Sinope TH1300ZB User manual

INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat cover.
Use the screws to secure the thermostat to the
electrical box.
Replace the cover and lock.
Power up the thermostat.
After performing a test sequence, the thermostat should
display the floor temperature. If not, refer to the trouble-
shooting guide in this manual.
1
24
5
6
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat should be made by a
certified electrician and must be installed in conformity
with the national and local Electrical Codes.
Connect the heating floor by using the wire connectors
load / line located on the back of the thermostat. Connect
the ground wire to the screw in the electrical box intended
for this purpose.
Connect the sensor.
(Only for control applications in F mode or with floor limit.)
3
Line
Load
Floor heating
123
456
Sensor
Make sure to firmly tighten the wire connectors for a secure
connection. A loose connection can be a fire hazard.
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
zigbee 3.0
USER SETTINGS
Get the setpoint to its minimum and hold the
button for 10 seconds to access the menu.
Press the or button to change
the setting.
Press the and buttons simultaneously to
save and go to the next parameter. Continue
to press until the end of the list to exit the
menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
10 s ec.
All the parameters of your thermostat can be programmed through the
interface of your Zigbee-compatible gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
Settings which can be modified on the device directly:
Control
Load
Display
Limit Floor Max
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through the application of your Zigbee-
compatible gateway. *
5) Assigning the auxiliary output (A mode):
The thermostat provides an auxiliary output that has three functions
which are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a
heater controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a
heater controlled through an electromechanical relay or equipped with
a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary
output activates the heating device to reach the set temperature. (The
auxiliary output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 sold separately).
OFF function (default): Disables the auxiliary output.
7) Control4 (OFF): The thermostat will connect to a Control4
network system.
Important: This option cannot be changed once the thermostat is
connected to a network (Zigbee or Control4).**
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an
external temperature sensor with the possibility to limit ambient
temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
4) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it
does not exceed the selected limit. Ideal for protecting engineered
wood floors.
Name Parameters & settings Display
Control4
Control4
ON or OFF (default: OFF)
When installing your floor heating system: add a second sensor in
the floor whose tip can be stored in the thermostat housing. This
additional sensor can be plugged in and used as a replacement
without altering your floor heating system.

1st
Hub
2nd
3rd
Trasmitter module IC: 21098-ESPWROOM32 / FCC ID: 2AC7Z-ESPWROOM32
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment OFF and ON, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
For more information, visit our Website:
660-0735-0012-A
CONNECT YOUR THERMOSTAT TO A ZIGBEE COMPATIBLE SYSTEM
DISCONNECT YOUR THERMOSTAT FROM A ZIGBEE COMPATIBLE SYSTEM
Connect your thermostat to the network
by pressing simultaneously on the
and buttons.
On the thermostat display:
Flashes: Connecting
Remains lit: Connected
If the connectivity fails, the symbol will
disappear from the display. Refer to our
Website to troubleshoot the unit.
12
Connect all your thermostats
the same way, by going to the
next closest thermostat.
34
When all the thermostats are
connected, close the connecti-
vity session of your Zigbee
compatible hub.
To disconnect your thermostat from the Zigbee compatible hub, press the and buttons simultaneously for 10 seconds.
The symbol will disappear from the display.
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control an heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 96 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Zigbee profile 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
Initiate the connectivity
session of your Zigbee
compatible hub by
referring to the device's
user guide.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VAC
Baseboard
Convector
Transformer