Sirius Satellite Radio Connect SCH1P2 User manual

User Guide
SIRIUS CONNECT™ TUNER

Congratulations on your purchase of the SIRIUS Connect
SCH1P2 Satellite Radio Tuner!
Your new SCH1P2 SIRIUS Connect Satellite Radio Tuner is designed to work with
SIRIUS-Ready receivers. Check the SIRIUS website for model compatibility.
For the latest information about this and other SIRIUS products and accessories, visit
http://www.sirius.com.

[Table of Contents ] 3
Table of Contents
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
COPYRIGHTS & TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . 4
WARNING AND SAFETY INFORMATION. . . . . . . . . . . . . . . . . . . 5
FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Canadian Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PACKAGE CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONNECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Mounting the SCH1 Tuner . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing the Outdoor Antenna . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring the SCH1 Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . 24
Subscribing to the SIRIUS Service . . . . . . . . . . . . . . . . . . . . . 26
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SIRIUS ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

[Copyrights & Trademarks ]
4
Copyrights & Trademarks
© 2008 Sirius Satellite Radio Inc. All Rights Reserved.
® “SIRIUS”, the SIRIUS dog logo, channel names and logos are trademarks of Sirius
Satellite Radio Inc. All Rights Reserved.
™ “SiriusConnect” is a trademark of Sirius Satellite Radio Inc.
Hardware, subscription, and activation fee required. For full Terms & Conditions, visit
http://sirius.com. Prices and programming are subject to change. Not available in HI
and AK. Equipment and subscription sold separately. Installation required with some
equipment.

[Warning and Safety Information ] 5
Warning and Safety Information
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the fol-
lowing two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a CLASS B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.

[Warning and Safety Information ]
6
Canadian Compliance
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Safety Precautions
Be sure to observe the following warnings. Failure to follow these safety instructions
and warnings may result in a serious accident and/or personal injury.
Install the cables and wiring so that it is not crimped or pinched by screws or
sharp metal edges. Route the cables away from moving parts or sharp pointed
edges. This will prevent crimping and damage to the wiring. If the wiring must pass
through a metal hole, be sure to use a rubber grommet to prevent the wire’s insula-
tion from being cut by the metal edge of the hole.
Do not open, disassemble or alter the unit in any way. Doing so may result in fire,
electric shock or product damage.
Do not insert any objects into the unit. Doing so may result in fire, electric shock or
product damage.
Do not install the unit to high levels of humidity, moisture or dust. Doing so can
result in electric shock or product failure.
•
•
•
•

[Package Contents ] 7
Package Contents
The following items are included with your purchase of the SCH1P2. Unpack the kit
carefully and make sure that everything shown is present. If anything is missing or
damaged, or if the kit fails to operate properly, notify your dealer immediately. It is rec-
ommended that you retain the original carton and packing materials in case you need
to ship your kit in the future.
SCH1 SIRIUS Connect TunerSCH1 SIRIUS Connect Tuner RS232 Adapter CableRS232 Adapter Cable
DIN CableDIN Cable RG-174 Adapter CableRG-174 Adapter Cable AC Power AdapterAC Power Adapter

[Package Contents ]
8
Outdoor Antenna and Antenna Installation ItemsOutdoor Antenna and Antenna Installation Items

[Connectors ] 9
Connectors
Figure 1 and the table following identify and describe the connectors of the SCH1
Tuner.
AUDIO
OUT 8 PIN
OPTICAL
R L
DC 5V
ANT
Audio
Connectors
L/R
Optical
Audio
Connector
DIN
Connector
AC Adapter
Connector
Indoor/Outdoor
Antenna
Connector
Description of the SCH1 Connectors
Connector Description
Audio Connector L/R
L/R audio connection for RCA-type audio cables.
(Optional, cable not provided.) (Used when audio is
not provided via the DIN cable.)
Figure 1Figure 1

[Connectors ]
10
Description of the SCH1 Connectors
Connector Description
DIN Connector Connection for the DIN cable to the SIRIUS-Ready
receiver.
Optical Audio Connector
Audio connection when using an optical cable. (Op-
tional, cable not provided.) (Used when audio is not
provided via the DIN cable.)
AC Adapter Connector
Connection for the AC Power Adapter. Note that the
AC Power Adapter is used only when your SIRIUS-
Ready receiver does not supply power to the tuner via
the DIN cable connection.
Indoor/Outdoor Antenna
Connector Connector for the Indoor/Outdoor Antenna.

[Installation ] 11
Installation
It is recommended that prior to starting the installation, you read this installation sec-
tion completely and follow the instructions. In addition, consult the manual of the audio
device to which you will be connecting the SCH1 Tuner to determine the required
installation configuration.
The SCH1 Tuner can be connected to a SIRIUS-Ready receiver using the DIN cable,
or by using the provided RS-232 Adapter Cable.
When connecting using a DIN cable:
If power for the SCH1 Tuner is not provided by your audio device via the DIN cable
connection, you will need to use the provided AC Power Adapter to provide power
for the SCH1 Tuner.
If audio input from the SCH1 Tuner is not supported via the DIN cable connection
of your audio device, you will need to connect the audio output of the SCH1 Tuner
to your audio system via the RCA-type or Optical audio output connectors of the
tuner. (You will need to purchase the appropriate cable separately.)
When connecting using the RS-232 Adapter Cable:
The AC Power Adapter must be connected to the power connector on the RS-232
Adapter Cable.
Note: Do not connect the AC Power Adapter to the SCH1 Tuner when us-
ing the RS-232 Adapter Cable.
The maximum length of RG-6 cable between the Outdoor Antenna and the SCH1
Tuner is 50 ft. For longer lengths the Splitter/Amplifier must be used. When the Split-
ter/Amplifier is used, the maximum lengths of RG-6 cable are 100 ft. from the Outdoor
Antenna to the Splitter/Amplifier, and 50 ft. from the Splitter/Amplifier to the SCH1
Tuner. (Refer to Figures 15 & 16.) RG-6 cable(s) are not provided.
•
•
•
•

[Installation ]
12
Mounting the SCH1 Tuner
Consider the mounting location carefully to be sure that you avoid the following:
Any location where the tuner is exposed to moisture.
Any location where the tuner is exposed to extreme heat.
The tuner may be mounted on a wall with #10 screws, using the slots on the under-
side of the tuner to hang on the tuner on the screws. (Figure 2) Alternately, the tuner
may placed on any flat surface.
SCREW
MOUNTING SLOTS
Installing the Outdoor Antenna
Before installing the indoor/outdoor antenna, read this entire section. To ensure con-
sistent reception of the SIRIUS signal it is important that the antenna be installed and
oriented according to these installation instructions.
Determining a Location for the Antenna
For correct operation and best reception of the SIRIUS signal, it is important that the
•
•
Figure 2Figure 2

[Installation ] 13
outdoor antenna is located in a place where it will have a clear view of the SIRIUS
satellites in the sky. Obstructions such as bushes, trees, other homes or buildings,
overhangs, soffits, chimneys, gables, dormers, etc., will impair or prevent the antenna
from receiving a signal.
The best reception is obtained if the pod portion of the antenna (where the SIRIUS
logo is printed) has a clear 360 degree view of the sky within the cone-shaped area
shown in Figure 3.
No obstructions to the
sky within this area
If you cannot obtain a clear 360 degree view of the sky, then you must at least have a
clear view of the sky in the direction of the SIRIUS satellites, as shown in the following
map diagram.
Figure 3Figure 3

[Installation ]
14
1
23
4
5
HORIZON
SKY
SOUTH
WEST EAST
NORTH
Use the above map and find the area you are located in (1to 5). Then find the direc-
tion in which you need to have a clear view of the sky:
Area 1: You will need a location with a clear view of the sky facing EAST or
NORTHEAST or SOUTHEAST
Area 2: You will need a location with a clear view of the sky facing NORTH or
NORTHEAST
Area 3: You will need a location with a clear view of the sky facing NORTH or
NORTHWEST
Area 4: You will need a location with a clear view of the sky facing WEST or
NORTHWEST or SOUTHWEST
Area 5: You will need a clear view of the sky facing STRAIGHT UP
Figure 4Figure 4

[Installation ] 15
Choose a mounting location for the antenna which has an unobstructed view of the sky
in the direction for your area.
For example, suppose you live in Area 2. You determined that your antenna will need
to have a clear view of the sky facing North or Northeast. The exact direction is
determined by your specific location in Area 2 relative to the Xon the map: If you live
in Texas, you will need a more North facing clear view of the sky whereas if you live in
southern California, you will need a more Northeast facing clear view of the sky.
Figure 5 shows a correct antenna installation for Area 2, with a clear view of the sky in
the North to Northeast direction.
No obstructions to the
sky within the area facing
North to Northeast
N
W E
S
NORTH
Figure 5Figure 5

[Installation ]
16
Antenna Mounting Options
There are three possible mounting options for the outdoor antenna, and the antenna
mounting location you have chosen may determine which mounting methods you can
use:
Wall Mount: Mounting the antenna directly on the side of a home or building.
Roof Mount: Mounting the antenna on the roof of a home or building.
Mast Mount: Mounting the antenna on a mast or pole, such as an existing satellite
TV dish mast, an existing TV antenna mast, or other mast or pole, not exceeding 2
inches in diameter.
Wall Mount
The antenna mounting bracket should be oriented in a vertical position (Figure 6) and
mounted directly to the wall of the building or home using the provided #10 screws.
MOUNTING
HOLES
Remember to avoid blocking the antenna’s view of the sky as described in the previ-
ous section by locating the antenna too high under the eaves or soffit of the home or
building. Refer to Figure 7.
•
•
•
Figure 6Figure 6

[Installation ] 17
UNOBSTRUCTED
VIEW OF THE SKY
INCORRECT CORRECT
UNOBSTRUCTED
VIEW OF THE SKY
CORRECT
OBSTRUCTED
Once you have determined a suitable mounting location, use the mounting bracket as
a template and mark the wall with the location of the four screw holes in the bracket.
Then, using a 3/32 in. drill bit, drill pilot holes in the wall for the screws and then
screw the bracket to the wall.
Roof Mount
When mounting the antenna on the roof of a home or building, mount the antenna as
close as possible to the peak of the roof. It can be mounted on the chimney or on the
soffit of the home or building. Do not mount it directly on the roof surface to avoid
leaks. Remember to avoid blocking the antenna’s view of the sky by locating it where a
chimney, dormer, gable, etc., may obstruct the view of the sky.
Figure 7Figure 7

[Installation ]
18
MOUNTING
HOLES
The antenna mounting bracket should be oriented in a vertical position as shown in
Figures 8 and 9, and mounted directly to the building or home using the provided #10
screws.
Once you have determined a suitable mounting location, use the mounting bracket as
a template and mark the mounting surface with the location of the four screw holes in
the mounting bracket. Then, using a 3/32 in. drill bit, drill pilot holes for the screws. It
may be necessary to fill the holes with a small amount of roof cement or caulk to insure
a watertight installation. Screw the bracket to the mounting surface using the provided
#10 screws.
Figure 8Figure 8
Figure 9Figure 9

[Installation ] 19
Mast Mount
The outdoor antenna can be mounted on most any mast or pole which does not
exceed 2 inches in diameter using the provided U-bolts and mounting brackets,
as shown in Figure 10. If you have a satellite TV dish, the outdoor antenna may be
mounted on the same mast as the satellite dish, but remember that the dish cannot
obstruct the antenna’s view of the sky in the direction which you determined from the
map in the previous section.
To mount the antenna to the mast, you will need to use the two provided U-bolts, the
two mounting brackets, and the four hex nuts. Keep in mind that the antenna cable is
routed under the lower U-bolt, in the slot provided in the antenna base as shown in
Figure 11.
Figure 10Figure 10

[Installation ]
20
Slide one of the U-bolts through the holes at the top of the mounting bracket. Then slide
one of the mounting brackets over the two legs of the U-bolt as shown in Figure 12.
Next, screw the hex nuts on each leg until they are snug. Do not yet tighten the hex
Figure 11Figure 11
Figure 12Figure 12