Situ Lighting Plug-in Vision Series User manual


Plug-in Vision Series Art Light Manual
of 1 2
"
4527 Arnold Ave., Naples, FL 34104 • 1-800-561-0492 • www.situlighting.com
Operating Instructions:
Power On/Off and Changing Modes:
•All features of your new Vision Series will be accessed through the
included remote control.
•To turn your light on/off, press the red button on the top left of your
remote control.
•This light has 64 levels of variable light output that can be selected
via the “Bright –“ and “Bright +” buttons on the remote control.
Alternatively, there are shortcuts on the remote control for 100%,
80%, 60%, 40%, 20%, and 10% outputs.
•Remote control is powered by a CR2032 battery. Battery life is
typically 1 – 2 years. Your Vision Series will not function properly
and may not turn on or off when battery needs replacement.
Installation Instructions:
Tools required: Screwdriver, drill (optional for wall mount), hammer (optional), pencil, level, and tape.
Body Adjustment:
•Once mounted, the body of the light can be pivoted to better align
the light output to your artwork.
•We recommend adjusting the body of the fixture so that the beam of
light begins at the top of your artwork (not the frame).
SEE REVERSE SIDE FOR OTHER MOUNTING OPTION
Mounting to Artwork
1. Remove artwork from wall.
2. Locate then mark top center of artwork with pencil
3. Locate the Vision Series Mounting Template provided which fits
your model (17”, 30”, or 43”). If needed, fold or cut the mounting
template to your selected size.
4. Tape the selected template to the back of artwork with the
centerline matched to the center mark on your artwork. Ideally, the
long horizontal line showing with the indicated screw holes should
be ½” – 1” below the top of your frame. With a sharp object or
pencil mark the four mounting block holes.
5. Align the mounting block with the marked holes and attach with 4
small black screws provided. Take care that once the screw is
installed it will not damage the artwork. Do not worry if mounting
blocks are not completely level. Adjustments in step 6 can make up
for slight differences.
6. Unfold the arms of the Vision Series 90˚. Do not tighten or attempt
to tighten the arms. Guide the two arms into the slots of the
mounting bracket and tighten with the included allen wrench.
Height of the light is subjective and should be adjusted as desired.
Raising the light can help eliminate glare.
7. Connect the included power supply to the DC jack attached to the
light. An extension cord is included. Use if needed.
8. Use remote control to dim as desired. Reattach artwork to wall and
enjoy!


Plug-in Vision Series Art Light Manual
of 2 2
4527 Arnold Ave., Naples, FL 34104 • 1-800-561-0492 • www.situlighting.com
Operating Warnings:
•AVOID EYE INJURY - Do not stare directly into beam or shine it directly into anyone's face. Doing so could cause retinal damage.
•Never connect the light to any item other than the supplied power supply. Doing so may damage the product and void your warranty, and
could possibly result in fire, electric shock or other bodily injury.
•Use in a dry and safe location. Our products are meant for indoor and dry locations only.
•Inspect your light carefully before use. Product can become damaged in shipping. Contact us if you have any of the following signs of a
defective product: cuts or damage to electrical cord, damage to light head, or signs of damage on any part of the product.
Precautions:
• AVOID EYE INJURY - Do not stare directly into beam or shine it directly into anyone's face. Doing so could cause retinal damage. • Never
try to disassemble or repair the power supply or this light. Electric shock may result. Contact us for warranty and repairs.• Never alter the plug
on your power supply. If the plug will not fit into the available outlet, have a proper outlet installed by a qualified electrician. Trying to plug
into an improper outlet can result in shock. • Never allow liquids to spill on the power supply or the light and do not connect outdoors, as the
unit is not waterproof. Exposure to rain or other liquid could result in fire or electric shock. • Never connect the light to any item other than the
supplied power supply. Doing so may damage the product and void your warranty, and could possibly result in fire, electric shock or other
bodily injury. • Never use a power supply with a damaged or worn power cord or plug. This could result in electric shock, burns or fire. Contact
us to obtain a replacement.
PROTECTION OF CHILDREN
• This product is not designed, intended or recommended for children.
• Never allow children to play with, or otherwise handle or operate, the light, its battery or charging apparatus, as injury to themselves or others
could result.
• Keep all accessories and components out of the reach of small children. Small parts, in particular, might present a choking hazard to children.
Wall Mount (recommended)
1. Using a pencil, mark your wall at center and top of your artwork.
2. Remove artwork from wall.
3. Locate the Vision Series Mounting Template provided which fits your
model (17”, 30”, or 43”). If needed, fold or cut the mounting template
to your selected size.
4. Using a level, tape the selected template to the wall with the centerline
matched to the center mark made on your wall. The horizontal line with
indicated mounting hole positions should be ½” – 1” below the mark
previously drawn. With a sharp object or pencil mark the four
mounting block holes (two on each side). Do not worry if mounting
blocks are not completely level. Adjustments in step 7 can make up for
slight differences.
5. Drill through the 4 holes using a 3/16” bit.
6. Place a dry wall anchor (included) in each hole then attach the
mounting block with the two long steel screws provided.
7. Unfold the arms of the Vision Series 90˚. Do not tighten or attempt to
tighten the arms. Guide the two arms into the slots of the mounting
bracket and tighten with the included allen wrench. Height of the light
is subjective and should be adjusted as desired. Raising the light can
help eliminate glare.
8. Connect the included power supply to the DC jack attached to the light.
An extension cord is included. Use if needed.
Programming Remote Control to Operate Additional Lights:
1) Unplug the power into the dimmer module (small white box) for 5 or more seconds.
2) Reconnect power then immediately press and hold the 100% and 60% buttons for 1 second.
3) The remote is now programmed to the new light.
4) Repeat the process as necessary to continue programming the remote control to other lights.