Sinope TH1123ZB-G2 User manual

Out
TH1123ZB-G2
TH1124ZB-G2
Installation Guide
Smart Thermostat for
Electric Heating
Gateway connection status
Time
(provided by the gateway)
Secondary display:
Setpoint [Set) or outside
temperature [Out]
Ambient temperature
Heating indicator
Make sure that the
breakers for your
heating system are
off at the main
electrical panel to
avoid any risk of
electrick shock.
Replace the cover
and lock
Power up the thermostat.
Unlock and lift the
thermostat cover.
INSTALL YOUR THERMOSTAT
12
45
Out
YOUR SMART THERMOSTAT FOR ELECTRIC
HEATING
Operatlng voltage: 120 / 208 / 240 Vac, 60 Hz
• TH1123ZB-G2 Thermostat
Maximum load:
12.5 A / 3000 W @ 240 Vac
12.5 A / 1500 W @ 120 Vac
• TH1124ZB-G2 Thermostat
Maximum load:
16.7 A / 4000 W @ 240 Vac
16.7 A / 2000 W @ 120 Vac
Minimum load:
Baseboard, convector and radiant ceiling
2 A / 500 W @ 240 Vac
2 A / 250 W @ 120 Vac
Fan-forced convector
4.16 A / 1000 W @ 240 Vac
4.16 A / 500 W @ 120 Vac
Resistive load only
Setpoint range: 5 ˚C to 30 ˚C (41 ˚F to 86 ˚F)
Display range: 0 ˚C to 50 ˚C (32 ˚F to 99 ˚F)
Resolution: ±0.5 ˚C (±1 ˚F)
Storage: -20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Operation: 0 ˚C to 50 ˚C (32 ˚F to 122 ˚F)
Protocol: Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
Compatible with an electric heating system such as:
• Baseboard heater [short cycle]
• Convector [short cycle]
• Fan-forced convector [long cycle)
• Radiant ceiling heating
TECHNICAL SPECIFICATIONS
The installation of this thermostat must be performed by a certified electrician and comply with the
national and local electrical codes and regulations.
Warnings
Use the connectors provided to connect the thermostat wires
to the wires in the electrical box.
Note: The wires of this thermostat are non-polarized.
3
Special CO/ ALR solderless connectors must be used
when connecting with aluminum conductors.
Four-wire installation
Two-wire installation
* Improperly installed electrical wires could burn the wire
connectors.
Make sure to firmly tighten the
wire connectors for a secure
connection. A loose connection
can be a fire hazard.
To install wire connectors,
you must:
Insert the two wires into the wire nut so that their
copper ends are parallel.
Turn the wire connector clockwise until there is
strong tension.
Pull on the threads to make sure they are secure,
leaving no gaps between them. * If the threads
seem to come loose, repeat the process.
1
2
3
3/4"

Out
Connect your thermostat to the network
by pressing the and buttons briefly
and simultaneously.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
Transmitter Module IC: 5123A-GM210P / FCC ID:QOQGM210P
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPÉ TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3 year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged. The obligation of SINOPÉ TECHNOLOGIES
INC., under the terms of this warranty, will be to supply a new unit and this releases the
manufacturer from paying the installation costs or other secondary charges linked to
replacing the unit or the components.
For more information, visit our Website:
660-0300-0001-A
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
CONNECT YOUR THERMOSTAT TO THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
Tap , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Get the app
Follow the steps of the installation wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
1
3
2
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
4
Connect all your devices the same way,
by going to the next closest device.
Hub
2nd
1st
3rd
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. “FACT RST” will appear on the
thermostat's display for approximately 5 seconds.
Get the setpoint to its minimum and hold
the button for 10 seconds to access
the menu.
Press the or button to change the
setting.
Press the and buttons
simultaneously to save and go to the
next parameter.
Continue to press until the end of the list
DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
USER SETTINGS
Out
Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries.
Google Play and the Google Play logo are trademarks of Google Inc.
All of the thermostat's settings can be set through the
Neviweb app.
However, if you have not created your account and wish to
change the temperature format or the control cycle, you need to:
Alimentez le thermostat.
Alimentez le thermostat.
Alimentez le thermostat.
Alimentez le thermostat.
10 s ec.
Alimentez le thermostat.
Out
10 sec.
Alimentez le thermostat.
Parameter# Name
Cycle
SHT (short cycle for electric baseboard)
FAN (long cycle for fan forced heater)
Temperature scale
°C or °F (Default: °C)
Cycle
Display
Units
Cycle
1
2