Sioux Tools 5202 User manual

Form # ZCE539
Model 5202
Date2-02/A
Micro Polisher
IMPORTANT
Readthese instructionscarefully before installing,operating, servicingor repairingthis
tool.
Keep these instructionsin a safe accessibleplace.
Personal Safety Equipment
YES I 0
Always Read InstructionsBefore Includes:
1 Use - Safety Glasses UsingPowerTools 1 Safety Rules
1 SAFETY MESSAGES 1 A WARNING
Operator Instructions
Safety ruleswhen using a 5202 Micro Polisher
Use - Safety Gloves YES
Use
- Safety Boots
Use
- Breathing Masks YES
Use
- Ear Protectors
- Useaccessoriesratedat least 5,500 RPM.
- Prolongedexposuretovibration may cause injury.
- Readallinstructionsbeforeusingthistool. All operatorsmust
befullytrainedinitsuseandaware
of these safety rules.
- Donotexceedthe maximumworkingair pressure.
- Use personalprotectionequipmentas recommended.
- Somedustcreatedby power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicalsknowntocausecancer,birthdefectsandother
reproductive harm.
- Usecompressedair only atthe recommendedconditions.
- If the tool appears to malfunction, remove from use
immediatelyandarrangefor serviceandrepair. If itisnot
practicalto removetoolfromservice,thenshutofftheair
supply to the tool and write or have written a warning
noteandattach ittothetool.
- If tool is to be usedwith a balanceror other suspension
device, ensure that the tool is firmly attached to the
suspensionlsupportdevice.
- When operating the tool, always keep the body and
I'
articularlythe handsawayfromthe workingattachment
ixedto the tool.
- Thetool isnot electricallyinsulated.Never usethetool if
there is any chance of coming into contact with live
electricity.
- Always when usingthe tool, adopt a firm footing and/or
position and rip the tool sufficiently only to overcome
any reactionkrcesthat may result from the tool doing
work. Do not overgrip.
- Useonly correctspare partsfor maintenanceandrepair.
Do not improvise or make temporary repairs. Major
servicing and repairs should only be carried out by
personstrainedto do so.
- Do not lock, tape, wire, etc. the 'OnIOff' valve in 'On'
position.Thethrottletriggerllever,etc. mustalwaysbefree
to returnto the 'Off' positionwhen released.
- Always shut off the air supply to the tool and pressthe
'OnlOff valve to exhaust the air from the feed hose
beforefitting, removingoradjustingthe
working attachmentfittedto the tool.
- Beforeusingthetool,makesurethat a
shut off device has been fitted to the
supply line and the position is known
and easily accessible so that the air
supply to the tool canbeshut off inan
emergency.
- Checkhoseandfittingsregularlyforwear.
- Take care against entanglement of the
movingpartsof thetoolwithclothing,hair,
ties,cleaningrags,rings,jewelry, watches,
bracelets,etc.This couldcausethe
body
or partsof the bodyto be drawn towards
andincontactwiththemovingpartsofthe
toolandcould
be very dangerous.
- Itisexpectedthat userswill adoptsafe
working practices and observe all
@ Always Wear Safety Goggles
@ Wear HearingProtection
Avoid ProlongedExposure
ffs^ To Vibration
local, regional or country legal requirements when
installing, usingor maintainingthe tool.
- Takecare thattheexhaustair does not pointtowardsany
other person or material or substance that could be
contaminatedbyoil droplets.Whenfirstlubricatinga tool
or if the tool exhaust has a highoil content, do not allow
theexhaustairto comenearvery hotsurfacesor flames.
- Never lay thetool down untilthe workingattachmenthas
ores seen Use
Work
Stations
Putting Into Service
Operating
Dismantling
and Assembly
stoppedmoving.
- When the tool is not in use, shut off the air supply and
pressthrottle triggerllever to drain the supply line. If the
tool isnot to be usedfor a oeriod of time. first lubricate.
disconnectfromairsupplyandstore in
a dryaverageroom
temperatureenvironment.
- If the tool ispassedfrom one user to a new or inexperi-
enceduser, makesurethese instructionsareavailableto
be passedwith the tool.
- Do not remove any manufacturer fitted safety devices
where fitted, i.e., wheel guards, safety trigger, speed
governors, etc.
- Wherever possible,secureworkpiece withclamps,avise,
etc. to make it rigidso it does not move during the work
operation. Keepgood balanceat all times. Donotstretch
or overreach.
- Try to matchthe tool to the work operation.Do not use a
tool that is too light or heavyfor the work operation. If in
doubt, seek advice.
- Ingeneral terms, this tool is not suitable for underwater
useoruseinexplosiveenvironments-seek advicefrom
manufacturer.
- Try tomakesurethatthe work areaisclearto enable the
work task to be performed safely. If practical and
possible, try to clear unnecessary obstructions before
startingwork.
- Always use air hose and couplings with minimumwork-
ing pressure ratings at least
1 112 times the maximum
workingpressure ratingof the tool.
Take Air From Top
All PipeAnd Fittings -
Should Be 112" Or Larger
A
Low Spot To
Compressor Trap Water
with SufficientCapacity
To Maintain Recommended 11 11
Working Pressure At
Drain Daily
L
Recommended Air Supply System Figure 1
PageNo 1
All manuals and user guides at all-guides.com
all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com

All manuals and user guides at all-guides.com