Sinope TH1300ZB User manual
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 s ec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
INSTALL YOUR THERMOSTAT
Unlock and lift the thermostat
cover.
Warnings
Before starting the installation of your new thermostat, please
make sure that the breakers for your heating system are off at
the main electrical panel!
The installation of this thermostat must be performed by
a certified electrician and comply with the national and
local electrical codes and regulations.
Line
Load
Floor heating
1Connect the sensor.
(Only for control applications in
F mode or with floor limit.)
3
Connect the heating floor by using the
wire connectors load / line located on
the back of the thermostat. Connect the
ground wire to the screw in the
electrical box intended for this purpose.
2
Use the screws to secure
the thermostat to the
electrical box.
4Replace the cover and lock.
5Power up the thermostat.
After performing a test sequence,
the thermostat should display the
floor temperature. If not, refer to
the trouble-shooting guide in
this manual.
6
TH1300ZB
Installation Guide
Smart Floor Heating
Thermostat (3600 W)
USER SETTINGS
USER SETTINGS (continued)
Get the setpoint to its minimum and hold the button for 10 seconds to
access the menu.
Press the or button to change the setting.
All the parameters of your thermostat can be programmed through Neviweb or
the interface of your compatible Zigbee gateway.
However, if your thermostat is not connected to you gateway and you wish to
change the temperature format or the control cycle, you need to:
The following table lists the settings that can be changed directly on
the thermostat.
You can change other settings through Neviweb or the application of your
compatible Zigbee gateway. *
10 sec.
* Available settings may vary depending on your gateway.
** To disconnect a thermostat from a network, refer to the disconnection
procedure on the back of this guide.
When installing your floor heating system: add a second
sensor in the floor whose tip can be stored in the
thermostat housing. This additional sensor can be
plugged in and used as a replacement without
altering your floor heating system.
Sensor
Press the and buttons simultaneously to save and go to the
next parameter. Continue to press until the end of the list to exit
the menu.
Increasing or lowering the temperature
To adjust the temperature, press or . The requested temperature
will blink to confirm the new setpoint.
Sensor
3) The thermostat offers 2 temperature regulation modes:
F mode (default): Regulates the floor temperature by means of an external
temperature sensor with the possibility to limit ambient temperature.
A mode: Regulates ambient temperature with the possibility to limit floor
temperature by means of an external temperature sensor.
6) Maximum limit of the ambient temperature (F mode)
Thermostat limits floor heating so as not to exceed the set ambient
temperature limit
7) Maximum floor temperature limit (A mode)
The thermostat limits floor heating to the set temperature to ensure it does
not exceed the selected limit: Ideal for protecting engineered wood floors.
8) Minimum floor temperature limit (A mode)
The thermostat limits the minimum temperature of the floor in order to
keep it at a comfortable temperature.
This parameter can only be used when a floor sensor is connected to the
thermostat.
9) Assigning the auxiliary output:
The thermostat provides an auxiliary output that has three functions which
are set from the user settings.
15 sec function: Short cycle auxiliary output (15 seconds). Used for a heater
controlled through an electronic relay (SSR).
15 min function: Long cycle auxiliary output (15 minutes). Used for a heater
controlled through an electromechanical relay or equipped with a fan.
In the 15 sec and 15 min functions, the thermostat controls the ambient
temperature with the floor. Once the floor temperature has reached its
limit, if the desired ambient temperature is not reached, the auxiliary output
activates the heating device to reach the set temperature. (The auxiliary
output acts as a second heating stage.)
EXP function: Auxiliary output to connect several heating floors
(TR1310 expansion unit sold separately).
OFF function (default): Disables the auxiliary output.
Settings which can be modified directly on the device:
Control
Min
Max
Load
Display
Max Floor
Max Air
Min Floor
Aux
Sensor
Load power
0 watt to 3600 watt
Temperature format
°C or °F (default: °C)
Control mode
A (Air), F (Floor) (default: F)
Minimum setpoint
5 °C to 36 °C - (default: 5 °C)
Maximum setpoint
5 °C to 36 °C - (default: 36 °C)
Maximum floor temperature
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Maximum limit of the ambient
(Only visible in F mode)
5 °C to 36 °C (default: OFF)
Minimum floor temperature limit
(Only visible in A mode)
5 °C to 36 °C (default: OFF)
Floor sensor
10K or 12K (default: 10K)
Assignment of auxiliary output
OFF, EXP, 15 sec, 15 min (default: OFF)
Name Parameters & settings Display
7
8
9
10
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
CONNECT AN EXPANSION UNIT (TR1310)
CONNECT THE AUXILIARY OUTPUT
It is possible to connect up to 10 expansion units to the
same device. (EXP function)
Second heating stage (15 sec / 15 min functions)
For more information, visit our Website:
660-0735-0022-E
CONNECT YOUR THERMOSTAT TO THE GT130 GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM DISCONNECT YOUR THERMOSTAT FROM THE GT130
GATEWAY OR A COMPATIBLE ZIGBEE SYSTEM
12
Connect all your
thermostats the same way,
by going to the next
closest thermostat.
34
GROUND FAULT PROTECTION
The thermostat is equipped with a ground fault protection that can detect a
current leakage of 5 mA. When a current leakage is detected, the ground fault
protection is triggered and quickly interrupts the power supply to prevent any
serious injuries.
Resetting the ground fault protection
The RESET button warning light turns ON (red) when the ground fault protection is
triggered. If the RESET button warning light turns ON during normal operation of
the thermostat, simply press the RESET button to reset the ground fault protection.
The light will turn OFF. If for any reason this situation occurs again, cut the power
to the heating system from the main electrical panel and ask a qualified
electrician to verify the installation.
Testing the ground fault protection
This thermostat has an Auto Test which
periodically verifies the correct operation of
the protection circuit. You can also do this
manually:
1) Press the TEST button. If the RESET button's
red warning light does not turn ON, the test
has failed. Cut the power to the heating
system from the main electrical panel and
ask a qualified electrician to verify the
installation.
2) Press the RESET button to restart the
thermostat's base.
TROUBLESHOOTING GUIDE
What should I do if the E1F code appears on my thermostat display?
The E1F code means that the thermostat is in “Floor” mode and there is no
connected sensor. If your thermostat is not intended to control a heated floor,
change the thermostat’s control mode for the “A mode”.
TECHNICAL SPECIFICATIONS
Operating voltage: 120/208/240 Vac, 50/60 Hz
Maximum load:
1800 W @ 120 V / 15 A
3120 W @ 208 V / 15 A
3600 W @ 240 V / 15 A
Setpoint range: 5 °C to 36 °C (41 °F to 97 °F)
Display range: 0 °C to 50 °C (32 °F to 99 °F)
Resolution: ±0.5 °C (±1 °F)
Storage: -20 °C to 50 °C (-4 °F to 122 °F)
Auxiliary output: 24 Vac / Vdc / 0.1 A
GFCI protection: Class A (5mA)
Protocol:
Zigbee 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
TR1310 TR1310
To others
TR1310
TH1300ZB
24 VCA
Baseboard
Convector
Transformer
Hub
2nd
1st
3rd
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device does not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty, will
be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
ADD YOUR THERMOSTAT TO THE GT130 GATEWAY
AND NEVIWEB
Tap the , then select "Add Device".
2
1If you do not have an account yet,
download the Neviweb app for iOS or
Android to create an account and add
your device.
Follow the steps of the Installation Wizard.
3
Initiate the connectivity session
by pressing the RF signal button
on the GT130 gateway. The
indicator light will start flashing.
Compatible Zigbee gateway:
refer to the installation guide for
the latter.
Connect your thermostat to the network
by pressing briefly and simultaneously
on the and buttons.
On the thermostat display:
Blinks: Connecting
Remains lit: Connected
If the connectivity fails, the
symbol will disappear from the
display. Refer to our Website to
troubleshoot the unit.
When all your devices are connected, close the
connectivity session of your GT130 gateway or
your compatible Zigbee gateway.
To disconnect your thermostat from the GT130 gateway or a
compatible Zigbee hub, press the and buttons
simultaneously for 10 seconds. The symbol will disappear
from the display.
10 sec.
Other manuals for TH1300ZB
1
Table of contents
Other Sinope Thermostat manuals
Sinope
Sinope TH1400ZB User manual
Sinope
Sinope TH1123ZB User manual
Sinope
Sinope TH1134ZB User manual
Sinope
Sinope TH1500ZB User manual
Sinope
Sinope TH1300NP User manual
Sinope
Sinope TH1500NP User manual
Sinope
Sinope TH1124NP User manual
Sinope
Sinope TH1123ZB-G2 User manual
Sinope
Sinope TH1123WF User manual
Sinope
Sinope TH1400ZB-C4 User manual
Sinope
Sinope TH1123ZB User manual
Sinope
Sinope TH1123ZB-C4 User manual
Sinope
Sinope TH1500WF User manual
Sinope
Sinope TH1300RF User manual
Sinope
Sinope TH1120RF-4000 User manual
Sinope
Sinope TH1400RF User manual
Sinope
Sinope TH1400WF User manual
Sinope
Sinope TH1120-3000 User manual
Sinope
Sinope TH1400ZB User manual
Sinope
Sinope TH1310WF User manual
