SIRETTA MICA Series Mounting instructions

MICA Series
3G & 4G Dual LAN Industrial Router Range
Software Manual
Rev 1.2

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
2
MICA Series
Software Manual
Table of Contents
Page
Introduction 3
About Siretta 4
General Description 5
Local Conguration 6
Basic Conguration 8
Cellular Network Conguration 9
LAN Settings 12
Dynamic DNS Settings 13
Routing Settings 14
WLAN 15
Basic Settings 15
Wireless Filter Settings 16
Wireless Survey Settings 17
Advanced Network 18
Port Forwarding Settings 18
DMZ Settings 19
Triggered Settings 20
Firewall Settings 21
Serial App Settings 22
UPnp/NAT-PMP Settings 24
Static DHCP Settings 25
VPN Tunnel 26
GRE Settings 26
VPN Client Settings 27
Administration 28
Identication Settings 28
Time Settings 29
Admin Access Settings 30
Schedule Reboot Settings 31
SNMP Settings 32
M2M Access Settings 33
DI/DO Settings 34
Conguration Settings 39
System Log Settings 40
Upgrade Settings 41
System Reboot Settings 41
Debugging 42
Log Settings 42
Ping Settings 42
Restore Factory Settings 43
Via Web Interface 43
Via Router 44
Appendix
(For advanced optional features only) 45
GPS Settings 45
Disclaimer 47
Denitions 48

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
3
MICA Series
Software Manual
The MICA Series is a range of UMTS / LTE routers enabling mobile broadband and
machine to machine (M2M) industrial communication.
This document is aimed at providing guidance when conguring and using the MICA
Series router software.
Conguration of the MICA Series router can be done via the web using any of the
following: Internet Explorer, Firefox, or Chrome. Throughout this document, Internet
Explorer 9.0 is used as the example browser.
Introduction

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
4
MICA Series
Software Manual
Siretta, located in Reading, United Kingdom have been manufacturing antennas,
cable assemblies and cellular modems for over 10 years. We supply our products
globally to many of the world’s leading organisations.
Whether you require an off the shelf or custom solution, Siretta has a wide portfolio of
antenna, RF cable assemblies and modems to t your application.
Our extensive knowledge and experience in the wireless market allows us to support
a wide range of customer applications, focusing on frequencies typically within the
75MHz - 5.8GHz range. These encompass the HF, VHF, ISM, GSM/GPRS/3G/4G
and GPS frequencies as well as industrial WLAN and VHF/UHF antenna/Wi-Fi
antenna solutions.
With a heavy emphasis on design, we have a team of dedicated Application
Engineers and Product Managers, backed up by Field Sales Engineers, who
specialise in wireless applications.
We have made signicant investments in R&D facilities which boast GPS hardware
development equipment and a GSM Pico Cell on site, as well as development
software and a comprehensive suite of Industrial, Scientic and Medical band, and
non ISM band frequency products. We have many technology partners enabling us to
keep at the forefront of the communications industry and offer class leading wireless
solutions.
About Siretta

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
5
MICA Series
Software Manual
General Description
The Siretta MICA router series is a range of high speed industrial cellular routers in a
compact enclosure. The MICA series is offered in 3G / WCDMA/UMTS and 4G / LTE
forms giving reliable, secure and high speed wireless connectivity.
The MICA router range has a number of standard options, such as Wi, GPS, 1xWAN
+ 1xLAN interface etc. Additionally MICA routers are available, as standard with or
without an accessory kit comprising: Wi + GSM antennas, PSU and LAN cable.
VPN features can also be congured in the MICA routers, enabling utilization of a
virtual private network service through a 3G wireless router designed for the stresses
and workload of a modern industrial or commercial environment.
The MICA router series is a high build quality range of routers designed for use in
industrial environments needing high performance and a robust hard enclosure as
standard. The MICA range is designed for remote management, telemetry, condition
monitoring, CCTV, ATMs, vending machine and other M2M applications.
Its compact small size design, enables the MICA Router to easily be embedded into
other equipment or systems. With the GPS option, the MICA router is ideal for eet
tracking or access management.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
6
MICA Series
Software Manual
Local Conguration
The MICA Series router supports conguration by local Ethernet port, you can specify
a static IP or DHCP get IP for your computer.
Default IP address: 192.168.1.1
subnet mask: 255.255.255.0
Follow the steps below to congure your router locally:
Step 1. Click “Start > Control Panel”, nd the “Network Connections” icon and
double click it to enter. Select “Local Area Connection” corresponding to the network
card. (See gure 1 below)
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
12
3 Router Configuration
This Chapter introduces the parameter configuration of the router, the router can be
configured via web internet explorer, Firefox, or chrome. Here we take GUIs 7 system and
Internet Explorer 9.0 as sample.
3.1 Local Configure
The router supports to be configured by local Ethernet port, you could specify a static IP or
DHCP get IP for your computer. The default IP address is 192.168.1.1，subnet mask is
255.255.255.0, please refer to followings:
Step 1 Click “start > control panel”,find “Network Connections” icon and double click it to
enter, select “Local Area Connection” corresponding to the network card on this
page. Refer to the figure below.
Figure 3-3 Network Connection
Step 2 Obtain a IP address automatically or set up IP address,192.168.1.xxx(XXX can be
any number between 2～254)
Step 3 Run an Internet Explorer and visit “http://192.168.1.1/”, to enter identify page.
Figure 1. Network connection
Step 2. Obtain an IP address automatically or set up IP address as: 192.168.1.xxx
(NOTE - XXX can be any number between 2~254)
Step 3. Open Internet Explorer and visit “http://192.168.1.1/”, to enter identify page.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
7
MICA Series
Software Manual
Step 4. User should use the default user name and password when logging in for the
rst time.
Username: admin
Password: admin
Figure 2. User identify interface
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
13
User should use the default user name and password when log in for the first time
Figure 3-4 User Identify Interface
----END
3.2 Basic Configuration
Different software version have different web configuration interface, here take R210
2.6.0.1 version as example.
After visit the WEB interface, you can check the current status of Router, or modify router
configuration via web interface, below is the introduction for the common setting.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
8
MICA Series
Software Manual
Basic Conguration
Different software versions have different web conguration interfaces, in this example
we use version 2.6.0.
After visiting the web interface, you can check the current status of the router or
modify the router conguration via the web interface. Below is the interface displaying
the routers standard settings.
Figure 3. Router status GUI
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
14
Figure 3-5 Router Status GUI
3.2.1 Cellular Network Configure
Step 1 Single Click Basic Network-> Cellular, you can modify relevant parameter
according to the application.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
9
MICA Series
Software Manual
Cellular Network Conguration
Step 1. Select “Basic Network > Cellular” here you can modify cellular and SIM
parameters according to your application.
Figure 4. Dual SIM GUI
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
15
Figure 3-1 Dual SIM GUI
Table 3-1 Cellular Instruction
Parameter
Instruction
Enable
Enable SIM card dial
ICMP check
To enable or disable ICMP check rules. Enable the ICMP check
and setup a reachable IP address as destination IP. Once
ICMP check failed, router will switch SIM card.
SIM Mode
Select the network type
APN
APN, provided by local ISP, usually CDMA/EVDO network do
not need this parameter
User
SIM card user name is provided by ISP
Password
SIM card password is provided by ISP
ICMC Check and Cellular Traffic Check are alternative.
【ICMP Check】
Enable ICMP, Router will automatically check whether the defined IP address is
reachable per 60s. If the IP address is unreachable and ICMP check is timeout at
the first time, it will check 2 time as 3s interval. If the third time is still failed, the
Parameter Instruction
Enable Enable SIM card dial
ICMP check
To enable or disable ICMP check rules. Enable the ICMP check
and setup a reachable IP address as destination IP. Once ICMP
check failed, router will switch SIM card.
SIM mode Select the network type
APN APN, provided by local ISP, usually CDMA/EVDO network does
not need this parameter
User SIM card username is provided by ISP
Password SIM card password is provided by ISP
Table 1. Cellular instruction

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
10
MICA Series
Software Manual
ICMP Check
Enabling ICMP on the router will automatically check whether the dened IP address
is reachable every 60s. If the IP address is unreachable and ICMP check is timed out
at the rst check, it will make two further attempts at 3s intervals. If the IP address
is still unreachable after the third attempt the router will implement the congured fail
action.
The Check IP is a public IP or company server IP address.
Figure 5. ICMP
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
16
router will implement fail action as you configured..
The Check IP is an public IP or company server IP address.
【Cellular Traffic Check】
【Check Mode】there are Rx(Receive), Tx(Transmission) and Rx/Tx check modes.
【Rx】Router will check the 3G/LTE cellular receiver traffic. If no receiver traffic within
the defined check interval, the router will implement the specified action 日
reconnect or reboot.
【SIM Mode】
【Fail Over】SIM card mutual backup. Once SIM card is failed, it will switch to the
SIM2 and work on SIM2. Once SIM2 is failed, it will switch back to SIM1.
【SIM1 Only】Just SIM1 is available.
【SIM2 Only】Just SIM2 is available.
【Backup】SIM1 is the primary SIM. Once SIM1 is failed, it will switch to SIM2 and
work on SIM2 within the defined time. Once the time is over, it will switch back to
SIM1.
Step 2 After Setting, please click “save” icon.
----End
3.2.2 LAN Setting
Step 1 Single Click “ Basic Network>LAN”to enter below interface
Cellular Trafc Check
Check mode: There are Rx(Receive), Tx(Transmission) and Rx/Tx check modes.
RX: The router will check the 3G/LTE cellular receiver trafc. If no trafc is received
within the dened check interval, the router will implement the congured fail action -
reconnect or reboot.
Figure 6. Cellular trafc
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
16
router will implement fail action as you configured..
The Check IP is an public IP or company server IP address.
【Cellular Traffic Check】
【Check Mode】there are Rx(Receive), Tx(Transmission) and Rx/Tx check modes.
【Rx】Router will check the 3G/LTE cellular receiver traffic. If no receiver traffic within
the defined check interval, the router will implement the specified action 日
reconnect or reboot.
【SIM Mode】
【Fail Over】SIM card mutual backup. Once SIM card is failed, it will switch to the
SIM2 and work on SIM2. Once SIM2 is failed, it will switch back to SIM1.
【SIM1 Only】Just SIM1 is available.
【SIM2 Only】Just SIM2 is available.
【Backup】SIM1 is the primary SIM. Once SIM1 is failed, it will switch to SIM2 and
work on SIM2 within the defined time. Once the time is over, it will switch back to
SIM1.
Step 2 After Setting, please click “save” icon.
----End
3.2.2 LAN Setting
Step 1 Single Click “ Basic Network>LAN”to enter below interface

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
11
MICA Series
Software Manual
SIM Mode
Fail over (2 SIMs): SIM card mutual backup. Once SIM 1 fails, it will switch to SIM 2
and work on SIM 2. Once SIM 2 fails, it will switch back to SIM 1.
SIM 1 only: Only SIM 1 is available.
SIM 2 only: Only SIM 2 is available.
Backup: SIM 1 is the primary SIM. Once SIM 1 fails, it will switch to SIM 2 and work
on SIM 2 within the dened time. Once the time is over, it will switch back to SIM 1.
Figure 7. SIM
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
16
router will implement fail action as you configured..
The Check IP is an public IP or company server IP address.
【Cellular Traffic Check】
【Check Mode】there are Rx(Receive), Tx(Transmission) and Rx/Tx check modes.
【Rx】Router will check the 3G/LTE cellular receiver traffic. If no receiver traffic within
the defined check interval, the router will implement the specified action 日
reconnect or reboot.
【SIM Mode】
【Fail Over】SIM card mutual backup. Once SIM card is failed, it will switch to the
SIM2 and work on SIM2. Once SIM2 is failed, it will switch back to SIM1.
【SIM1 Only】Just SIM1 is available.
【SIM2 Only】Just SIM2 is available.
【Backup】SIM1 is the primary SIM. Once SIM1 is failed, it will switch to SIM2 and
work on SIM2 within the defined time. Once the time is over, it will switch back to
SIM1.
Step 2 After Setting, please click “save” icon.
----End
3.2.2 LAN Setting
Step 1 Single Click “ Basic Network>LAN”to enter below interface
After all settings have been congured, click the ‘‘Save’’ icon.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
12
MICA Series
Software Manual
LAN Settings
Step 1. Select “Basic Network > LAN” to enter LAN settings page.
Figure 8. LAN setting GUI
Parameter Instruction
Router IP address Router IP address, default IP is 192.168.1.1
Subnet mask Router subnet mask, default mask is 255.255.255.0
DHCP Dynamic allocation IP service, after enabled it will show the IP
address range and lease options
IP address range IP address range within LAN
Lease The valid time
Table 2. LAN settings instruction
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
17
Figure 3-2 LAN Setting GUI
Table 3-2 LAN Setting Instruction
Parameter
Instruction
Router IP Address
Router IP address, default IP is 192.168.1.1
Subnet Mask
Router subnet mask, default mask is 255.255.255.0
DHCP
Dynamic allocation IP service, after enable, it will show the
IP address range and options of lease
IP Address Range
IP address range within LAN
Lease
The valid time
Step 2 After setting, please click “save” to finish, the device will reboot.
----End
After all settings have been congured, click the ‘‘Save’’ icon.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
13
MICA Series
Software Manual
Dynamic DNS Settings
Step 1. Select “Basic Network > DDNS” to enter the DDNS settings page.
Figure 9. Dynamic DNSS settings
Parameter Instruction
IP address Use default IP 0.0.0.0. For customized protocol, please contact
Siretta representative.
Auto refresh time Set the interval refresh of the DDNS client to 240s or above
Service provider Select the DDNS service provider listed.
Table 3. DDNS settings instruction
After all settings have been congured, click the ‘‘Save’’ icon.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
18
3.2.3 Dynamic DNS Setting
Step 1 Single click “Basic Network->DDNS to enter the DDNS setting page.
Figure 3-3 Dynamic DNS Setting
Table 3-3 DDNS Setting Instruction
parameter
Instruction
IP address
Default is standard DDNS protocol, for customized protocol, please
contact Wlink engineer. Usually, use default IP 0.0.0.0
Auto refresh
time
Set the interval of the DDNS client obtains new IP, suggest 240s or
above
Service
provider
Select the DDNS service provider that listed.
Step 2 Please Click “Save“ to finish.
----End
3.2.4 Routing Setting
Step 1 Single click “Basic Network->Routing to enter the DDNS setting GUI.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
14
MICA Series
Software Manual
Routing Settings
Step 1. Select “Basic Network > Routing” to enter the Routing settings page.
Figure 10. Routing settings
Parameter Instruction
Destination Router can reach the destination IP address.
Gateway Next hop IP address which the router will reach
Subnet Mask Subnet mask for destination IP address
Metric Metrics are used to determine whether one particular route
should be chosen over another.
Interface Interface from router to gateway.
Description Describe routing name.
Table 4. Routing settings instruction
After all settings have been congured, click the ‘‘Save’’ icon.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
19
Figure 3-4 Routing Setting
Table 3-4 Routing Setting Instruction
Parameter
Instruction
Destination
Router can reach the destination IP address.
Gateway
Next hop IP address which the router will reach
Subnet Mask
Subnet mask for destination IP address
Metric
Metrics are used to determine whether one particular route should
be chosen over another.
Interface
Interface from router to gateway.
Description
Describe this routing name.
Step 2 Please Click “ Save “ to finish.
3.3 WLAN Setting
It’s mainly for router which support Wi-Fi, you can modify and configure WLAN
parameter through Web GUI, below is the common setting
3.3.1 Basic Setting
Step 1 Click “WLAN->Basic Setting” to configure relative parameter

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
15
MICA Series
Software Manual
WLAN
Step 1. Select “WLAN > Basic Setting” to enter the WLAN settings page.
Figure 11. WLAN settings
Parameter Instruction
Enable wireless Enable or Disable the Wireless
Wireless mode Support AP, AP+WDS, Bridge, Client, WDS
Wireless network protocol Support Auto, IEEE 11b/g/n selectable
SSID The default is router, can be modied as per application.
Channel The channel of wireless network, keep the default
Channel Width 20MHz and 40MHz alternative
Security Support various encryption methods
Table 5. Routings settings instruction
Conguration of the routers WLAN parameter through Web GUI.
Basic Settings
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
20
Figure 3-5 WLAN Basic Settings GUI
Table 3-5 Basic Setting Instruction
Parameter
Instruction
Enable wireless
Enable or Disable the Wireless
Wireless mode
Support AP, AP+WDS, Bridge, Client, WDS
Wireless Network
protocol
Support Auto, IEEE 11b/g/n selectable
SSID
The default is router, can be modified as per application.
Channel
The channel of wireless network, suggest keep the default
Channel Width
20MHZ and 40MHZ alternative
Security
Support various encryption method
Step 2 Please click “Save” to finish.
----End
3.3.2 Wireless Filter Setting
Step 1 Single click “WLAN > Wireless Filter”.
After all settings have been congured, click the ‘‘Save’’ icon.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
16
MICA Series
Software Manual
Step 1. Select “WLAN > Wireless Filter” to enter the wireless lter settings page.
Figure 12. Wireless lter settings
Parameter Instruction
Disable Filter Enable or Disable the Wireless
Permit on the following
client
Only allow the listed MAC address to connect to the router by
wireless connection
Block the follow Client Prevents the listed MAC address connecting to the router by
wireless connection
Table 6. WLAN basic settings instruction
Wireless Filter Settings
After all settings have been congured, click the ‘‘Save’’ icon.
The Wireless Filter enables permitting/prohibiting specic clients connection to WiFi. This
feature is invalid for wired connections.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
21
Figure 3-6 Wireless Client Filter Setting GUI
The Wireless Filter enable to set the permitted client or prohibit the specific client to
connect the WiFi, However, this feature is invalid for wired connection application.
Table 3-6 ”Wireless Client Filter” Setting Instruction
Parameter
Instruction
Disable Filter
Choose to disable
Permit on the
following client
Only allow the listed MAC address to connect to router by wireless
Block the follow
Client
Prevent the listed MAC address to connect to router by wireless
Step 2 Please click ”save” to finish
----End
3.3.3 Wireless Survey
Step 1 Please click “WLAN> Wireless Survey” to check survey.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
17
MICA Series
Software Manual
Step 1. Select “WLAN > Wireless Survey” to check the survey.
Figure 13. Wireless survey check
Wireless Survey Settings
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
21
Figure 3-6 Wireless Client Filter Setting GUI
The Wireless Filter enable to set the permitted client or prohibit the specific client to
connect the WiFi, However, this feature is invalid for wired connection application.
Table 3-6 ”Wireless Client Filter” Setting Instruction
Parameter
Instruction
Disable Filter
Choose to disable
Permit on the
following client
Only allow the listed MAC address to connect to router by wireless
Block the follow
Client
Prevent the listed MAC address to connect to router by wireless
Step 2 Please click ”save” to finish
----End
3.3.3 Wireless Survey
Step 1 Please click “WLAN> Wireless Survey” to check survey.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
18
MICA Series
Software Manual
Step 1. Select “Advanced Network > Port Forwarding” to enter the port forwarding
settings. You can modify the router name, host name and domain name according to
the application requirement.
Figure 14. Port forwarding settings
Advanced Network
Port Fowarding Settings
Parameter Instruction
Protocol Support UDP, TCP, both UDP and TCP
Src. Addressclient Source IP address. Forward only if from this address.
Ext. Ports External ports. The ports to be forwarded, as seen from the
WAN.
Int. Port
Internal port. The destination port inside the LAN. If blank, the
destination port is the same as Ext Ports. Only one port per
entry is supported when forwarding to a different internal port.
Int. Address Internal Address. The destination address inside the LAN.
Description Remark the rule
Table 7. Port forwarding settings instruction
After all settings have been congured, click the ‘‘Save’’ icon.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
22
Figure 3-7 Wireless Survey Setting GUI
----End
3.4 Advanced Network Setting
3.4.1 Port Forwarding
Step 1 Please click “Advanced Network > Port Forwarding” to enter the GUI, you may
modify the router name, Host name and Domain name according to the
application requirement.
Figure 3-8 Port Forwarding GUI
Table 3-7 “Port Forwarding” Instruction
Parameter
Instruction
Protocol
Support UDP, TCP, both UDP and TCP
Src. Address
Source IP address. Forward only if from this address.
Ext. Ports
External ports. The ports to be forwarded, as seen from the
WAN.
Int. Port
Internal port. The destination port inside the LAN. If blank,
the destination port is the same as Ext Ports. Only one port
per entry is supported when forwarding to a different
internal port.
Int. Address
Internal Address. The destination address inside the LAN.
Description
Remark the rule
Step 2 Please click ”save” to finish
----End

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
19
MICA Series
Software Manual
Step 1. Select “Advanced Network > DMZ” to enter the DMZ settings.
Figure 15. DMZ settings
DMZ Settings
Parameter Instruction
Destination Address The destination address inside the LAN.
Source Address
Restriction
If there is no IP address here, it will allow access to all IP
address. If an IP address is dened, access will be allowed to
this IP address only.
Leave Remote Access Leave remote access
Table 8. DMZ settings instruction
After all settings have been congured, click the ‘‘Save’’ icon.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
23
3.4.2 DMZ Setting
Step 1 Please click “Advanced Network> DMZ” to check or modify the relevant
parameter.
Figure 3-9 DMZ GUI
Table 3-8 “DMZ” Instruction
parameter
Instruction
Destination
Address
The destination address inside the LAN.
Source
Address
Restriction
If no IP address inside, it will allow all IP address to access.
If define IP address, it will just allow the defined IP address
to access.
Leave Remote
Access
Step 2 Please click ”save” to finish
----End
3.4.3 Triggered Setting
Step 1 Please click “Advanced Network> Triggered” to check or modify the relevant
parameter.

A member of the Olancha Group Ltd
Registered in England No. 08405712
VAT Registration No. GB163 04 0349
Siretta Ltd
Basingstoke Road
Spencers Wood
Reading
Berkshire RG7 1PW
sales
fax
email
web
[phone]
[phone]
[email protected]
www.siretta.co.uk
20
MICA Series
Software Manual
Step 1. Select “Advanced Network > Triggered” to enter the triggered settings.
Figure 16. Triggered settings
Triggered Settings
Parameter Instruction
Protocol Supports UDP, TCP, both UDP and TCP
Triggered Ports Trigger ports are the initial LAN to WAN “trigger”.
Transferred Ports Transferred ports are the WAN to LAN ports that are opened if
the “trigger” is activated.
Note Port triggering opens an incoming port when your computer is
using a specied outgoing port for specic trafc.
Table 9. Triggered settings instruction
After all settings have been congured, click the ‘‘Save’’ icon.
Industrial R210 Series Cellular Router User Manual
www.wlink-tech.com
24
Figure 3-10 Triggered GUI
Table 3-9 “Triggered” Instruction
parameter
Instruction
Protocol
Support UDP, TCP, both UDP and TCP
Triggered Ports
Trigger Ports are the initial LAN to WAN "trigger".
Transferred
Ports
Forwarded Ports are the WAN to LAN ports that are
opened if the "trigger" is activated.
Note
Port triggering opens an incoming port when your
computer is using a specified outgoing port for specific
traffic.
Step 2 Please click ”save” to finish.
----End
3.4.4 Firewall Setting
Step 1 Please click “Advanced Network> Firewall” to check or modify the relevant
parameter.