Sinope TH1400ZB User manual

AUXILIARY OUTPUT CONNECTION OF THE FLOOR SENSOR
(OPTIONAL)
CONNECT YOUR THERMOSTAT TO A ZIGBEE COMPATIBLE SYSTEM
INSTALL YOUR THERMOSTAT
Unlock and lift the
thermostat cover.
Depending on the heating system,
insert each wire into its terminal
and screw firmly. (See connection
layouts outlined in the following
pages.)
Use the provided screws and
wall anchors to fix the
thermostat base on the wall.
Replace back and lock the
thermostat cover.
12
45Power up the thermostat.
6
If necessary, mark and drill the
appropriate fastening holes, using the
installation template. If needed, use
the wall anchors included.
3
Initiate the connectivity
session of your Zigbee
compatible hub by referring
to the device's user guide.
Connect all your wireless
thermostats the same way,
by going to the next closest
thermostat.
When all the thermostats
are connected, close
the connectivity session
of your Zigbee
compatible hub.
1
2Connect your thermostat to the
network by pressing once the
and buttons at the same time.
On the thermostat display:
Flashes = Connecting
Remains lit = Connected
If the connectivity fails, the symbol will
disappear from the display. Refer to our
Website to troubleshoot the unit.
3
TH1400ZB
Installation Guide
Smart Low voltage Thermostat (24 Vca)
Hub
2nd
1st
3rd
WIRING LAYOUT
The thermostat provides an auxiliary heating output that
can act as a second stage of heating when controlling
ambient temperature.
If the room temperature is too far from the setpoint or the
main stage of heating has difficulties raising the tempera-
ture, the auxiliary output activates the secondary heating
source to reach the set temperature.
Both outputs can control different types of heating load and
can be configured in the user settings.
C
W1
R
W2
S1
S 2
120 V
240 V
347 V
24 V 24 Vac
normally open
Valve
Floor sensor
Electric floor heating
Electric baseboard
Electric baseboard Floor sensor
For use in floor or ambient
mode with floor limit.
Not required for ambient
mode alone.
Electric floor heating with electric
baseboard on the 2nd heating stage
Hot water valve
Electric baseboard
Only for control applications in floor (F) mode or with floor limit.
Sensor
4

The thermostat features two temperature
regulation modes:
Mode Air: Regulation of ambient temperature with the
possibility to limit floor temperature through an external
temperature sensor.
Mode Flr: Regulation of floor temperature through an
external temperature sensor with the possibility to limit
ambient temperature.
6) Main and auxiliary output cycle length
The thermostat has a main and an auxiliary output.
Select the appropriate cycle length based on your
heating system. The selection of an inappropriate
cycle length may damage your unit.
4) Maximum floor temperature limit (Mode Air)
The thermostat limits floor heating to the set temperature to ensure
it does not exceed the selected limit. This parameter is ideal for
protecting engineered wood floors. (Verify with your flooring
manufacturer to determine heat limit.)
This parameter is only usable when a floor sensor is connected to
the thermostat.
9) Circulator pump's anti-seizure
When the thermostat is not heating for an extended period, this
parameter will activate the main output during 1 minute every
24 hours to ensure the hydronic system pump does not seize.
TECHNICAL SPECIFICATIONS
Operating voltage: 24 Vac
Maximum load: 1 Amp
Setpoint range: 5 ˚C to 36 ˚C (41 ˚F to 96 ˚F)
Display range: 0 ˚C to 70 ˚C (32 ˚F to 99 ˚F)
Resolution: ±0,5 ˚C (±1 ˚F)
Storage: -20 ˚C to 50 ˚C (-4 ˚F to 122 ˚F)
Zigbee profile 3.0
Frequency: 2.4 GHz
Transmission power: +20 dBm
Receiver sensitivity: -108 dBm
Compatible with:
• Baseboard heater activated by electronic relay (SSR)
• Baseboard heater activated by mechanical relay
• Fan-forced convector
• Electric floor heating (activated by a relay)
• Hydronic floor heating
• Hydronic heating system
• Furnace (without fan control)
All of the thermostat's parameters can be set through your
compatible Zigbee hub. However, if you have not
connected your wireless network and wish to change the
temperature format or the control cycle, you need to:
Transmitter Module IC : 22394-ZBM1501 / FCC ID:2AK2T-ZBM1501
This device complies with Industry Canada license exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device does not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3-year limited warranty
SINOPE TECHNOLOGIES INC. warrants the components of their products against
defects in material and workmanship for a 3-year period from the date of purchase,
under normal use and service, when proof of purchase of such is provided to the
manufacturer. This warranty does not cover any transportation costs that may be
incurred by the consumer. Nor does it cover a product that has been improperly
installed, misused or accidentally damaged.
The obligation of SINOPÉ TECHNOLOGIES INC., under the terms of this warranty,
will be to supply a new unit and this releases the manufacturer from paying the
installation costs or other secondary charges linked to replacing the unit or the
components.
For more information, visit our Website:
660-0735-0016-B
PARAMETERS THAT CAN BE CONTROLLED
FROM THE DEVICE:
USER SETTINGS
PARAMETERS THAT CAN BE CONTROLLED FROM
THE DEVICE (CONTINUED):
Lower the setpoint to its minimum and hold the button for
10 seconds to access the menu.
Press the or the button to change the setting.
Press the and the buttons simultaneously to save and go
to the next parameter. Continue to press until the end of the list
to exit the menu.
0.15 5 10 15 20 25 30
Convector or baseboard heater
activated by electronic relay (SSR)
Minimum cycle length
Fan-forced convector activated
by electronic relay (SSR)
Fan-forced convector or
baseboard heater activated by
mechanical relay
Hydronic heating pump system
Furnace
To disconnect your thermostat from the Zigbee compatible hub,
press the and buttons simultaneously for 10 seconds.
The symbol will disappear from the display.
DISCONNECT YOUR THERMOSTAT FROM A
ZIGBEE COMPATIBLE SYSTEM
10 s ec.
#
Parameters & settings Display
6
2
Name
Aux
Cyc
Control
7
Cyc
1
Temp
4
Max
Floor
Max
Air
8
Sens
9
PE
Temperature format
°C or °F – (Default: °C)
Maximum floor temperature limit
7 °C to 36 °C – (Default: OFF) (4)
5
Min
Floor
Minimum floor temperature limit
5 °C to 36 °C - (Default OFF)
Floor sensor
10K or 12K – (Default: 10K)
Circulator pump's anti-seizure
ON or OFF (Default: OFF) (5)
Control mode of thermostat
A (Air), F (Floor) – (Default: A)
3
Maximum ambient temperature limit
5 °C to 36 °C - (Default OFF)
Cycle lenght / Main output
15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: 15 min) (1)
Cycle lenght / Auxiliary output
OFF, 15 sec, 5 min, 10 min, 15 min, 20 min,
25 min, 30 min – (Default: OFF) (1)