SkyLink HU-318 User manual

skylinkhome.com
User’s Manual
HU-318

2
CONTENTS
INTRODUCTION .........................................................................3
SETTING UP THE INTERNET HUB ...........................................4
PROGRAMMING THE INTERNET HUB .................................... 5-25
Assign Zones and Lights ..............................................................................7-11
All On/Off ......................................................................................................12
Device .......................................................................................................... 13
Scene ........................................................................................................... 14-15
Timer ............................................................................................................ 16-17
TC Remote ...................................................................................................18-20
Camera ........................................................................................................ 21-23
Settings ........................................................................................................ 24-26
APPENDIX ..................................................................................27-29
Resetting the Internet Hub ........................................................................... 27
Advanced Installation ................................................................................... 28-30
FCC / IC ...................................................................................... 31
WARRANTY ................................................................................32
CUSTOMER SERVICE ............................................................... 32
CONTENTS

3
SkylinkHome™ Internet Hub allows you to remotely control various devices from a
computer, a Smartphone or tablet.
With the wireless camera, you may visually see your command occur, turning on a
light or opening a door.
The following items are included in this package:
 •OneInternetHub
 •OnePoweradapter
 •OneNetworkcable
 •User’sManual
 •SetupGuide
INTRODUCTION
INTRODUCTION
}CD

4SETTING UP THE INTERNET HUB
SETTING UP THE INTERNET HUB
Before installing the Internet Hub, ensure your system/network meets the following
requirements. You must have:
 •AnEthernetRJ-45portfromyourexistingWirelessrouter.
 •AcomputerinstalledwithanInternetBrowser.
Follow the steps below to setup your Internet Hub. Make sure you follow each step
carefully to ensure that the Internet Hub operates correctly.
1) Insert 4 AAA batteries into the Internet Hub
(with the correct polarity as shown). The LCD display will turn on and the
 PowerLEDwillash.
2) Using the network cable (provided) connect the Internet Hub to
your Wireless router.
3) Insert the DC adapter into the Internet Hub and then plug into an AC outlet.
 ThePowerLEDwillstayonsteadily.
Insert DC Adapter and BatteriesDCJackEthernetPort

5
TheInternetHubincludesawebgraphicsuserinterface(webGUI)whichallowsyou
toconguretheInternetHubusingyour
web browser on your computer.
After you have connected the Internet
Hub to your Wireless router and have
applied power to the Internet Hub, write
downtheIPaddressshownontheLCD
display of the Internet Hub, such as
192.168.001.199:8081. Yours may be
different from this.
LaunchyourwebbrowsersuchasInternetExplorer,GoogleChromeorFirefoxto
logintotheInternetHub.KeyintheIPshownontheLCDdisplayofyourInternet
Hub, e.g. http://192.168.001.199:8081. Or you may type in the default address
http://hu:8081.
Default User name : admin
 DefaultPassword:admin
You will then see this screen:
PROGRAMMING THE INTERNET HUB
PROGRAMMING THE INTERNET HUB

6
PROGRAMMING THE INTERNET HUB
PROGRAMMING THE INTERNET HUB
Bydefault,theInternetHubissettoDHCPClient,whichautomaticallyobtains
IPaddressesfromyourrouter.However,insomeinstancesyoumaywanttoassign
staticIPaddressestotheInternetHubtoensureconvenientaccessibility.
ToassignstaticIP,Goto[Settings]andthen[NetworkSettings].
 1.The[DDNSStatus]shouldshow“Ok”.WritedowntheDDNSname:
 “nh007.my.skyhm.net”inthisexample(yourswillbedifferent)
 andHttpPort:“8081”inthisexample.
 2.Uncheckthe[DHCPclient]todisabletheDHCPClientfunction.
 3.Click[SaveCong]tosavethecurrentsetting.

7
PROGRAMMING THE INTERNET HUB
ASSIGN ZONES AND LIGHTS
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB
To setup the Internet Hub to control SkylinkHome™ Wireless Modules, follow the
steps below:
1. Assign different zones such as Kitchen, Bedroom, Family Room, Hallway etc.
2. Assign different devices in each zone, such as island lights, ceiling lights,
 potlights,oorlampetc.
3. Learn the assigned light to the Wireless Module
Assign Zones and Lights
 1.ClicktheZoneiconor[Zone]inthetoolbar.
 2.Clickthe[Settings]icontochangethenameofthezone.
 3.Enterthezonename,(e.g.Kitchen),thenclick[ADD].
Repeat this step for all the zones that you plan to assign.

8
 4.Click[Zone]onthetopofthetoolbar.Selectthezone,
 e.g.[Kitchen]toassigndifferentdevicestothiszone.
 5.Clickthe[Settings]iconinthe‘KitchenDevicesControlPage’,
and then assign different devices in this zone.
 6.Enterthenameofthedevice(e.g.IslandLights).Selectthetypeofmodule
 controlled(On/OfforToggle,DimorNon-Dim)andthenclick[ADD].
PROGRAMMING THE INTERNET HUB
ASSIGN ZONES AND LIGHTS
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB

9
PROGRAMMING THE INTERNET HUB
ASSIGN ZONES AND LIGHTS
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB
7. After you have assigned a name for each light or device, you may now learn
the light to the Wireless Module. Refer to the User’s Instructions of that
 specicreceivertoputtheunitinto‘Learning’mode,thenpressthe[Learn]
 buttonontheInternetHubinterface.TheSignalLEDwillash,then
 turnoffontheInternetHubindicatingthe‘Learn’codehasbeensent.
8. This light is now programmed to the Wireless Module.
Repeat the same instructions to program the rest of the lights.
 9.Tooperatethelights,gotothe‘ZoneControlPage’.
 Forexample,select[Kitchen]andchoosethelightyouwanttocontrol.

10
 10.Eachlighthas4controlbuttons:On/Off/Bright/Dim
•Pressthe[ON]buttontoturnonthatlight.
 •Pressthe[OFF]buttontoturnoffthatlight.
 •Pressthe[Bright]buttontoincreasethebrightnessofthatlight.
 •Pressthe[Dim]buttontodecreasethebrightnessofthatlight.
Note:Tochangethebrightness,makesuretheWirelessModuleandtheload
(i.e. the light bulb) are dimmable.
11. You can setup a camera to view live images of this zone.
 Pleaserefertothe‘Settings page’ to setup a wireless camera.
PROGRAMMING THE INTERNET HUB
ASSIGN ZONES AND LIGHTS
ASSIGN ZONES AND LIGHTS PROGRAMMING THE INTERNET HUB
 12.Toprogramthezonecontrol,gototheZonepageandclick[Settings].
You will see the following screen. For instance, in the Kitchen zone,
there are 4 lights. First put the Island Light Module into learning mode,
 thenpressthe[Learn]buttononthisscreen.NextputtheSpotLightmodule
 intolearningmode,thenpressthesame[Learn]buttononthisscreenagain.
 Repeatthisstepforallthemodulesinthe[Kitchen]zone.