SKYTRONIC 171.325 User manual

1
2-Channel UHF Wireless
Microphone System
Model Nos:
171.325 863.3 + 864.3MHz
171.326 863.8 + 864.8MHz

2
Operation Manual
POW ER
VOLUME
CHANNEL A
RF AF LEVEL
VOLUME
CHANNEL B
RF AF LEVEL
PROFESSIONAL 2-CHANNEL WIRELESS SYSTEM
ANT.A ANT.B
2-Channel Receiver
Handheld transmitter Antenna
AC adaptor Audio cable

3
PRECAUTIONS
• Avoid exposure of the system to rain or moisture.
• No user-serviceable parts inside the system. Refer all servicing to a qualified technician only.
• Handle the wireless system carefully, dropping or other shocks may cause failure.
• Avoid using the system where it may be subjected to heat, such as direct sunlight, near radiators or
other heat sources.
• Should any liquid be spilt on the system, stop using it immediately. It may be possible to dry the
system, but you should have it checked by a qualified technician before using it again.
• Take care with the main power adapter and lead. If damaged in any way, do not use the system and
refer to a qualified technician for repair.
• Only use the system with the supplied components. Do not attempt to use with any other main power
supply adapter .
• If the is not going to be used for a while, remove the battery to prevent leakage. In the event of
electrolyte leakage inside the battery compartment, carefully remove the leakage with a damp cloth.
Take care not to get battery electrolyte in contact with your skin, however if it does, wash your hands
under a running tap. If electrolyte comes into contact with your eyes, seek medical advice immediately.
• Only replace the battery with the same or an equivalent type.
• Please dispose of old batteries in an environmentally friendly manner in accordance with the relevant
legislation.
• Do not use any solvents to clean any part of the wireless system.
2-CHANNEL UHF WIRELESS
MICROPHONE SYSTEM
Thank you for buying this Skytronic UHF Wireless System. Please read through these
operation instructions so you will know how to operate your model properly. After you read it,
put it away in a safe place for future reference.
Model Nos:
171.325 863.3 + 864.3MHz
171.326 863.8 + 864.8MHz

4
Operation
Unscrew the battery cover at the end of microphone, put a 9V battery into compartment observing
correct polarity, then close the cover.
Move "ON/OFF" switch to "ON" position, "PWR" indic ator will light for one second and then go off. This
indicates correct operation. If it doesn't come on, please check the voltage of battery or polarity. If the
"PWR" indicator lights red, this indicates the battery power is low. Please replace with a fresh battery.
WIRELESS MICROPHONE
SPECIFICATIONS
A.Overall system
Oscillation mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Quartz controlled
Carrier Frequency Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UHF690-960MHz
Stability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Max Deviation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56KHz with level limiting
Dynamic Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >110dB
S/N Ratio: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >100dB
T.H.D: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<0.5dB
Squelch: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ."Pilotone & Noise lock" dual squelch circuit
Frequency Response: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Hz~18KHz
B. Receiver
Sensitivity: 6dB V at S/N>70dB
Image Rejction: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >60dB
Stability: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >80dB
Audio output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -12db/600ohms unbalanced and balanced
Power supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC/0.5A
Dimensions (mm):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 x 208 x 45mm
C. Transmitter
Mic capsule: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Dynamic microphone (Handheld mic)
Antenna: . . . . . . . . . . . . . . . . . . . .Built-in housing (Handheld transmitter) External (Belt pack transmitter)
RF Output: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <10mW
Spurious: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <-40dB
Battery:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 x 9V (6F22, PP3)
POWER
INDICATOR
BATTERY COVER
POWER SWITCH
UNSCREW BATTERY
COVER TO INSERT
BATTERY

5
POWER
1
2
33
410
10
VO LUME
CH AN NEL A
RF AF LEVEL
VO LUME
CH AN NEL B
RF AF LEVEL
7
56 8 9
ANT.A ANT.B
PROFESSIONAL 2-CHANNEL WIRELESS SYSTEM
XLR MIXED MIXED CH-A SQB SQA
DC IN
12V/500mA
11 12 13 14 15
RECEIVER FRONT PANEL
Operation
Fix the two antennas correctly. Switch on the power of receiver, the red indicator of power will come on
to show it's working normally. Switch on the power of transmitter, the red indicator RF/channelA, RF/
channelB, will come on to show the signal is strong or not when it's working. AF LEVEL green indicators
are blinking to show the audio level is high or low in using this wireless microphone system. Adjust
the volume of the receiver/transmitter/amplifier according to request. Please switch off the receiver/
transmitter/amplifier when this wireless microphone system is not being used.
RECEIVER REAR PANEL
SQUELCH
The squelch control on the rear of the receiver is preset well at the factory, if you must use the system
in an area with considerable RF interference and there is some noises from the receiver when your
transmitter is off, you can adjust the squelch control, so the system will receive the signal from your
transmitter only but squelch or eliminate the unwanted background RF noise. This adjustment can cause
reduction in useable range of the wireless transmitter, so set the control to the lowest position that
reliablely mutes the unwanted RF signals.
Note that switching the microphone on and off can cause interference that will be heard if the
microphone volume level of the amplifier system is still set high.
11. Balanced mixed output jack
12. Unbalanced mixed output jack
13. CH-A unbalanced output jack
14.Squelch adjuster
15. DC power in
1. Power Light
2. Power Switch
3. Antenna
4. CH-A Volume Control
5. CH-A RF Signal Light
6. CH-A AF Level
7. CH-B Volume Control
8. CH-B RF Signal Light
9. CH-B AF Level
10. Rack Mounting

6
Professionalmixer
MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE
XLR MIXED MIXED CH-A SQB SQA
DC IN
12V/500mA
SYSTEM INSTALLATION
Using the supplied screened jack-to-jack lead, connect from the MIXED jack socket to the "MIC IN"
socket on amplifier. Another way, using optional lead of balanced output, connect from "XLR MIXED"
socket on receiver to professional mixer. Plug the mains power adaptor from "DC 12V" jack to a suitable
mains power socket.
IMPORTANT
Install main unit 1.5m higher than ground level and1.5m distance from wall

7
The on air
indicator does
not light up
No sound
The sound is
distorted
A howling noise
heard from the
speakers.
The wireless microphone is not turned on.
The microphone receiver is not turned on.
The microphone receiver is not connected
properly.
The battery in the wireless microphone is
weak.
The microphone receiver is not turned on.
The connected audio equipment is not
turned on.
The speakers/headphones. are not
connected to the audio equipment.
The battery in the wireless microphone is
weak.
The AUDIO OUT on the receiver is not set
correctly.
The distance between the wireless
microphone and speakers are too close.
The battery in the wireless microphone
is weak
Turn on the wireless microphone
Turn on the microphone receiver
and the connected audio equipment
Turn on the microphone receiver
and the connected audio equipment.
Replace the battery
Turn on the microphone receiver
and the connected audio equipment.
Turn on the audio equipment.
Connect the speakers/headphones
Replace the battery.
Adjust the volume cotrols.
Move the wireless microphone away
from the speakers or change the
direction of the microphone.
Replace the battery.
TROUBLE SHOOTING

8
Handleiding
POW ER
VOLUME
CHANNEL A
RF AF LEVEL
VOLUME
CHANNEL B
RF AF LEVEL
PROFESSIONAL 2-CHANNEL WIRELESS SYSTEM
ANT.A ANT.B
Twee kanaals ontvanger
Staafmicrofoon Antenne
(Zender)
AC Adapter Audiokabel

9
VOORZORGSMAATREGELEN
• Bewaar de verpakking zodat u indien het apparaat defect is, dit in de originele verpakking kunt
opsturen om beschadigingen te voorkomen.
• Voordat het apparaat in werking wordt gesteld, altijd eerst een deskundige raadplegen indien u niet op
de hoogte bent met audio apparatuur.
• In het apparaat bevinden zich onder spanning staande onderdelen; open daarom NOOIT dit apparaat
• Verwijder of plaats een stekker/adaper nooit met natte handen resp. uit en in het stopcontact.
• Indien het apparaat zo beschadigd is dat inwendige (onder)delen zichtbaar zijn mag de adapter NOOIT
in het stopcontact worden geplaatst én het apparaat NOOIT worden ingeschakeld. Neem in dit geval
contact op met de dealer.
• Reparatie aan het apparaat dient te geschieden door resp. een vakman of een deskundige.
• Sluit het apparaat alléén aan op een 230VAC / 50Hz (geaard)stopcontact, verbonden met een 10-16A
meterkastgroep.
• Toestel niet opstellen in de buurt van warmte bronnen zoals radiatoren etc. en niet op een vibrerende
ondergrond plaatsen. Tevens dient u gebruik in een vochtige omgeving te vermijden.
• Bij onweer altijd de adapter uit het stopcontact halen, zo ook wanneer het apparaat voor een langere
tijd niet gebruikt wordt.
• Als u het apparaat lang niet gebruikt heeft en het weer wil gebruiken kan er condens ontstaan; laat het
apparaat eerst op kamertemperatuur komen alvorens het weer in werking te stellen.
• Apparaat nooit in vochtige ruimten en buiten gebruiken.
• Om ongevallen in bedrijven te voorkomen moét rekening worden gehouden met de daarvoor geldende
richtlijnen en moeten de aanwijzingen/waarschuwingen worden opgevolgd.
• Het apparaat buiten bereik van kinderen houden.
• Gebruik geen schoonmaakspray om de regelaars te reinigen. Restanten van deze spray zorgen ervoor
dat smeer en stof ophopen in de regelaars. Raadpleeg bij storing te allen tijde een deskundige.
• Zorg dat uw handen schoon zijn tijdens het gebruik.
• Gebruik geen overmatige kracht bij het bedienen van de schakelaars en knoppen.
• Tracht het apparaat niet schoon te maken met chemische oplossingen. Dit kan de lak beschadigen.
Gebruik een droge doek om schoon te maken. Laat vocht /vloeistof niet in het systeem binnendringen
ivm kortsluiting.
2-KANAALS UHF DRAADLOOS
MICROFOON SYSTEEM
Hartelijk dank voor de aanschaf van ons Skytronic Draadloos Microfoon Systeem.
Lees, alvorens dit artikel te gebruiken, de handleiding door en bewaar deze
handleiding als naslagwerk.
Model:
171.325 863.3 + 864.3MHz
171.326 863.8 + 864.8MHz

10
• Blijf uit de buurt van electronische apparatuur die bromstoringen zouden kunnen veroorzaken.
• Bij reparatie dienen altijd originele onderdelen te worden gebruikt om onherstelbare beschadigingen
en/of ontoelaatbare straling te voorkomen.
• Schakel eerst het toestel uit voordat u de adapter en/of aansluitsnoeren verwijdert.
• Deze instructiemarkering wordt weergegeven om u erop te wijzen dat de instructie zeer
belangrijk is om te lezen en/of op te volgen.
• Er mogen géén veranderingen/modificaties worden doorgevoerd ; deze kunnen de CE status te niet
doen met alle gevolgen vandien. Tevens vervalt de garantie!
• Indien het systeem niet gebruikt wordt verwijder dan de batterij; defecte/lege batterijen inleveren als
k.c.a.
SPECIFICATIES
A.Algemeen
Oscillatior mode: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Quartz controlled
Werkfrequentie: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 863 - 865 MHz
Stabiliteit: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005%
Max Deviatie: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56KHz with level limiting
Dynamic Range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >110dB
Signaal/ruis: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >100dB
T.H.D: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .<0.5dB
Squelch: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ."Pilotone & Noise lock" dual squelch circuit
Frequentie bereik:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60Hz~18KHz
B. Ontvanger
Gevoeligheid: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6dB V at S/N>70dB
Image Rejction: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >60dB
Stabiliteit: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >80dB
Audio uitgang: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -12db/600ohms unbalanced and balanced
Voeding adapter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12VDC/0.5A
Afmeting (mm): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 x 208 x 45mm
C. Zender
Mic capsule: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dynamic microphone (Handheld mic)
Antenne mic: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ingebouwd (Hand microfoon)
Extern (Body Pack)
RF Vermogen:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <10mW
Spurious: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <-40dB
Batterij: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 9V (6F22, PP3)
Afmetingen: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240 x 49mm

11
Bediening
Draai het batterijvak open en plaats een 9V batterij ; controleer de polariteit .
Wanneer de Power schakelaar op ON wordt gezet brandt de Power led één seconde en gaat dan uit. Als
de Led niet aangaat controleer dan de polariteit van de batterij. Wanneer de Led “rood” blijft branden is
de batterij bijna leeg. Vervang de batterij en lever de lege batterij in als chemisch afval .
DRAADLOZE MICROFOON
DRAAI HET BATTERIJVAK
OPEN EN PLAATS
BATTERIJ
POWER LED POWER SCHAKELAAR BATTERIJVAK
POWER
1
2
33
410
10
VO LUME
CH AN NEL A
RF AF LEVEL
VO LUME
CH AN NEL B
RF AF LEVEL
7
56 8 9
ANT.A ANT.B
PROFESSIONAL 2-CHANNEL WIRELESS SYSTEM
ONTVANGER VOORZIJDE
Bediening
Plaats de twee antennes ; bij het aanzetten van de ontvanger zal de Powerled gaan branden. Wanneer
de microfoons worden ingeschakeld zal de rode led van RF-Kanaal A-B gaan branden. De AF-signaal
indicatie (groen) van Kanaal A-B gaat knipperen naar gelang de sterkte van het audiosignaal. Deze kan
worden afgeregeld met de volumeregelaar van Kanaal A-B. Schakel het systeem uit indien er geen
gebruik meer van wordt gemaakt.
1. Power Led
2. Netschakelaar
3. Antenne
4. Kanaal A volumeregelaar
5. Kanaal A RF-signaal indicatie
6. Kanaal A AF-signaal indicati
7. Kanaal B volumeregelaar
8. Kanaal B RF-signaal indicatie
9. Kanaal B AF signaal indicatie
10. Rack montageklemmen

12
XLR MIXED MIXED CH-A SQB SQA
DC IN
12V/500mA
11 12 13 14 15
ONTVANGER ACHTERZIJDE
Squelch
De squelch is door de fabrikant standaard ingesteld ; indien in een omgeving hoogfrequent interferentie
voorkomt en vanuit de versterker een storing/ruis klinkt als de microfoon is uitgeschakeld kan m.b.v. de
squelchregelaar het systeem zo worden ingeregeld dat alleen het signaal afkomstig van de microfoon is
te horen.
Bij het in-en uitschakelen van de microfoon kan een plop/storing worden gehoord als het volume van de
ontvanger te hard staat.
11. Gebalanceerde uitgang gemixt
12. Ongebalanceerde uitgang gemixt
13. Ongebalanceerde uitgang Kan. A
14. Squelch regelaar
15. 12V Ingang
Professionalmixer
MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE
XLR MIXED MIXED CH-A SQB SQA
DC IN
12V/500mA
INSTALLATIE
Installeer het draadloze microfoon systeem zoals hiervoor is weergegeven, sluit de ongebalanceerde-
uitgang (12) van de ontvanger aan op de microfoon-ingang van een versterker. Indien gebruik gemaakt
wordt van een mengpaneel kan XLR-uitgang 11 van de ontvanger aangesloten worden. Sluit het adapt-
ersnoer aan op de 12V-ingang van de ontvanger en steek de adapter in het stopcontact. Zorg er echter
wel voor dat regelaars zijn teruggeregeld alvorens de installatie aan te zetten.
NB: Zet de installatie op +/- 1.5 mtr hoogte en niet tegen een muur (+/- 1.5 mtr verwijderd)

13
De on-air
verlichting gaat
niet aan
Geen geluid
Geluid vervormt
Bulderend/
gierend geluid
uit de speakers
Microfoon staat niet aan
Ontvanger staat niet aan
Aansluitsnoeren maken slecht contact
Batterij is leeg
Ontvanger staat niet aan
De versterker / mengpaneel of andere
audio apparatuur staat niet
Luidsprekers / Hoofdtelefoon etc. zijn niet
goed aangesloten.
Batterij is bijna leeg
AF-out is niet goed ingesteld.
Microfoon is te dicht bij de speakers
gehouden.
Batterij is bijna leeg
Zet de microfoon aan
Schakel de ontvanger en de andere
audio apparatuur in
Controleer de installatie én
aansluitsnoeren.
Vervang de batterij
Schakel de ontvanger in
Schakel de andere audio apparatuur in
Controleer de aansluitingen
Vervang de batterij
Regel het volume beter in.
Verwijder de microfoon bij de speakers
Vervang de batterij
TROUBLE SHOOTING

14

15
CE Declaration of Conformity
Importer: SkyTronic BV
Marconistraat9
7442 DD Nijverdal
The Netherlands
Product number: 171.322-171.323-171.325-171.326
Product Description: UHF Wireless Microphone 863-865 MHz
Regulatory Requirement: EN 60065
EN 301 489-1 V1.6.1
EN 301 489-9 V1.3.1
EN 300 422-2 V1.1.1
To our opinion the product is deemed to meet the requirements of the above
mentioned Declaration(s).
This certificate does not cover the aspects that may be relevant such as
performance and fitness for purpose.
Nijverdal,
06-03-2008
Signature

16
www.skytronic.com
This manual suits for next models
1
Table of contents
Languages:
Other SKYTRONIC Microphone System manuals
Popular Microphone System manuals by other brands

Luxlink
Luxlink IRGT-1501 operating instructions

VTQ Videotronik
VTQ Videotronik Video 2000 Series quick start guide

Tekon
Tekon DUOS installation guide

Heyuan Intelligence
Heyuan Intelligence IOT-G2S-01 user manual

SWIT Electronics Co.,LTD.
SWIT Electronics Co.,LTD. CW-S150 user manual

Shure
Shure UHF-R Wireless user guide