Skytech 1315G User manual

This remote control system offers the user a 110-120 VAC powered multi-purpose remote control to be used with AC
powered products such as lamps, heaters, fans, electric replaces, lighting and pump motors used for decorative ponds/
waterfalls from up to 30 feet away.
MODEL: 1315G
INSTALLATION AND OPERATING INSTRUCTIONS
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS
DO NOT ATTEMPT TO INSTALL OR OPERATE
INTRODUCTION
OFF
ON
On the back of all transmitters are code switches with pre-set codes from
the factory. The transmitter will operate with the receiver as is without
setting new codes. However if you are installing more than one 1315G
in a home a different code must be set to prevent interference another
transmitter. There are 255 set able security codes. Simply use a small
screwdriver to change the codes.
Skytech: 1315G REV 11-8-16 Page 1
The transmitter has ON and OFF functions that are activated by
pressing either button on the face of the transmitter. When a button on
the transmitter is pressed, a signal light on the transmitter
illuminates briey to verify that a signal has been sent. The
transmitter also has (2) code switches located on the back that will need
to be set before installation. Note: See Code Setting section.
The receiver plugs directly into a polarized 110-120 VAC grounded
receptacle. Then an AC powered appliance is plugged directly into the
receiver which is controlled by the transmitter (remote control). In
addition the receiver has an indicator light verifying power to the
receiver.
If an extension cord is required, only use a (Model 18SPT-3) cord
consisting with an appropriate temperature rating for the intended use.
Both ends of the extension cord must be grounded and
polarized. An extension cord can be purchased from your appliance
dealer.
Receiver
Transmitter
CODE SETTING
AC
E
G
I
K
M
O
1
3
5
7
9
11
13
15
AC
E
G
I
K
M
O
1
3
5
7
9
11
13
15
MODEL NO:
Back of Transmitter
If you change codes, write code and room location below and keep for
future use.
Code ___________ ______________ Room
+
CR2032
BATTERY
SLIDE BOTTOM TAB
DOWN TO EXPOSE
BATTERY
BATTERY INSTALLATION
The transmitter operates on (1) 3-volt button cell lithium battery (included). Remove the
battery holder down by sliding the tab at the bottom of the transmitter down and out.
Install the battery with the + side up. Then slide the battery holder back into the
transmitter. See drawing at the right.
Battery Compartment

INSTALLATION
OFF
ON
Reciever Transmitter
Power Source
Electrical Appliance
Installation is simple. Plug the receiver into a polarized 120 VAC grounded
receptacle/outlet. Plug your AC powered electrical appliance into the receptacle of the
receiver and turn the appliance switch ON. At the bottom of the receiver directly
above the indicator light is a recessed “learn” button. Use a toothpick, or pencil tip to
press the button in and release. Next press any button on the
transmitter and the receiver will “click” two times to conrm operation.
Once your AC electrical appliance is connected to the receiver, the remote is ready
to operate. To turn ON the appliance, press the ON button on the transmitter. To turn
OFF the appliance, press the OFF button on the transmitter.
Recessed Button
Press & Release Learn Button
Basic Installation
TROUBLESHOOTING
If you encounter problems with your 1315G, the problem may be with the electrical appliance itself, the remote or the
receiver. Review the electrical appliance manufacturer’s operation manual to make sure all connections are properly
made. Then check the operation of the remote in the following manner:
• Ensure the electrical appliance switch plugged into the receiver is turned ON.
• Make sure the the RECEIVER has power. Try another appliance you know that works or test with receiver
receptacle with a volt meter.
• Check the battery in the Transmitter to ensure it is installed with the (+) side up and has at least 3VDC.
• Check the code settings on the transmitter and ensure they were not change. If unsure of code setting then
re-learn the transmitter to the receiver by following the installation instructions above.
• Be sure RECEIVER and Transmitter are within 30-foot operating range.
• Keep RECEIVER from temperatures exceeding 130º F.
• If RECEIVER is installed in tightly enclosed metal surroundings, the operating distance will be shortened.
SPECIFICATIONS
BATTERIES: Transmitter 3V button cell (CR2032) FCC ID No.’s: transmitter – K9L 4001THTX
Operating Frequency: 433.92MHz Canadian ISC ID No.’s: transmitter –2439A 4001THTX
FOR INDOOR USE ONLY
Load Ratings: Resistive 15A (1800W), Motor 1/3HP, Tungsten Lamp 600W
Input: 120VAC/ 60Hz
Skytech: 1315G REV 11-8-16 Page 2
FCC REQUIREMENTS
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE
EQUIPMENT.
Skytech Products Group
9230 Conservation Way
Fort Wayne, IN 446809
888-672-8929
www.skytechpg.com
(APPLIANCE CONTROL)
44V2