Sinclair ASDU-09A User manual

USER'S MANUAL
ASDU-09A, ASDU-12A, ASDU-18A, ASDU-24A
UNI ON/OFF SERIES
ASDU-36A, ASDU-42A, ASDU-48A, ASDU-60A
ducted units

Thanks for your selection of Sinclair Ducted Air-Conditioning Unit. Before use, please read this
instruction manual carefully and keep it properly to ensure correct use of this machine.

Safety Considerations 3
4
Temperature Setting
5
Fan Control
5
Component
Description
Sleep Function Setting
5
Operating Mode Setting
6
Timing Setting
6
7
Energy Saving Setting 7
Display of Outdoor Ambient Temperature 8
Power-fail Memory Function Setting 8
Debug Function 8
Operating
Instructions
for Line
Controller
Failure Display 9
Operation of Remote Controller 10
Unit Function 14
15
Operating
Instructions
Dual Sensor Setting
16
Installation Dimension of Indoor Unit
20
Installation of Outdoor Unit
22
Precautions on Installation of Indoor Unit and Outdoor Unit
24
Indoor Unit Level Inspection and Air Duct Installation
24
Installation and Test of Condensing Water Pipe and Selection of Connecting
Pipe
26
Installation of Connecting Pipe
27
Position and Method of Installing Wire Controller
29
Connection of Cables
31
Troubleshooting and Maintenance of Air Conditioner
35
Appendix
37
38
Installation
Instructions
for Air Duct
Weekly Timer
Wire controller (with week timer functions)
Turning On/Off Unit
Wire controller (standard fitting)

3
Safety Considerations
Please read this manual carefully before use and operate correctly as instructed in the manual.
1．You are specially warned to note the two symbols below.:
WARNING!：A symbol indicating that improper operation might cause human death or severe
injury
WARNING!：
A symbol indicating that improper operation might cause human property damage.
 This unit shall be used in offices, restaurants, residences or similar places.
WARNING!
 Please seek an authorized repair station for installation work. Improper installation might cause water leakage,
electric shock or fire.
 Please install at a place strong enough to support the weight of air conditioner unit. If not, the air conditioner
unit might fall down and cause human injury or death.
 To ensure proper drainage, the drainage pipe shall be correctly installed according to installation instructions.
Take proper measures for heat preservation to prevent condensing. Improper installation of pipes might cause
leakage and wet the articles in the room.
 Do not use or store flammable, explosive, poisonous or other dangerous substances beside the air conditioner.
 In case of trouble (e.g. burnt smell), please immediately cut off the main power of air conditioner unit.
 Keep air flow to avoid shortage of oxygen in the room.
 Never insert your finger or any objects into air outlet and inlet grill.
 Never plug or unplug the power cable directly to start or stop the air-conditioning unit.
 Please take constant care to check if the mounting rack is damaged after long use.
 Never modify the air conditioner. Please contact the dealer or professional installation workers for repair or
relocation of the air conditioner.
 The appliance shall not be installed in the laundry.
 Before installation, please check the power supply for compliance with the ratings on nameplate. Check the
power safety as well.(Operating by professinal)
 Before use, please check and confirm if the cables, drainage pipes and pipelines are correctly connected,
hence to eliminate the risk of water leakage, refrigerant leakage, electric shock or fire.
 Main power must be securely earthed to ensure effective grounding of air conditioner unit and avoid the risk
of electric shock. Please do not connect the earthing cable to coal gas pipe, water pipe, lightning rod or
telephone line.
 Once started, the air conditioner shall not be stopped at least after 5 minutes or longer; otherwise the oil
return to compressor may be affected.
 Do not let the child to operate the air conditioner unit.
 Do not operate the air conditioner unit with wet hands.
 Please disconnect the main power before cleaning the air conditioner or replacing the air filter.
 Please disconnect the main power if to put the air conditioner unit out of use for a long period.
 Please do not expose the air conditioner unit directly under corrosive environment with water or moisture.
 Please do not foot on or place any goods on air conditioner unit.
 After electrical installation, the air conditioner unit shall be energized for electrical leakage test.(Operating by professinal)
 If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard .
 An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected
in fixed wiring.
 The appliance shall be installed in accordance with national wiring regulations.
 The temperature of refrigerant circuit will be high, please keep the interconnection cable away from the
copper tube.

Wire controller (standard fitting)
• Never install the wire controller in a place where is water leakage.
• Avoid bunping, throwing, tossing or frequently opening the wire controller.
1Timing display
2Fan speed display (Auto, High speed, Medium
speed, Low speed)
3Defros ting st atus display
4Energy savingst atus display
5Set temperature display
6Ambient temperatur e display
7Fresh air st atus display (not supplied)
8Mode (cooling, dehumidifying,fan, heating, auto)
9Failure status display
10 Sleep st atus display
11 Mode key
12 Set temperature increase key
13 Set temperature decr ease key
14 Fan speed key (fresh air setting)
15 Sleep key (outdoor environment temperature check)
16 Timing key
17 ON/OFF key
Composition of wire controller
4

Turning ON/OFF unit
Pr ess t he ON/OFF ke y, then the unit shall st ar t up. Press t he ON/OFF
key again, then the unit shall shut off.
Fan contr ol (the figur es show the r elevant display ar eas)
If the fan control key is prssed consecutively, the fan speed shall changes
as per t he following sequence:
Low speed Medium speed Hight speed Auto
In the dehumidifying mode: The fan speed shall be automaticallyset as
low.
５
Oper ating istructions of wire controller
Temperatur e setting
Pr ess the temperature seting key ( ) to increase the set temperature;
press the temperature setting key ( ) to decrease the set temperature
(when pressing the keys once, the temperature shall increase or decrea-
se by 1 °C). NOTE: key lock function: when the ( ) and ( ) key arepressed
simultaneously for 5 second, the set temperature indicating area shall
display “EE” and all keys response shall be shut off; press the two keys
simultaneously for 5 second again, the key lock function shall be relea-
sed. When the wire controller is locked by remote monitor or centralized
controller, the keys of the wire controller and the signal of the remote
controller ar e all locked and invalidated, and then the set temperature
indicating ar ea shall display “CC”. Range of temperature setting under
various modes:
Heating: 16 °C~30 °C • Cooling: 16 °C~30 °C
Dehumidifying: 16 °C~30 °C •
Fan: No temperature se tting function

Sleep function setting
When the controller functions under cooling or dehumidifying mode and
if the unit runs for one hour after the sleep key is pressed, the set tem-
perature shall increase by 1, and the set temperature shall increase by
another 1 after 2 hours and the unit shall run as per the increased set
temperature. When the controller functions under heating mode and if
the unit runs for one hour after the sleep key is pressed, the set tempe-
rature shall decrease by 1, and the set temperature shall decrease by
another 1 after 2 hours and the unit shall run as per the decreased set
temperature. Fan mode does not have sleep function.
Operating Mode Setting
this key is pressed consecutively, the operating mode shall change as
per the following sequence:
Cooling Dehumidifying Fan Heating Auto
When the unit operates under “Cooling” mode, “COOL” shall be displayed.
Now the set temperature must be lower than the ambient temperature.
Now if the set temperature is higher than the ambient temperature, the
unit shall not produce cooling effect but shall only operate under Fan
mode.
When the unit operates under “Dehumidifying” mode, “DRY” shall be
displayed. Now the interior fan shall operate in the manner of low speed
air supply within a certain range of temperatures. The dehumidifying
effect of this mode is better than that of the Cooling mode and saves
more energy.
When the unit operates under “Heating” mode, “HEAT” shall be displayed.
Now the set temperature must be higher than the ambient temperature;
Now if the set temperature is lower than the ambient temperature, the
heating function shall not be started.
When the unit operates under “Fan” mode, “FAN” shall be displayed.
When the unit operates under “Auto” mode, “AUTO” shall be displayed
and the unit shall adjust its operating mode automatically according to
the ambient temperature.
When the unit operates under Heating mode and the outdoor tempera-
ture is low and the humidity is high, frost shall produce at the outdoor
unit. Now the heating efficiency shall be decreased. When frosting hap-
pens, the controller shall automatically start to defrost, and “DEFROST”
shall be displayed.
Note: Cooling only type unit does not have heating mode and when ener-
gy saving is set the Auto mode shall be invalidated.
6

%NERGY3AVING3ETTING
7HENTHEUNITISSHUTOFFPRESSTHEh&!.vKEYANDTHESIMULTANEOUSLYFOR
CONSECUTIVESECONDSTOACTIVATETHEENERGYSAVINGSETTINGMENU.OWh3!6%v
ANDh#//,vAREDISPLAYED)NCASEITISTHEFIRSTTIMETOSETENERGYSAVINGTHEINI
TIALVAL ESHALLBEDISPLAYED4HELOWERLIMITOFTEMPERATURESHALLBEDISPLAYED
ONTHESETTEMPERATUREANDTHETEMPERATUREVALUEUNDERSETTINGSHALLFLASH3ET
THELOWERLIMITOFCOOLINGTEMPERATUREUSINGTHEKEYORTHEKEYTHELOWER
LIMIT TEMPERATURE CAN BE SELECTED FROM THE RANGE BETWEEN  0RESS THE
h/./&&vKEYTOCONFIRMTHESETTING!LSOUSETHEKEYORTHEKEYTOSETTHE
UPPERLIMITOFTEMPERATUREANDTHETEMPERATUREVALUESHALLFLASHONTHEAMBIENT
TEMPERATUREAREA/54%.6AREATHEUPPERLIMITTEMPERATURECANBESELECTED
FROMTHERANGEBETWEEN0RESSTHEh/./&&vKEYTOCONFIRMTHESETTING
0LEASEPAY ATTENTIONTHATTHEUPPERLIMIT TEMPERATURE MUSTBE HIGHERTHAN THE
SETLOWERLIMITTEMPERATURE/THERWISETHESYSTEMSHALLREGARDTHEHIGHERTEM
PERATURE AS THE UPPER LIMIT TEMPERATURE AND THE LOWER ONE AS THE LOWER LIMIT
TEMPERATURE 0RESS THE h-/$%v KEY TO COMPLETE THE ENERGY SAVING SETTING FOR
THEMODESOFCOOLINGANDDEHUMIDIFYINGANDTURNTOTHEENERGYSAVINGSETTINGFOR
THE HEATING MODE #OOLING ONLY UNIT DOES NOT HAVE THIS FUNCTION .OW THE ,#$
DISPLAYSh3!6%vANDh(%!4v!FTERSETTINGISCOMPLETEDPRESSTHEh&!.vKEY
ANDTHEKEYSIMULTANEOUSLYFORCONSECUTIVESECONDSTOEXITTHESETTINGOF
ENERGYSAVING!FTERTHEENERGYSAVINGSETTINGINTERFACEISACTIVATEDTHESYSTEM
SHALLEXITTHEINTERFACEIFTHEREISNOANYOPERATIONWITHIN20 seconds afTERTHE
LASTKEYINPUTANDTHENORMALSHUTOFFSTATUSINTERFACESHALLBEDISPLAYED!FTER
THEABOVESETTINGSARECOMPLETEDTHESYSTEMSHALLDISPLAYh3!6%v.OWTHESET
TEMPERATURESHALLNOTEXCEEDTHETEMPERATURERANGEOFTHEENERGYSAVINGSET
TINGBEFORE &OR EXAMPLE THELOWERCOOLING LIMIT IS SET AS  ²#AND THEUPPER
COOLINGLIMITISSETAS²#FORTHEENERGYSAVINGTEMPERATURESETTINGIN
SOTHECOOLINGTEMPERATURECANONLYBESELECTEDFROMTHERANGEOF²#TO²#
BYUSINGTHEREMOTECONTROLLERORTHEWIRECONTROLLERLATER)FTHEUPPERLIMITTEM
PERATUREISTHESAMEASTHELOWERLIMITTEMPERATURETHESYSTEMCANONLYOPERA
TEATSUCHTEMPERATUREUNDERRELEVANTMODES2EMOVEOFENERGYSAVINGSETTING
4OREMOVETHEENERGYSAVINGSETTINGAFTERITTAKESINTOEFFECTYOUCANPRESSTHE
h&!.vANDTHEKEYSIMULTANEOUSLYFORCONSECUTIVESECONDSWHENTHEUNITIS
SHUTOFF"UTTHEVALUESETBEFOREWILLNOTBECLEAREDBUTASTHEINITIALSETTEMPE
RATUREFORTHENEXTENERGYSAVINGSETTING!FTERTHEUNITISDISCONNECTEDTOPOWER
SUPPLYTHEENERGYSAVINGSETTINGSHALLBESTORED4HESETTINGSTILLFUNCTIONSWHEN
THEUNITISCONNECTEDTOPOWERSUPPLYAGAIN)FTHEENERGYSAVINGMODEISSETTHE
SLEEPMODEANDTHEAUTOMODESHALLBEINVALIDATED

SWING
SWING
TIMER
TIMER
Timer Setting
When the unit is shut off, timing start can be set; After the unit is
started up, timing shutoff can be set. After the "TIMER"key is pressed,
the unit enters the timing set status and the word "TIMER" flashes on
the display. Now user can press ( ) or ( ) key to increase or decrease
the set time. Press the "TIMER" key again and then the timing shall
go into effect. Now the unit starts to count the time passed. When the
unit is under timing status, you can cannel timing set by pressing the
“TIMER” key.The range of set time is between 0.5 to 24 hours.
７
left.
U

8
$ISPLAYOF/UTDOOR!MBIENT4EMPERATURE
5NDERNORMALCONDITIONSTHEh/54%.6vCOLUMNSHALLONLYDISPLAYTHE
INDOORTEMPERATURE0RESSTHEh3,%%0vKEYFORCONSECUTIVESECONDS
WHENTHEUNITISSHUTOFFORSTARTUPTHE,#$SHALLDISPLAYh/54%.6v
!FTERTHEOUTDOORTEMPERATUREISDISPLAYEDFORSECONDSTHESYSTEM
SHALLRETURNTOTHEDISPLAYINTERFACEOFINDOORTEMPERATURE.OTE)FNOT
EQUIPPEDWITHANOUTDOORAMBIENTSENSORTHEUNITSHALLNOTHAVETHIS
FUNCTION
0OWERFAIL-EMORY&UNCTION3ETTING
0RESSANDHOLDTHEh-/$%vKEYFORSECONDSWHENTHEUNITISSHUTOFF
TOSWITCHSETVALUESSOASTODECIDEIFTHEUNITOPERATINGSTATUSORSHUTOFF
STATUSSHALLBEMEMORIZEDAFTERAPOWERFAIL)FTHESETTEMPERATUREAREA
DISPLAYSITMEANSTHEUNITOPERATINGSTATUSORSHUTOFFSTATUSSHALLBE
MEMORIZEDAFTERAPOWERFAILMEANSTHEOPERATINGSTATUSORSHUTOFF
STATUSSHALLNOTBEMEMORIZED0RESSTHEh/./&&vKEYTOSTORETHESET
VALUEANDEXITTHESETTING
$EBUG&UNCTION
7HENTHEUNITISSHUTOFFPRESSTHEh&!.vKEYANDTHEh3,%%0vKEYSIMUL
TANEOUSLY TO ACTIVATE THE DEBUG MENU .OW THE ,#$ DISPLAYS h$%"5'v
0RESSTHEh-/$%vKEYTOSELECTSETTINGITEMANDUSETHEKEY  O R  T H E 
KEYTOSETACTUALVALVE
3ETTINGOF!MBIENT4EMP3ENSOR
5NDERTHEDEBUGMODEPRESSTHE h-/$%vKEYSOASTODISPLAYhvON
THESETTEMPERATUREAREAATTHELEFTOFh$%"5'v4HE/54%.6AREAAT
THERIGHTOFh$%"5'vDISPLAYSSETTINGSTATUS.OWUSETHEKEYORTHE
KEYTOSELECTFROMTHEFOLLOWINGTWOSETTINGS
4HEINDOORROOMTEMPERATUREISMEASUREDATTHEAIRINTAKE.OWTHE
/54%.6AREADISPLAYS
4HEINDOORROOMTEMPERATUREISMEASUREDATTHEWIRECONTROLLER.OW
THE/54%.6AREADISPLAYS

The indoor room temperature is measured at the wire controller
when the mode is 'heating' or 'auto'. At other modes is measure at
the air intake(Now the OUT ENV area displaus 03) ,The default is 03.

Failure Display
When there is failure in the unit operation, “ERROR” will
flash on the LCD of the wire controller and the code of fai-
lure will also be displayed. When there are multiple failures
at the same time, the codes of failures will be displayed
one after one on the wire controller. The first digit of the
code denotes the system number. When there is only one
system, the system number is not displayed. The last two
digits denote the detailed failure code. For example, the
code in left means low pressure protection of com-
pressor.
The Codes of Failure Definitions are as Follows:
Fault code Fault Fault code Fault
E0 Pump Failure F0 Failure of Indoor Room Sensor at Air Intake
E1 Compressor High Pressure
Protection F1 Failure of Evaporator Temp. Sensor
E2 Indoor Frost-Proof Protection F2 Failure of Condenser Temp. Sensor
E3 Compressor Low Pressure
Protection F3 Failure of Outdoor Ambient Sensor
E4 Compressor Exhaust High
Temperature Protection F4 Failure of Exhaust Temp. Sensor
E5 Compressor Overheat
F5 Failure of Indoor Room Sensor at Wire
Controller
E6 Communications Failure
E8 Indoor Fan Protection EE Keys are locked (not failure)
E9 Full Water Protection CC
The unit is remotely monitored or controlled
by centralized controller and the wire control-
ler’s functions are invalidated (not failure)
FF Connected control communications
Failure
E5 Material Malfunction Will Be Showed By The Indicator Light On The Mother Board Of Outside Unit
SWING
TIMER
９

1０
Operation of Remote Controller
SWING FAN
• Ensure there is no obstacle between the remote controller and the signal recei-
ving window of the air conditioner.
• The distance able to receive the signal of the remote controller can be as far
as 8 meters.
• Never drop or throw at will the remote controller.
• Never let any liquid enter the remote controller. Avoid direct sunshine over the
remote controller. Do not place the remote controller in an extremely hot place.
Precautions:
Press FAN button, set fan speed
Press TEMP, button
set suitable TEMP
Press MODE but-
ton to set operation
mode
Plug in, press ON/OFF
button then air condi-
tioner is turned ON

Cooling Mode Operation
Connect the unit to power supply. Press the “ON/OFF”key.
Press the “MODE” key to select “Cooling” mode. Use the
“Temperature” key to adjust the set temperature for the
room.
a) After the unit is connected to
power supply, the air conditioning unit
shall enter the operating status if you
press the ON/OFF key
b) Press the mode key and select the
( ) mode
c) Press the temperature key and set
the temperature as required
Heating Mode Operation
Connect the unit to power supply. Press the “ON/OFF”key.
Press the “MODE” key to select “Heating” mode. Use the
“Temperature” key to adjust the set temperature for the
room.. Under the heating mode, the unit has the functions
of preventing cold air supply and supplying remaining heat.
After the startup of the compressor, the indoor fan shall
start operation when the evaporator temperature is larger
or equals 35 or after the unit has be started for 45 secon-
ds, so as to avoid supply of cold air shortly after the unit is
started. After the stop of the compressor, the indoor fan
shall stop operation after supplying air for 120 seconds.
a) After the unit is connected to
power supply, the air conditioning unit
shall enter the operating status if you
press the ON/OFF key
b) Press the mode key and select the
( ) mode
c) Press the temperature key and set
the temperature as required
1１

DRY (Dehumidifying) Mode Operations
Connect the unit to power supply. Press the “ON/OFF”
key. Press the “MODE” key to select “DRY (Dehumidifying)”
mode. Use the “Temperature” key to adjust the set tempe-
rature for the room.
a) After the unit is connected to
power supply, the air conditioning unit
shall enter the operating status if you
press the ON/OFF key
b) Press the mode key and select the
( ) mode
c) Press the temperature key and set
the temperature as required
Fan Mode Operation
Connect the unit to power supply. Press the “ON/OFF”key.
Press the “MODE” key to select “FAN” mode. The unit shall
operate under “FAN” mode. Press the “FAN” key to select
from high, medium and low speed.
a) After the unit is connected to
power supply, the air conditioning unit
shall enter the operating status if you
press the ON/OFF key
b) Press the mode key and select the
( ) mode
1２

1３
Loading Batteries Into Remote Controller
• After batteries are installed, the display shall display icons and letter codes of all functions.
• The life of batteries is about 1 year.
• Do not mix new and old batteries or mix different types of batteries in usage
• If the remote controller shall not be used for a long time, take out the batteries to avoid
liquid leakage and any subsequent failure.
• Load two “AAA” batteries (Accessories)

U nit Function
• 7DP - Seven days programmer (Accessory not supplied)
1Unit dispaly
2Single/group display
3Timer week display
4Timer display
5Timer state display
6Timer time period display
7Timer ON/OFF time display
8Unit on display
9Unit off display
10 Clock display
11 Confirm button
12
Decrease button
13
Increase button
14 Cacel/delete button
15
Single/group button
16 Timer/time button
17 ON/OFF button
Composition of programmer wall week
Centralized Control and Week Timer
Functions: The centralized control-
ler and the weekly timer are integra-
ted in the same wire controller. The
system has both the centralized con-
trol and the week timing functions.
Up to 16 sets of units can be control-
led simultaneously by the centralized
controller (weekly timer). The weekly
timer has the function of invalidating
the lower unit. The weekly timing fun-
ction is able to realized four timing
ON/OFF periods for any unit every
day, so as to achieve fully automatic
operation.
This WEEKLY TIMER adopts 485
mode to communicate with manual
control of every duct type unit, and it
can control up to 16 units. Adopting
2-core twisted-pair wire, the lon-
gest communication distance of this
TIMER is 1200m. After connected
to power, the WEEKLY TIMER can
display all connected units (sequence
of unit is determined by code switch
of manual control of every duct type
unit). On and off of every duct type
unit can be done through the Timer
On / Off of this WEEKLY TIMER, and
the button shield operation of manual
control can be done through shield
setting on WEEKLY TIMER. Mode
selection and temperature adjust-
ment and other operations are done
through the manual control at every
unit.
1４

Week timer Manual control Manual control
LCD LCD LCD
16 units in max
Telephone wire box Telephone wire box
Telephone
wire box
Twisted wire with crystal joint
Power
supply
On Off
Power
Longest distance 1200 m
Corresponding relation between code
switch and sequence of unit (NOTE: put-
ting code switch to ON means 0)
Note:
1．For upper unit checks 16 lower units consecutively, there will be no more than 16 seconds delay when setting works till unit responds.
2 Please let us know your requirement before your placing the order, for this WEEKLY TIMER will only be prepared when customer orders
(communication joint with WEEKLY TIMER on manual control had been prepared).
1. Press ▲or ▼to select the unit that needed to be control. It is available to control several units by
Group Control (1~16), or control single unit by Single Control.
2. When selected a certain or several units by Single Control or Group Control, Timer setting and On/off
setting can be set. Timer setting can set 4 on/off times in a day in one week; and on/off setting can be
done by pressing on/off button.
3. Connection between WEEKLY TIMER and manual control is shown as following:
1５

Wire controller (with week timer functions)
• Never install the wire controller in a place where is water leakage.
• Avoid bunping, throwing, tossing or frequently opening the wire controller .
DAY SEG
18 19
1Timing display
2Fan speed display (Auto, High speed, Medium
speed, Low speed)
3Defros ting st atus display
4Energy savingst atus display
5Set temperature display
6Ambient temperatur e display
7Fresh air st atus display (not supplied)
8Mode (cooling, dehumidifying,fan, heating, auto)
10 Sleep st atus display
11 Mode key
12 Set temperature increase key
13 Set temperature decr ease key
14 Fan speed key (fresh air setting)
15 Sleep key (outdoor environment temperature check)
16 Timing key
17 ON/OFF key
Composition of wire controller(Accessory not supplied)
9Failure status display
18 Timer day display
19 Timer segment display
1６

fig 17
Timer setting (Fig. 15, 16, 17)
The timer function of this display board
is invalid when connect with the timer
of the last week, the display board will
be controlled by the week timer.
No matter the unit is turned on or turned off, press
“TIMER”button enter into Timer setting,
then use the “▲”、“▼” buttons to select
the time (As shown In Fig.15),
the setting time (Fig.16) or cancel setting (Fig.17).
Then press “Timer” Button enter into
each item setting.
• Wire controller with week timer function,No.1-No17 is the same as front
• instructions of No18,No.19:
fig 15
fig 16
ＳＥＧ
ＳＥＧ
1７

ｆig 18
ｆｉｇ １９
ｆｉｇ ２０
ＯＮ
ＤＡＹ ＳＥＧ
ＯＦＦ
ＤＡＹ
If enter into timer setting, by pressing
“Mode” button to select the setting item:
Day (Monday to Sunday), Segment
(1-4), Timer (timer on or timer off), the
Minutes and Hours of the time; By
pressing “▲”、“▼” buttons to adjust the
setting, then press the Timer button to
confirm, and press the Timer button once
more to cancel the setting; After the setting
confirmed, the character on displayer will
not blink, it can not be setup; When cancel
the confirmation, there are figure blink, it
can be set up, finally press the “ON/OFF”
button complete the setting and quit, the
timer data will be save. (Fig.18, 19)
If entered into “Timer setting” by pressing
the “Mode” button to select the setting
item: Day (Monday to Sunday), Hours
（0~23）or Minutes (0~59); By pressing
“▲”、“▼” buttons to adjust the setting
items, then press “Timer” button to
confirm, or press the “Timer” button once
more to cancel the setting; After the setting
confirmed, the character on displayer will
not blink, it can not be setup; When cancel
the confirmation, there are figure blink, it
can be set up, finally press the “ON/OFF”
button complete the setting and quit, the
timer data will be save. (Fig. 20)
ＤＡＹ ＳＥＧ
１８

ｆｉｇ ２１
ＤＡＹ
If enter into “Cancel Timer”, by pressing
“▲”、“” buttons to select Week, then
press the “Timer” button to confirm, at this
time, “dd” will display; or press “Timer”
button to cancel the selected day, at this
time “dd” will not display. At last press
“ON/OFF” button complete setting and
quit. (Fig.21)
１９