SKUTCH CK-1P4 User manual

Page 1 of 4
"Telecommunication Products to solve Telecommunication Problems"
CK-1P4
Promotion-On-Hold Module
(For Panasonic
KX-TG6700B and KX-TG6702B)
Introduction
Thank you for purchasing the
Skutch CK-1P4 Promotion-On-
Hold Module. The CK-1P4 is a
true plug and play device. The unit
does not require any "Learning" to
operate. When a call is placed ON
HOLD from the base set, or any one
of the cordless phones, the caller
will hear the Promotion-On-Hold
audio. When the line is re-
answered, the audio automatically
stops. It's that simple!
NOTE: You can NOT use the
“Transfer to Answering System”
with this module. This is ONLY
when you transfer a call to the
answering device, AFTER you have already answered and talked to the person! When a
call is answered by the answering device, the Answering System works perfectly.
Installation
1- Position the CK-1P4 black box under
the base telephone with the jacks facing
towards the back of the phone. (See Fig.
1).
Black Box
CK1P4
Power Cube
Sensor Board
Short Mod Cord
Sensor Cable
Audio Cord (For CD Player NLY!)
Connect to Wall Jack
To Audio Source
LINE 1 /2 LINE 2
Fig. 1

Page 2 of 4
2- Connect the short modular
cord [1&2 Phone on CK-1] to
[LINE 1/2 on Phone].
3- Connect the audio cord from
your audio source, to the
AUDIO IN jack on the back of
the CK-1 box. For DIGITAL
PLAYERS use the cable that
comes with the player.
4- Connect a MOD cord from
Telephone Wall Jack 1&2 to
[1&2 Line on CK-1].
5- Make sure that the surface area
of the base phone, where the
sensor board is to be mounted, is
clean and free of all dust and oil
film. Locate the CK-1P4
"SENSOR BOARD", peel off the
green/white protector papers from
the bottom of the sensor board,
and carefully place it OVER the
LINE 1 and LINE 2 lights on the
Panasonic base set as shown in
Fig. 2 and Fig. 3. Make sure that
you align the SILVER DOTS on
the Sensor Board, directly over
the IN-USE lights on the phone.
6- Connect the Sensor Cable to
the Sensor Board as shown in Fig.
4.
7- Connect the POWER CUBE
from the CK-1 Black Box to
115VAC power. That's it!
Testing the System:
1- Pickup line 1 on your
telephone. The No."1" LED on
the CK-1P4 Sensor Board should
Align by centering Silver Dots
over IN USE lights on phone.
Silver Dots
IN-USE
Lights
Fig. 2
Fig. 3
Sensor Board Mounted
Fig. 4

Page 3 of 4
light up.
2- Repeat this test for line 2. If both lines light up when picked up, the CK-1 is working
properly. If either light does not light up, then
a) Make sure that the CK-1P4 and Phone is connected to power.
b) Make sure that the SENSOR BOARD is aligned properly.
Lights on CK-1 Box.
When you place a line on HOLD, the corresponding LED on the rear of the CK-1P4 box
lights up to confirm the Promotion-On-Hold condition.
Using Other models of telephones
The CK-1P4 will ONLY provide Promotion-On-Hold audio when a call is placed ON
HOLD from the KX-TG6700 base or any of it's cordless telephones. Only ONE KX-
TG6700 base unit can be used. A maximum of 8 cordless phones can be used with one
KX-TG6700 base phone. Other models of telephones can be used with the KX-TG6700,
but the Promotion On Hold audio will not be played to calls placed ON HOLD from
these telephones.
Tech Support - 916-786-6186
If you have any problems getting the unit to work properly feel free to give us a call.
Technical Support is available between the hours of 7:30 AM and 4:30 PM Pacific Time,
Monday through Friday.
•ONE YEAR LIMITED WARRANTY
This SKUTCH PRODUCT is warranted against defects for a period of one (1) year from the date of the
original invoice. Within this period, we will repair it without charge for parts and labor. To obtain
warranty service the product must be returned, at the customer's expense, to SKUTCH Electronics along
with a copy of the original invoice. After the unit has been repaired, SKUTCH will ship the PRODUCT
back via UPS GROUND service at our expense. If any other form of return shipment is requested, the
customer will pay for 100% of the shipping cost.
This Warranty does not apply if in the sole opinion of SKUTCH Electronics, the PRODUCT has been
damaged by lightning or any other Acts of God, or by accident, misuse, neglect, or improper packing,
shipping, modification or servicing by other than an authorized SKUTCH Service Center.
EXCEPT AS SPECIFICALLY PROVIDED IN THIS AGREEMENT, THERE ARE NO OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OR MERCHANTABILITIES OR FITNESS FOR A PARTICULAR PURPOSE AND IN
NO EVENT SHALL SKUTCH ELECTRONICS BE LIABLE FOR LOSS OF PROFITS OR BENEFITS,
INDIRECT, SPECIAL, CONSEQUENTIAL OR OTHER SIMILAR DAMAGES ARISING OUT OF
ANY BREACH OF THIS WARRANTY OR OTHERWISE.

Page 4 of 4
ACTA Statement
This equipment complies with Part 68 of FCC rules and the requirements
adopted by ACTA. On the bottom side of this equipment is a label that contains, among
other information, a product identifier in the format US: AAAEQ##TXXXX. If requested,
this number must be provided to the telephone company.
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and requirements
adopted by the ACTA. A compliant telephone cord and modular plug is provided with
this product. It is designed to be connected to a compatible modular jack that is also
compliant. See installation instructions for details.
The REN is used to determine the number of devices that may be connected to a
telephone line. Excessive RENs on a telephone line may result in the devices not ringing
in response to an incoming call. In most but not all areas, the sum of RENs should not
exceed five (5.0). To be certain of the number of devices that may be connected to a
line, as determined by the total RENs, contact the local telephone company. For
products approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is
separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company
will notify you in advance that temporary discontinuance of service may be required. But
if advance notice isn't practical, the telephone company will notify the customer as soon
as possible. Also, you will be advised of your right to file a complaint with the FCC if you
believe it is necessary.
The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information,
please contact our company. If the equipment is causing harm to the telephone network,
the telephone company may request that you disconnect the equipment until the
problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public
utility commission, public service commission or corporation commission for information.