DELTA DORE TYXIA 1705 User manual

TYXIA 1705

EN
1514
1/ Location/Mounting 14
1.1 Mounted on the wall 14
1.2 Placed on a at surface 15
2/ Wireless association 16
2.1 Associating a motor or receiver 16
3/ Save the favourite positions 19
4/ Use 20
5/ Troubleshooting 21
ContentsTechnical characteristics
• Power supplied by 3V lithium battery, CR2430
• Class III insulation
• X3D Transmission frequency:
868.7 MHz to 869.2 MHz
• Maximum radio power < 10 mW
• Receiver category II
• Wireless range: 100 to 300 metres outside,
variable depending on the associated equipment
(the range can vary depending on the installation
conditions and the electromagnetic environment)
• Mounted on a base
• Dimensions: 46 x 121 x 10.7 mm
• Degree of protection: IP 40
• Operating temperature: 0 to +55°C
• Storage temperature: -10 to +70°C
• Installation in an environment with normal
pollution levels

EN
1716
1.2 Placed on a flat surface
1/ Location/Mounting
1.1 Mounted on the wall

EN
1918
> 3s
2/ Wireless association
This chapter allows you to associate a remote
control with an X3D wireless motor or X3D roller
shutter receiver.
2.1 Associating a motor or receiver
2.1.1 A single motor is turned on
❶Set the motor or receiver to association standby
mode.
❷On the remote control press and at the
same time and hold for 3 seconds, until the LED
ashes. Release.
❸ The shutter is activated briey to conrm the
association.
To exit association mode, press for 3 seconds.
❶ Activating association standby mode
- Motor:
1) Upon turning on for the rst time, if the motor
was not associated before.
2) From a remote control used for the motor
(already associated) press the button for 3
seconds.
- Receiver: press its button for 3 seconds until the
LED ashes.

EN
2120
2/ Wireless association
2.1.2 Several motors or receivers are in association
standby mode
❶On the remote control press and at the
same time and hold for 3 seconds, until the red
LED ashes. Release.
The remote control searches the different motors or
receivers.
Its LED ashes, alternating red/green.
❷ When the LED starts ashing red slowly, press
the button as many times as required to select
the motor (receiver) to associate.
The corresponding shutter activates briey.
❸Once the motor (receiver) has been found, press
.
❹ The shutter is activated briey to conrm the
association.
To exit association mode, press for 3 seconds.
2.2 Associate multiple motors or receivers
❶Set the motors (receivers) to association standby
mode.
❷On the remote control press and at the
same time and hold for 3 seconds, until the LED
ashes. Release.
The remote control searches the different motors or
receivers. Its LED ashes, alternating red/green.
❸ When the LED starts ashing red slowly, press
and at the same time and hold for 3
seconds until the red LED turns on.
❹ The shutters are activated briey to conrm the
association.
To exit association mode, press for 3 seconds.

EN
2322
> 3s
3/ Save the favourite positions
You can save up to 2 favourite positions: and
.
❶❷ Set the shutter to the required position e.g.
).
❸Press or to set the angle of the slats.
❹Press + or + and hold for 3
seconds to save the position.
The shutter is activated briey.
Release.
4/ Use
• Press , or to control the roller shutter.
The green LED indicates that the receiver has
correctly received the information.
• Press or to set the angle of the slats.
• Press to go to favourite
position 1 (if it has been saved).
• Press to go to favourite
position 2 (if it has been saved).

EN
2524
CR 2430
5/ Troubleshooting
• The red LED ashes
several times every time
a button is pressed.
The battery is low.
Change the battery.
• Remove an association
- Remove the front face of
the remote control.
- Press button A.
The red LED ashes.
- Press as many times as
required to select the motor
(receiver) to remove.
- Press the button.
- Press button A to exit.
• Remove all associations
- Remove the front face of the remote control.
- Press button A.
The red LED ashes.
- Press the and buttons at the same time and
hold for 3 seconds.
- Press button A to exit.

www.deltadore.com