Sinope TH1400WF User manual

CONNECTION OF THE FLOOR SENSOR
(OPTIONAL)
TH1400WF
Installation Guide
Smart Low voltage Thermostat (24 Vac)
WIRING LAYOUT
ADD YOUR THERMOSTAT TO NEVIWEB
Tap the then select "Add Device"
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to open an account and add
your device.
Follow the steps of the
Installation Wizard
3
3
2
1
INSTALL YOUR THERMOSTAT
Unlock and lift the
thermostat cover.
Depending on the heating system,
insert each wire into its terminal
and screw firmly. (See connection
layouts outlined in the following
pages.)
Use the provided screws and
wall anchors to fix the
thermostat base on the wall.
Replace back and lock the
thermostat cover.
12
45Power up the thermostat.
6
If necessary, mark and drill the
appropriate fastening holes, using the
installation template. If needed, use
the wall anchors included.
3
AUXILIARY OUTPUT
The thermostat provides an auxiliary heating output that
can act as a second stage of heating when controlling
ambient temperature.
If the room temperature is too far from the setpoint or the
main stage of heating has difficulties raising the
temperature, the auxiliary output activates the secondary
heating source to reach the set temperature.
Both outputs can control different types of heating load and
can be configured in the user settings.
Electric baseboard
Electric baseboard
Floor sensor
Electric floor heating
Electric baseboard
Electric floor heating with electric
baseboard on the 2nd heating stage
C
W1
R
W2
S1
S 2
120 V
240 V
347 V
24 V 24 Vac
normally open
Valve
Floor sensor
For use in floor or ambient
mode with floor limit.
Not required for ambient
mode alone.
Hot water valve
Only for control applications in floor (F) mode or with floor limit.
Sensor
TB024B

660-0737-0006-B
10 s ec.
USER SETTINGS PARAMETERS THAT CAN BE CONTROLLED
FROM THE DEVICE (continued):
All of the thermostat's settings can be set through the
Neviweb app. However, if you have not created your
account and wish to change the temperature format or the
control cycle, you need to:
Lower the setpoint to its minimum and hold the button for
10 seconds to access the menu.
Press the or the button to change the setting.
Press the and the buttons simultaneously to save and go
to the next parameter. Continue to press until the end of the list
to exit the menu.
The thermostat features two temperature
control modes:
A mode (default): Regulation of ambient temperature with
the possibility to limit floor temperature through an external
temperature sensor.
F mode: Regulation of floor temperature through an external
temperature sensor with the possibility to limit
ambient temperature.
#
Parameters & settings Display
6
Name
Aux
Cyc
7
Cyc
4
Max
Floor
Max
Air
8
Sens
9
PE
Maximum floor temperature limit
7 °C to 36 °C – (Default: OFF)
5
Min
Floor
Minimum floor temperature limit
5 °C to 36 °C – (Default OFF)
Floor sensor
10K or 12K – (Default: 10K)
Circulator pump's anti-seizure
ON or OFF (Default: OFF)
3
Maximum ambient temperature limit
5 °C to 36 °C – (Default OFF)
Cycle lenght / Main output
15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: 15 min)
Cycle lenght / Auxiliary output
OFF, 15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: OFF)
6) et 7) Main and auxiliary output cycle length
The thermostat has a main and an auxiliary output.
Select the appropriate cycle length based on your
heating system. The selection of an inappropriate
cycle length may damage your unit.
4) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure
it does not exceed the selected limit. This parameter is ideal for
protecting engineered wood floors. (Verify with your flooring
manufacturer to determine heat limit.)
This parameter is only usable when a floor sensor is connected to
the thermostat.
5) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in
order to keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is
connected to the thermostat.
3) Maximum limit of the ambient
temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
PARAMETERS THAT CAN BE CONTROLLED FROM
THE DEVICE (CONTINUED):
9) Circulator pump's anti-seizure
When the thermostat is not heating for an extended period, this
parameter will activate the main output during 1 minute every
24 hours to ensure the hydronic system pump does not seize.
0.15 5 10 15 20 25 30
Convector or baseboard heater
activated by electronic relay (SSR)
Minimum cycle length
Fan-forced convector activated
by electronic relay (SSR)
Fan-forced convector or
baseboard heater activated by
mechanical relay
Hydronic heating pump system
Furnace
TECHNICAL SPECIFICATIONS
Operating voltage: 24 Vac
Maximum load: 1 Amp
Setpoint range: 5 ˚C to 36 ˚C (41 ˚F to 97 ˚F)
Display range: 0 ˚C to 70 ˚C (32 ˚F to 99 ˚F)
Resolution: ±0,5 ˚C (±1 ˚F)
Storage: -20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
Protocol: Wi-Fi
Standard: IEEE 802.11 b/g/n
Frequency: 2.4 GHz
Compatible with:
• Baseboard heater activated by mechanical relay or
electonic relay (SSR)
• Fan-forced convector activated by mechanical relay
or electronic relay (SSR)
• Electric floor heating (activated by a relay)
• Hydronic floor heating
• Hydronic heating system
• Furnace (without fan control)
Transmitter Module IC : 21098-ESPWROOM32 / FCC ID: 2AC7Z-ES-
PWROOM32
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use of the Works with Apple badge means that an accessory has been designed to work
specifically with the technology identified in the badge and has been certified by the developer
to meet Apple performance standards. Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
HomeKit is a trademark of Apple Inc.
Neviweb® is a registered trademark of Sinopé Technologies Inc. in Canada and the United States.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries.
App Store is a service mark of Apple Inc., registered in the U.S. and other countries. Google Play
and the Google Play logo are trademarks of Google Inc.
The Wi-Fi CERTIFIED™ Logo is a certification mark of Wi-Fi Alliance®
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
PARAMETERS THAT CAN BE CONTROLLED
FROM THE DEVICE:
#
Parameters & settings Display
2
Name
Control
1
Temp
Temperature format
°C or °F – (Default: °C)
Control mode of thermostat
A (Air), F (Floor) – (Default: A)
To disconnect your thermostat from the Wi-Fi router press the
and buttons simultaneously for 10 seconds. The
symbol will disappear from the display.
To remove your thermostat from Neviweb, press Delete in
the thermostat settings.
DISCONNECT YOUR THERMOSTAT FROM THE
WI-FI ROUTER OR THE NEVIWEB APP
10 sec.
Controlling this HomeKit-enabled accessory automatically
and away from home requires a HomePod, Apple TV, or
iPad set up as a home hub. It is recommended that you
update to the latest software and operating system.