SkyLink SW-318 User manual

You will see10connectors. Forconnectors “1” to “9”, the settings must
match with those of the transmitter.
For connector “10” on the receiver, set the connector on “+” if you
are using button “1” to control this receiver. If you are planning to
use button “2” to control this receiver, you need to remove this
connector. See diagram below.
It is recommended to randomly set the operation code for your remote
control to avoid interference from other devices. Follow the instructions
below to change the operation code.
Pry off the battery cover on the transmitter
with a coin, as shown.
You will see 9 connectors labeled from
“1” to “9”, as shown.
You can randomly remove some of these
connectors, leaving some connectors in place.
A connector can be removed with the clip, as shown.
If the connector is placed on the top and middle posts, that columnis
set on “ + ” . If the connector is placed on the middle and bottom posts,
that column is set on “ - ”. If the connector isremoved completely,
(not placed on any posts), it is set to “ 0 ”. (see diagram for examples
of how to set a column to the three different positions).When
removing a connector to set a column to “0” position, save the con-
nector in case you change the code at a later date.
After setting up the code connectors on the transmitter, you
are ready to set the same code on the receiver.
BATTERY
1. INTRODUCTION
Skylink®Wireless Switch Model SW-318
2. SET UP THE OPERATION CODE FOR BOTH
TRANSMITTER AND RECEIVER
1
In this package, you will find a keychain transmitter with 12V alkaline
battery, a wireless switch receiver and a clip.
Wireless Switch
Receiver
Keychain Transmitter
(Battery inside)
Clip
‘+’ ‘-’
‘0’
Note: A connector can be
removed with the clip,
as shown.
Remove the receiver from the electrical outlet before
changing the code.
WARNING
BATTERY
Connector 10 “Removed” TRANSMITTER
Button 2- Right button
Connector 10 set to “+” TRANSMITTER
Button 1- Left Button
5
6
7
RECEIVER
RECEIVER
Connectors
1 to 9 are
the same.
8Put the cover and screw back onto the receiver. Plug the receiver
into an electrical outlet.
Put the battery cover back onto the transmitter.
Clip
2
3
4
Remove the screw that holds
the connector cover, and pry
off the cover.
2. SET UP THE OPERATION CODE FOR BOTH
TRANSMITTER AND RECEIVER (CONT)
Plug the receiver into a powered, 120VAC electrical outlet inside
your house. (Note: This receiver is designed to be used indoor
only. Do not use this receiver in an outdoor environment.)
Once the receiver is plugged into an elec-
trical outlet, the red LED on the front of the
unit will be “on” indicating the unit is in
standby mode.
Plug in the light fixture or small appliance
that you would like to control into the
receiver, as shown.
If there is a power switch on the plugged
in light fixture or small appliance, please
turn it on. The receiver is ready to be
activated.
Pressing the appropriate button will
turn on the plugged in device and the
red LED on the front will flash.
(Caution: When the red LED on the
unit is flashing, that means output
outlet is powered. Do not disconnect /
connect devices from / to the receiver’s
outlet when the red LED is flashing.)
1
2
3
4
5
9
3. INSTALLATION

5. BATTERY
4. OPERATION
To activate the receiver, simply press the appropriate button on the
transmitter, it will activate the plugged in device. Pressing it again will turn
off the plugged in device.
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
10. WARRANTY
There are 2 buttons on your transmitter, the other
button can be used to control another Skylink®Garage
Door Receiver Model 318R (sold separately) or Skylink®
Wireless Switch Receiver Model SW-318R (sold
separately).
6. ADDITIONAL RECEIVER
You can add as many additional transmitters as you want
to control the same receiver. Simply set the same
operation code on all transmitters with the same code setting
on the receiver. Skylink®offers Keychain Transmitter
Model 318TN to work with your receiver. For more
information, please visit our website at
www.skylinkhome.com or contact us.
7. ADDITIONAL TRANSMITTER
11. CUSTOMER SERVICE
8. CAUTION
9. FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However,thereisnoguaranteethatinterference will not occur in a particular installation. If this equipment does
causeharmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : NOT FOR USE WITH DIMMER.
DISCONNECT POWER BEFORE CODE SETTING.
REPLACE COVER AFTER CODE CHANGING.
Maximum Rating :
Input : 120VAC 60Hz
Resistive : 8A (960W)
Incandescent : 300 watts
Motor Load : 1/3 HP
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:[email protected]
http://www.skylinkhome.com
P/N. 101A208-003 Rev.3
US Patent. D380895
©2005 SKYLINK GROUP
If you would like to order Skylink’s products or have difficulty getting them to work,
please :
1. visit our FAQ section at www.skylinkhome.com , or
2. email us at [email protected], or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm
EST. Fax [phone]
12 volt alkaline battery (size 23A)
(included).
It is time to change the battery
when the red LED on the
transmitter does not turn on when
either button is pressed.