SIROCO ARIZONA User manual

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
Page 1 of 6
ARIZONA
1 - Device description
2 - Operation
3 - Mounting information
4 - Trou le shooting
5 - Security advice
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 315
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.siroco.fr

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 135
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.si oco.f
Page 2 of 6
1 - Device description
ARIZONA heate consist of a blowe , a coil, a plastic pa t and a emovable f ont plate. Plastic pa t is
made f om polyp opylene. F ont plate is made f om heat and impact esistant ABS. Heate can
ope ate unde th ee diffe ent speeds: a cont ol knob enables to select speed f om f ont plate. The e
a e two input ai supply (on heate side), an output ai supply (on f ont plate) and an input-output
cooling wate supply. Heate including an integ ated valve cont olled f om f ont plate with a knob.
ARIZONA’s f ont plate is available in diffe ent colo s : white, g ey, anth acite o black. Heate can
be equipped with 600, 400 o 300 blowe that supplied in 12 V o 24 V with connections pipes
diamete s of 16 mm.
P oduct pa t numbe s:
ARIZONA 600 ARIZONA 400 ARIZONA 300
Voltage F ont plate
colo Pa t numbe Pa t numbe Pa t numbe
White
0120 0001 0120 0101 0120 0201
G ey
0120 0002 0120 0102 0120 0202
Anth acite
0120 0003 0120 0103 0120 0203
12 V
Black
0120 0004 0120 0104 0120 0204
White
0120 0005 0120 0105 0120 0205
G ey
0120 0006 0120 0106 0120 0206
Anth acite
0120 0007 0120 0107 0120 0207
24 V
Black
0120 0008 0120 0108 0120 0208
Blowe
Ai outlet
Heat exchange
Wate output
Polyp opylene
plastic pa t
Elect ical wi es
(c oss-section 1,5 mm
2
)
Valve cont ol knob
Valve
3 speeds cont ol knob
Wate input
Double poles
connecto
ABS
f ont plate
(supplied sectional)
Knob
s
location

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 135
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.si oco.f
Page 3 of 6
2 - Operation
Cooling wate , befo ehand heated by the vehicle, un on coil. In the same time, fan unit blows f esh
ai th ough the heat exchange . Then, ai tempe atu e ise up. Finally, ai output evacuate hot ai .
Operating conditions:
P oduct must be on a ventilated place.
Ope ating tempe atu e have to be between -30°C and +80°C.
Cooling fluid must be antif eeze and antico osive fo coppe and aluminum. Use a cooling fluid
officially ecognize by automotive manufactu e s.
Technical data:
Type Voltage Elect ical
powe Weight Nominal ai flow
Heating
capacity
L depth
(see §3 step 2)
ARIZONA 600 12/24 V 150 W 2,3 kg 380 m³/h 6,10 kW 227 mm
ARIZONA 400 12/24 V 120 W 2 kg 285 m³/h 5,00 kW 218 mm
ARIZONA 300 12/24 V 55 W 2 kg 200 m³/h 4,35 kW 218 mm
Optimum heating capacity is eached with ai inlet tempe atu e of 0°C, nominal ai flow of 0,5 m
3
/h, f ee ethylene glycol
wate and wate inlet tempe atu e of 100°C.
3 - Mounting information
Fix f ont plate on heate by using 4 supplied s ews (3x15mm). Then, clip cont ol knobs on
its location.
F ont plate
1
4
sc ews
(
3x15 mm
)
Cont ol
knobs
ARIZONA
heate
8 x ø 3,5 mm

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 135
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.si oco.f
Page 4 of 6
Fix p oduct on its cut stand with 8 not supplied sc ews. Blowe moto axis should athe be
in ho izontal position on the vehicle.
Do not d ill heate ’s body so as not to damage heat exchange !
Connect wate input and output by using cooling pipes with co esponding diamete . Using
suitable clamping ings.
Check fo leaks in wate .
Fixation stand
2
3
235 x 170 mm
cut-out
8
not suppl
ied
sc ews
8 Ø 3,7 mm
Clamping
ings
Inlet pipe
3
3
Outlet pipe

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 135
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.si oco.f
Page 5 of 6
Connect double poles connecto acco ding to the following ci cuit diag am. Use at least 1,5
mm² cable c oss-section.
Heate
Fuses values :
Voltage 12 V 24 V
ARIZONA 600 15 A 7,5 A
ARIZONA 400 10 A 5 A
ARIZONA 300 5 A 3 A
4 - Trou le shooting
Fault found Possi le cause Action to take
Check fuse position and ampe age. If necessa y
eplace it. Befo e enew a fuse, always identify
causes.
Fuse defective
Examine blowe s fo a blockage o anothe type of
defect and ectify the cause.
Switch on ignition and/o main batte y switch.
Check batte y connections.
No vehicle powe
Check vehicle ope ating inst uctions fo possible
advice.
Connecting cable
damaged o to n out
Replace cable. Check fo co ect cable outing and
connections acco ding to the ci cuit diag am.
Elect ical connections
eve sed
Check connecting wi es acco ding to the ci cuit
diag am and if necessa y assemble co ectly.
Blowe switch defective Replace the switch with a new o iginal component.
Blockage in fan unit Rectify cause of blockage, e.g. object in impelle . If
necessa y o de new unit.
Blowe not wo king
Blowe moto defective Replace plastic pa t + moto .
No blowe powe Check connection on blowe switch. Blowe doesn’t ope ate
at all speeds Defective esistance Replace plastic pa t + moto .
Blowe only uns at low
and middle speed
Fuse defective Replace fuse.
Unit cannot be switched
off
Sho t-ci cuit in cable Rectify ci cuit diag am. If necessa y, install new
cable.
4
12 V 24 V
Resisto s Resisto s
Moto Moto
Fuse
(see table below)
Black wi e Blue wi e
Red wi e
High speed
Red wi e
High speed
Yellow wi e : low speed
O ange wi e : middle speed
Yellow wi e : low speed
O ange wi e : middle speed
The mo-fuse
The mo-fuse
Fuse
(see table below)

Installation guide
FM 0120 E 1
26/07/10
Ind.
B
SIROCO S.A.S.
10 ue Jean Rostand - Z.I.
BP 135
69745 GENAS Cedex
Tel: [phone]
Fax: [phone]
www.si oco.f
Page 6 of 6
Fault found Possi le cause Action to take
Rated voltage is w ong Rated voltage of unit and on-boa d ci cuit must be
the same. O de new unit.
Ai nozzles closed o
cove ed
Open nozzles o f ee up inlet/outlet openings.
Elect ical wi es a e
unde dimensioned
Install ecommended cable c oss-section.
Blowe only ope ate at
educed powe
Heat exchange seve ely
contaminated
Ca efully clean avoiding damage which can lead to
leaks. WARNING! Obse ve safety inst uctions.
Vehicle engine is not
unning
Sta t engine.
Cooling wate still cold Wait until the engine eaches ope ating tempe atu e
Wate valve closed Open valve. See the vehicle manufactu e ’s ope ating
inst uctions.
Wate lines kinked o
squashed
Eliminate fault by installing co ectly.
Heating doesn’t function
Wate pump p essu e
insufficient
Heat exchange does not have cooling wate flowing
th ough. Install additional pump o mo e powe ful
one.
Volumet ic ai flow f om
blowe is too low
See action to take unde “Blowe ”
Open valve to the maximum. Wate flow ate th ough
heat exchange is too
low
Wate lines kinked o squashed. Relay hoses. Wate
pump p essu e too low (see above fo action).
Flush-out wate ci cuit. Ai in heat exchange
When the pumping p essu e is sufficient the heate is
self bleeding. Install additional o mo e powe ful
wate pump.
Unit is unde dimensioned Install a mo e powe ful unit.
Insufficient pumped
wate p essu e
Install additional pump o a mo e powe ful one.
Reduced heating
pe fo mance
Heat exchange seve ely
contaminated
Ca efully clean avoiding damage which can lead to
leaks.
P oducts which have al eady been pulling appa t a e not cove ed by gua atee.
5 - Security advice
Conside the following advice fo you own safety :
•Installation must only be done by well-fo med and autho ized specialists.
•P oduct must ope ate on a well-ventilated place.
•P oducts have to be used only acco ding to the intended use. P oducts shall not used in
imp ope envi onment. Pay attention to gua antee.
•Befo e using p oducts, ensu e that egulations and laws a e st ictly adhe ed acco ding to the
count y.
•Fo secu ity easons (fi e haza ds), fuses with equi ed ampe age must be used to p otect
elect ical connections.
•Cut elect ical connections befo e wo king on p oduct.
•Do not get into contact with the heat exchange and its connections.
•Do not g ip into the unit and do not put objects inside.