It
shows all set contents.
1/0 is used in some
models
4
REMOTE CONTROL OPERATION PROCEDURE

COOL mode operation procedure
According to difference between room temp. and set temp., microcomputer can control cooling on or
not.
If room temp. is higher than set temp., compressor runs at COOL mode.
If room temp. is lower than set temp., compressor stops and only indoor fan motor runs.
SET TEMP. should be in range of 16 to 30
4.Press FAN button, set
fan speed.
5.Press TEMP. but-
ton, set suitable SET
TEMP.
2.Press MODE button,
set operation
mode.
3.Press SWING button,
the louvers start to ro-
tate automatically, and
stop when repressed.
1.Plug in, press ON/OFF button
(1/0is used in some models),then
air conditioner is turned on.
5
REMOTE CONTROL OPERATION PROCEDURE

HEAT mode operation procedure
If room temp. is lower than set temp., compressor runs at HEAT mode;
If room temp. is higher than set temp., compressor and outdoor fan motor stop, only indoor fan motor
runs, louver motor makes the louvers horizontal.
SET TEMP. should be in range of 16 to 30
4.Press FAN button, set
fan speed.
5.Press TEMP. but-
ton, set suitable
SET TEMP.
1.Plug in, press ON/OFF button
(1/0is used in some models),
then air conditioner is turned on.
2.Press MODE button,
set operation
mode.
3.Press SWINGbutton, the
louvers start to rotate
automatically, and stop
when repress it.
6
REMOTE CONTROL OPERATION PROCEDURE

DRY mode operation procedure
If room temp. is lower than set temp., compressor ,outdoor and indoor fan motor stop. If room temp. is
between 2of set temp., Air conditioner is drying.If room temp. is higher than set temp., it’s at
COOL mode.
SET TEMP. should be in range of 16 to 30
3.Press SWING button,
the louvers start to ro-
tate automatically, and
stop when repress it.
4.Press TEMP.button,set
suitable SET TEMP.
2.Press MODE button,set
operation mode.
Air speed couldn’t be
changed after the “ ”
being set.
1.Plug in,press ON/OFF button
(1/0is used in some models),then
air conditioner is turned on.
7
REMOTE CONTROL OPERATION PROCEDURE

AUTO mode operation procedure
Under Auto mode operation, standard SET TEMP. is 25 for COOL mode and 20 for HEAT
mode.
2.According to room temp.,micro-
computer can automatically set
operation mode,so
as for best effect.
1.Plug in,Press ON/OFF but-
ton (1/0is used in some
models), then air conditioner
is turned on.
8
REMOTE CONTROL OPERATION PROCEDURE

TIMER mode operation procedure
TIMER OFF button
At operating, press TIMER
OFF button, set OFF TIME
in range of 0 to 24 hour to
stop the unit automatically.
0 24h
Timer
cancellation
TIMER ON button
At stopping, press TIMER
ON button, set ON TIME in
range of 0 to 24 hour to start
the unit automatically.
0 24h
Timer
cancellation
1/0 is used in some models
9
REMOTE CONTROL OPERATION PROCEDURE

SLEEP mode operation procedure
4.Press FAN button, set
fan speed.
5.Press TEMP. but-
ton, set suitable
SET TEMP.
1.Plug in, press ON/OFF button
(1/0is used in some models),then
air conditioner is turned on.
2.Press MODE button,
set or op-
eration mode.
3.Press SWINGbutton, the
louvers start to rotate
automatically, and stop
when repress.
6.SLEEP button
Press it to set SLEEP
operation.
As the unit is cooling or drying, if SLEEP operation is set, SET TEMP. would increase 1 in 1 hour
and 2 in 2 hours.
As the unit is heating , if SLEEP operation is set, SET TEMP. would decrease 1 in 1 hour and 2 in
2 hours.
10
REMOTE CONTROL OPERATION PROCEDURE

How to insert batteries
1.Remove the cover from the back
of the remote control.
2.Insert the two batteries (TwoAAA
dry - cell batteries ) and press but-
ton “ACL”.
3.Re - attach the cover.
NOTE:
Don’t confuse the new
and worn or different
types of batteries.
Remove batteries when
the remote controller is
not in use for a long
time.
The remote control sig-
nal can be received at
the distance of up to
about 10m.
The lifetime of the bat-
teries is about one year.
The remote controller
should be placed about
1m or more away from
the TV. or any other
electric appliances.
Bad batteries are for-
bidden.
1.Remove the cover.
3.Re - attach the cover.
2. Insert the AAA batteries.
11
REMOTE CONTROL OPERATION PROCEDURE

９
Install Part
１．The air inlet and outlet vent should be far away from obstruction to ensure the air
Indoor unit
is blowed to the entire room.
2.Select where is easy to drain condensate or connect with outdoor unit.
3.Far away from heat resource, steam and flammable gas.
4.Select where can stand weight of indoor unit without increasing running noise and librations.
5.Ensure there is enough space for maintenance, and indoor unit should be at lest 2m above floor.
6.Place the unit to where is at lest 1m away from TV, Hi-fi and other appliances.
7.Select where air filter can be taken out easily.
Outdoor unit
１．Select place where noise and airflow produced when exharsting will not annoy neighbours.
２．Ensure well ventilation of outdoor unit.
３．There is no obstruction that may impact air in and out nears outdoor unit.
４．Install place should be able to stand weight and libration of outdoor unit and let the
outdoor unit run safely.
５．Select place where there is no leakage of flammable or corrosible gas.
◆ Install Note Items
Select of install location
８．Ensure the install of indoor unit meets requirements on Install Dimension Diagram.
６．Ensure the install of outdoor unit meets requirements on Install Dimension Diagram.

１０
Ｗｉｒｅ ｃｏｌｌｏｃａｔｉｏｎ
１．Wire should be connected according to local wiring regulation.
２．Power supply must adopt rated voltage and special circuit for air conditioner,
and size of the power wire should be big enough.
４．Earthing should be reliable, and should be connected on special earthing settings on building,
and have them connected by professional personnel. Creepage protect switch and air switch
with enough capacitance must be set in rated circuitry (Refer to the following form). Air switch
Ｃａｐａｃｉｔａｎｃｅ
ｏｆ ａｉｒ ｓｗｉｔｃｈ
Ｅａｒｔｈ ｗｉｒｅ
ｍｉｎ ｓｅｃｔｉｏｎ
Ｐｏｗｅｒ ｗｉｒｅ ｏｆ ｕｎｉｔ
ｍｉｎ． ｓｅｃｔｉｏｎ
ASH-07AF
ASH-12AF
１０Ａ
Ｅａｒｔｈｉｎｇ ｒｅｑｕｉｒｅｍｅｎｔｓ
１．Air conditioner is type I appliance, please do conduct reliable earthing measure.
２．The yellow-green wire in the unit is earth wire, don't use it for other purpose or cut it.
Don't fix it by self tapping screw, or electric shock may occur.
①Ｗａｔｅｒ ｐｉｐｅ ② Ｇａｓ ｐｉｐｅ ③Ｂｌｏｗｉｎｇ ｐｉｐｅ④Ｗｈｅｒｅ ｐｒｏｆｅｓｓｉｏｎａｌ ｐｅｒｓｏｎｎｅｌ ｃｏｎｓｉｄｅｒｓ ｉｔ ｕｎｒｅｌｉａｂｌｅ
Ｍｏｄｅｌ
ASH-09AF
１．５ｍｍ２
１．０ｍｍ２
１．０ｍｍ２
１５Ａ
１０Ａ
１．５ｍｍ２
１．０ｍｍ２
１．０ｍｍ２
Ｉｎｓｔａｌｌ Ｐａｒｔ
３．Please don't pull power wire forcibly.
should maintain magnetic and heat drop-out functions to ensure protect when curcuit short or overload occurs.
following place:
３．User power supply should offer reliable earth terminal. Don't connect earth wire to

１１
Ｉｎｓｔａｌｌ Ｄｉｍｅｎｓｉｏｎ Ｄｉａｇｒａｍ
Ｉｍｐｏｒｔａｎｔ Ａｄｖａｎｃｅ
★ The installation must be done by professional personnel with reliability
according to this manual.
★ Contact service center before installation to avoid the malfunction due
to unprofessional installation.
Ｉｎｓｔａｌｌ Ｐａｒｔ
★ When moving the units, you must be guided by professional personnel.
Distance between
unit and ceiling
Distance between unit and wall
Distance between unit and floor
Air out side
Distance between unit and wall
Distance between
unit and slider
Air in side
Distance between unit and wall
Distance between unit and wall
Air out side

◆ Ｉｎｓｔａｌｌ ｔｈｅ ｉｎｄｏｏｒ ｕｎｉｔ
1.Always mount the rear panel horizon-
tally.As the water drainage pipe at
the left,this side should not be too
2.Fix the rear panel on the selected location.
3.Be sure that the rear panel has been fixed firmly enough to withstand
the weight of an adult of 60kg,furthermore,the weight should be
☆ Ｉｎｓｔａｌｌ ｔｈｅ ｒｅａｒ ｐａｎｅｌ
☆ Install the piping hole
１． Make the piping hole(¦Õ50) in the wall at a slight downward slant t o
２． Insert the piping-hole sleeve into the hole to prevent the connection
☆ Install the drain hose
1.For well draining, the drain hose shoule be placed
2.Do not wrench or bend the drain hose or flood its
end by water.
3.When the long drainage hose passing through indoor
Ｄｏｎ＇ｔ ｓｏａｋ ｉｎ ｔｈｅ ｗａｔｅｒ
Ｆｉｇ．２
☆ Install the connection pipes
tighten the flare nut of the connection pipes (Shown in P19"Install the connection
pipes")
Ｎｏｔｅ：
▲ Connect the connection pipes with the indoor unit
▲ Be careful in bending the connection pipes or you
▲ If the tightening torque is too great in tightening
☆ Electric wiring
1.Open the panel upwards.
2.Disassembly the fixing bolts of connection cover , shown in the Fig. at right side.
3.power connecting wire cross through down to up from the bottom of case.
１２
Ｆｉｇ．１
Ｂｅｎｔ
Ｗｒｅｎｃｈｅｄ
Ｉｎｓｔａｌｌ Ｐａｒｔ
ｃｏｖｅｒ ｏｆ ｃｏｎｎｅｃｔｉｏｎ
ｃｏｎｎｅｃｔｉｏｎ ｐｏｗｅｒ ｉｎｓｉｄｅ ａｎｄ
high when adjusting the rear panel.it
had better to adjust this side a little lower.
evenly shared each screw.
the outdoor side.
piping andwiring from being damaged when passing through the hole.
at a downward slant.
should wrap the insulation materials.
Connect the connection pipes with the relevant union pipes of the indoor unit and
ｏｕｔｓｉｄｅ ｔｈｅ ｕｎｉｔ
firstly and the outdoor unit secondly.
will damage the pipe.
the flare nuts, leakage will happen.