iSolution IMOVE 250W User manual

iMove 250W Moving Wash
User Guide
BEGLEC cva – ‘t Hofveld2 – 1702 Groot Bijgaarden Belgium
WWW.BEGLEC.COM 1-
TABLE OF CONTENTS
1.Safety Instruction
2.Technical Specification
3.Lamp
4.How To Set The Unit
4.1 Control Panel
4.2 Main Function
4.3 Home Position Adjustment
5.How To Control The Unit
5.1 Master/Slave Built-In Preprogrammed Function.
5.2 Easy Controller
5.3 iSolution Operation / DMX Controller
5.4 DMX512 Configuration
5.5 DMX512 Connection
6.Troubleshooting
7.Fixture Cleaning

2-
1. Safety Instruction
WARNING
Please keep this User Guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the unit.
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
The unit is designed for use with the MSD 250/2 or NSD250/2. Do not use any other
type of lamp.
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
The unit is for indoor use only. Use only in a dry location.
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
Disconnect main power before fuse/lamp replacement or servicing.
Replace fuse/lamp only with the same type.
Make sure there are no flammable materials close to the unit while operating, as it is
fire hazard.
Use safety chain when fixes this unit. Don’t handle the unit by taking its head only,
but always by taking its base.
Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is
higher than this.
Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand
during its operation, and allow about 15 minutes to cool down before replacing bulb
or serving, as the unit could be very hot.
In the event of serious operating problem, stop using the unit immediately. Never try
to repair the unit by yourself. Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance
center. Always use the same type spare parts.
Don’t connect the device to any dimmer pack.
Do not touch any wire during operation as high voltage might be causing
electric shock.
Please read carefully the instruction, which includes important
information about the installation, usage and maintenance.
3-
Warning
zTo prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
zNever touch bulb with bare fingers, as it is very hot after using.
zHot lamp explosion hazard. Do not open the unit within five minutes after switching off.
zDo not start on the unit without bulb enclosure or housing are damaged.
zThe housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
zDo not look directly at the light while the bulb is on.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt any
repairs yourself. In the unlikely event your unit may require service, please contact your
nearest dealer.
Installation
The unit should be mounted via its mounting system ( as shown below ) on the bottom of the
base. Use clamps to fix the unit to truss. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. Always ensure that the structure to which you are
attaching the unit is secure and is able to support a weight of 30 kgs for each unit.

4-
2. Technical Specification
Power supply
- AC 120V ~ 60Hz / 230V ~ 50Hz
Lamp
- Discharge lamp MSD 250/2 GY 9.5
Optical system
- High efficiency optical system
- High quality optical lens and dichroic colors
- Manually adjustable beam angle: 16 ~26
Shutter/Dimmer
- Blackout, 0~100 smooth dimming and strobe speed variable(1~10 flashes per
second).
Color wheel
- Independent color wheel with 6 dichroic colors plus white.
- Color wheel rotates with variable speed, giving rainbow effect.
CMY Mixing system
-Cyan: 0 ~ 100%, Magenta: 0 ~ 100%, Yellow: 0 ~ 100%
Effect Wheel
- Frost filter and beam shape effect
Movement
- Pan: 540° in 2.8 second.
- Tilt: 270° in 1.6 second.
DMX Channels
- Standard DMX512 signal addressing and can be controlled by any universal DMX
controller.
16 Channels:
Channel 1 = Pan Channel 9 = Yellow
Channel 2 = Tilt Channel 10 = CMY color Mix
Channel 3 = Pan/Tilt Speed Channel 11 = CMY Speed
Channel 4 = Dimmer Channel 12 = Effect Wheel
Channel 5 = Shutter Channel 13 = Dimmer
Channel 6 = Color Channel 14 = Pan 16 bit
Channel 7 = Cyan Channel 15 = Tilt 16 bit
Channel 8 = Magenta Channel 16 = Lamp On/Off/Reset
5-
8 Channels:
Channel 1 = Pan
Channel 2 = Tilt
Channel 3 = Shutter
Channel 4 = Effect wheel
Channel 5 = Color
Channel 6 = CYM Color Mix
Channel 7 = Dimmer
Channel 8 = CMY Speed
Dimension: 428 x 369 x 481 mm (L x W x H)
Weight: 24.2 kg
Luminous intensity:

6-
3. Lamp
Because of its high internal pressure, there might be a risk that the Discharge lamp
would explode during operation. The lamp emits intense UV radiation which is harmful
to the eyes and skin. The high luminance of the arc can cause severe damage to the
retina if looks directly at the lamp.
Discharge lamp:
MSD 250/2 GY 9.5
1.Always switch off the main supply and never handle the lamp or luminaries when is
hot.
2.Do not touch the bulb with bare hands. If this happens, clean the lamp with denatured
alcohol and wipe it with a lint free cloth before installation.
3. The lamp generates UV radiation. Never operate the lamp without appropriate shielding.
4. When burning, the lamp operates at high pressure and there is a slight risk of arc tube
rupture. The risk increases with age, temperature and improper handling of the lamp. Do
not use the lamp any longer than its specified life.
5. Make sure the lamp is located in the center of the reflector for the best spot. Adjust lamp
position by screws A, B and C.
In case of replacement of the lamp or maintenance, do not open the
fixture within 15 minutes until the unit cools down after switching off.
7-
4. How To Set The Unit
4.1. Control Panel
Display
To show the various menus and the selected functions .
LED
DMX On DMX input present
MASTER On Master mode
SLAVE On Slave mode
SOUND Flashing Sound activation
Button

8-
MENU To select the programming functions
DOWN To go backward in the selected functions
UP To go forward in the selected functions
ENTER To confirm the selected functions
Remote controller input
By connecting to the 1/4” microphone jack to control the unit for Stand by, Function, and
Mode function.
Sensitivity
To adjust the sound-receiving sensitivity .
Microphone
To receive audio signal for sound activation .
DMX input/output
For DMX512 link, use 3-pin XLR plug cable to link the unit together.
9-
4.2. Main Function
To select any of the pre-set functions, press the MENU button up to when the required one
is shown on the display. Select the function by ENTER button and the display will blink. Use
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
any change after idling 8 seconds. To go back to the functions without any change press the
MENU button. The main functions are shown below:
MENU
Self-Test
Reset
Fixture Hours
Display Inversion
Display Normal
Tilt Inversion
Tilt Normal
Pan Inversion
Pan Normal
Slave mode " 2 Light Show "
Slave Mode " Normal "
DMX512 Address Setting
Blackout Mode " No Blackout "
Blackout Mode " Yes Blackout "
LED on
LED off
Setting 16 Channel
Setting 8 Channel
Show mode 2
Show mode 1
Show mode 3
Show mode 4
Ambient temperature of lamp
Lamp off
Lamp on
DMX512 Address Setting
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press the ENTER button to setup or automatically
return to the main functions without any change after 8 seconds. To go back to the functions
without any change press the MENU button again.

10-
Channel Mode
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (16
Channel ) or (8 Channel) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Show Mode
Press the MENU button up to when the is showing on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (show 1)
or (show 2) or (show 3) or (show 4) mode. Once the mode has
been selected, press the ENTER button to setup or automatically return to the main
functions without any change after 8 seconds. To go back to the functions without any
change press the MENU button again.
Show 1 mode - Fixture is placed on the floor. Tilt movement angle 210°.
Show 2 mode - Fixture is fixed under ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on the speaker, The spot is always projecting
to the audience’s direction; i.e in front of the stage. Pan movement angle ( left to
right to left ): 160°. Tilt movement angle: 90° ( 60° above horizon; 30°
below horizon.)
Show 4 mode - Fixture is fixed under ceiling. The spot is mainly projecting in
front of the stage. Pan movement angle ( left to right to left ) :160°. Tilt movement
angle: 90° ( vertically, front 75°; back 15° )
Slave Mode
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal)
or (2 light show) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
11-
Blackout Mode
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (yes
blackout) or (no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
after 8 seconds. To go back to the functions without any change press the MENU button
again.
Pan Inversion
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal)
or (pan inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Tilt Inversion
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (normal)
or (tilt inversion) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Led Display
Press the MENU button up to when the is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or (Led off) mode. Once the mode has been selected, press the ENTER
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
Display Inversion
It is good for you to install the unit on the floor or under ceiling. Press the MENU button up to
when the is blinking on the display. Use the ENTER button to change to the mode

12-
(display inversion), It will automatically store after 8 seconds. Or press the ENTER
button again return to the mode (display normal). To go back to the functions press
the MENU button.
Display normal mode for the fixture putting on the floor.
Display inversion mode for the fixture fixing under ceiling.
Self-Test
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the unit will run self-test by built-in program. To go back to the functions press the
MENU button again.
Ambient temperature of lamp
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the ambient temperature of lamp will show on the display. To go back to the
functions press the MENU button again.
Fixture Hours
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button again.
Lamp Display
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select the (Lamp on)
or (Lamp off) mode. Once the mode has been selected, press the ENTER button to
setup or automatically return to the main functions without any change after 8 seconds. To
go back to the functions without any change press the MENU button again.
Reset
Press the MENU button up to when the is blinking on the display. Pressing ENTER
button and all channels of the unit will return to their standard position. To go back to the
functions press the MENU button again.
DMX RESET :
13-
Set DMX value of channel 8 and channel 16 to 255, then all channels of the unit will return to
their standard home position.
4.3 Home Postion Adjustment
Press MENU button for at least 5 seconds into offset mode to adjust the home position, the
functions are shown below:
MENU
Pan offset(0~512)
Tilt offset(0~2048)
Pan offset
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display
will blink. Use DOWN and UP button to adjust the pan home position. Once the position has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.
Tilt offset
Press the MENU button for at least 5 seconds into offset mode, use DOWN and UP button
up to when the is shown on the display. Pressing ENTER button and the display
will blink. Use DOWN and UP button to adjust the tilt home position. Once the position has
been selected, press the ENTER button to setup or automatically return to the offset
functions without any change press the MENU button again, To go back to the main
functions without any change after 8 seconds.
5. How To Control The Unit
You can operate the unit in three ways:
1. By master/slave built-in preprogram function
2. By easy controller
3. By IL-0824 ( please refer to the user guide of iLead controller ) or universal DMX

14-
controller
No need to turn the unit off when you change the DMX address, as new DMX address
setting will be effected at once. Every time you turn the unit on, it will show 2500 on the
display and move all the motors to their ‘home’ position and you may hear some noises for
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built-in
programs.
5.1. Master/Slave Built-In Preprogrammed Function
You can select blackout mode in (yes blackout) or (no blackout)
mode while the unit is turned on. By linking the units in master/slave connection, the first unit
will control the other units to give an automatic, sound activated, synchronized light show.
This function is good when you want an instant show. You have to select show (show 1, 2, 3,
4) modes by easy controller . Its DMX input jack will have nothing plugged into it, and Its
master LED will be constantly on and sound LED will flash to the music. The other units will
have to set in slave mode and select (normal) or (2 light show)
mode, Their DMX cables plugged into the DMX input jacks (daisy chain) and the slave LED
lights will constantly on.
2-light show
In (slave mode), means the unit works normally and means
2-light show. In order to create a great light show, you can set on the second unit to
get contrast movement to each other, even if you have two units only.
15-
5.2. Easy Controller
The easy remote control is used only in master/slave mode. By connecting to the 1/4”
microphone jack of the first unit, you will find that the remote control on the first unit will
control all the other units for Stand by, Function and Mode.
Stand by Blackout the unit
Function
Strobe
1. Color sync. strobe
2. Sync. strobe
3. Two-light strobe
X/Y moving show pattern
selection
( Show 1 ~ Show 4 )
Please refer to 4.2. Main
Functions- Show mode
Color selection X/Y moving setting
1.Pan position
2.Tilt position
3.Dimmer
First set Master unit,
then set Slave units’
position
Mode Sound 1
(LED off )
Sound 2
(LED normal blinking)
Slow/Sound 3
(LED on)
Position/ Latch
(LED fast blinking)
5.3.1 iSolution Operation
·Consistent DMX configuration enable iRock and iShow to be linked together and controlled
at the same time.
·DMX address can be set remotely by iLead controller ( please refer to the user manual of
iLead controller ). No need to calculate the DMX channels of each fixture in the chain.
·Automatic switching between DMX function and built-in stand alone programs.
5.3.2 DMX Controller
If you use a universal DMX controller to control the units, you have to set DMX address from
1 to 512 channel so that the units can receive DMX signal.
Press the MENU button up to when the is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
Once the address has been selected, press and keep ENTER button pressed up to when
the display stops blinking or storing automatically 8 seconds later. To go back to the
functions without any change press the MENU button again.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
16 Channels：

16-
8 Channels
You have to set the fixture DMX address in 8 channels mode when you use IL-0824
controller. DMX address can be set remotely by IL-0824 controller. No need to calculate the
DMX channels of each fixture in the chain.
Please refer to the following diagram to address your DMX512 channel for the first 4 units.
8 Channels：
17-
5.4. DMX512 Configuration

18-
iii.) For DMX Reset, put DMX value of CH-8 & CH-16 to 255.
19-
5.5. DMX512 Connection
The DMX512 is widely used in intelligent lighting control, with a maximum of 512
channels.
1. If you use a controller with 5 pins DMX connector, you need to use a 5 to 3 pin adapter.
2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
in the DMX-output of the last unit.
3. Connect the unit together in a “daisy chain” by XLR plug from the output of the unit to
the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX512
is a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
connectors can easily distort the signal and shut down the system.
4. The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
5. Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6. The end of the DMX512 system should be terminated to reduce signal errors.
7. 3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

20-
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
6. Troubleshooting
Following are a few common problems that may occur during operation. Here are
some suggestions for easy troubleshooting:
A. The unit does not work, no light and the fan does not work
1. Check the connect power and main fuse.
2. Measure the mains voltage on the main connector.
3. Check the power on LED.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of
the unit or the previous one.
4. Try to use another DMX controller.
5. Check in the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the unit. Set the proper address.
D. No response to the sound
1. Check the unit that is not receiving DMX signal.
2. Check microphone to see if it is good by tapping the microphone
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
F. The lamp is cutting out intermittently
21-
1. The lamp is not working well. Check the main voltage either too high or too low.
2. Internal temperature may be too high. Check and if necessary replace the fan on the
head.
G. If The pan belt is broken
1. Turn off the main power.
2. Unscrew all the screws (A) and open the base-housing cover (B).
3. Unscrew all the screws (C) and open the arm cover (D).
4. Unplug all the connect wires that from the arm to the bottom.
5. Unscrew the screws (E) and remove the fixture head.
6. Loose the screws (F), then loose the screws (G).
7. Change a new belt (H) , put the belt around the axis gear and motor gear.
8. Screwed the screws (G), install the new belt and adjust the belt tension properly. Note:
do not fix belt too tight as it is easy to rupture.
9. Plug all the connect wires back that from the bottom to the arm.
10. Reverse the procedures from point 5 to point 2.
A
G
H
F
A
B
B
A
C
D
E
D
C

22-
Pay attention to the belt tension when install the belt.
Please refer to the photos below:
G
F
Photo 1
Adjust belt tension through loose the screw
Photo 2
23-
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
yClean with soft cloth using normal glass cleaning fluid.
yAlways dry the parts carefully.
yClean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
y
EC Declaration of Conformity
We declare that our products (lighting equipments) comply with the following
specification and bears CE mark in accordance with the provision of the
Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements