Sinyifeng Technology SYF-7368 Series User manual

SINYIFENG TECHNOLOGY CO., LTD.
Side 1 of 2
INSTALLATION INSTRUCTIONS
SYF-7368 LED WARNING LIGHTS
Do not install and/or operate this
safety product unless you have read
and understand the safety
information contained in this manual.
Properinstallationof this product requiresthe installerto have a good understandingof automotiveelectronics, systems and procedures.
1. If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other vital parts could be
damagedbythe drillingprocess. Check both sides of the mounting surface before drilling begins. Also de-burr the holes and remove
any metal shards or remnants.Install grommets into all wire passage holes.
2. Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or located in the air bag
deployment area will damage or reduce the effectiveness of the air bag, or become a projectile that could cause serious personal
injuryor death. Refer to your vehicle owner’s manual for the air bag deployment area. The User/Installer assumes full responsibility
to determine proper mounting location, based on providing ultimate safety to all passengers inside the vehicle.
3. Do not attempt to activate or control this device in a hazardous driving situation.
4. This product contains either strobe light(s), halogen light(s), high-intensity LEDs or a combination of these lights. Do not stare
directly into these lights. Momentary blindness and/or eye damage could result.
5. Use only soap and water to clean the outer lens. Use of other chemicals could result in premature lens cracking (crazing) and
discoloration. Lenses in this condition have significantly reduced effectiveness and should be replaced immediately. Inspect and
operate this product regularly to confirm its proper operation and mounting condition. Do not use a pressure washer to clean this
product.
6. It is recommended that these instructions be stored in a safe place and referred to when performing maintenance and/or
reinstallation of this product.
FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR
VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!
Installation & Mounting:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections.
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce
volt- age drop. High ambient temperatures (e.g., under-hood) will significantly reduce the current carrying capacity of wires, fuses,
and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the manufacturer and be
protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation hardware should be used to
anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properlysized to protect the wiring
and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these points
from corrosion and loss of conductivity.
5. Ground termination should only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot environments or operated close
to their capacity.

SINYIFENG TECHNOLOGY CO., LTD. Side 2 of 2
LED WARNING LIGHT SPECIFICATIONS
MODEL SYF-7368A SYF-7368B SYF-7368CSYF-7368G SYF-7368R
1.0 Introduction
The SYF-7368 is LED Warning Lights packaged in a durable polycarbonate base with
a removable lens, modular vibration-resistant power supply and LED lights. The
SYF-7368 is 3.7" high with a base diameter of 5.1". Amber (Yellow), Blue, Clear, Green
and Red lens colors are available.
2.0 Electrical Specifications:
2.1 Input Voltage: 12 ~ 80 Volt Systems
2.2 Input Current: Avg: 0.2 Amps typical on 12 Volt system
2.3 Polarity : Positive or negative ground, polarity protected.
2.4 Connection : Red positive, black negative 18 AWG 8” wires.
3.0 Output Specifications:
3.1 SAE J845 Class 3
3.2 Flash Rate: 8 Flashes (45 FPM)
4.0 Additional Specifications:
4.1 Operating Temperature Range: -20°C (-4°F) to +50°C (122°F).
4.2 Cleaning: Unit may be exposed to spray wash.