SL Mini Max af User manual

SL Mini Max af

18 19
English
Warning!
Avoid looking directly into the light emitted by the light or shining the light into your own eyes or
the eyes of another person. If the light accidentally shines into your eyes, close your eyes and move
your head out of the light beam. Do not use any strongly focusing optical device to look at the light
beam.
In cases where the light is used in a public or commercial setting, users should be provided with trai-
ning concerning the safety measures for laser light.
This device may then be used by children 8 years of age or older, persons with limited physical,
sensory or mental capabilities, as well as persons with no previous experience in handling such
devices, if they are supervised by a person responsible for their safety.
Carry a spare light with you at all times, as the product can potentially fail unexpectedly at any
time.
Defects:
Light source must be replaced in general if the light source (or one of the LEDs) is defective.
In the event of any physical or internal battery failure, do not attempt to repair.
No user-servicable parts!
Heat generation:
The housing of SL may heat up; so make sure that you always keep the light at a safe distance to
any combustible or flammable materials. Could cause fire or death! However, quiescent operation
(without cooling the light housing via airflow or the like) is possible at any time and will not damage
the product. Always disconnect the battery from the light at transport or storage!
Water resistance:
All SL components are waterproof and can of course be used under extremely severe
conditions. The lamp complies with IP protection class 67 but is NOT a diving lamp and is
NOT suitable for use under water.
Cleaning:
Do not use a strong water jet or heavy detergent to clean the lamp.
Safety instructions

20 21
Assembly Instructions
Position the lamp centric at the handlebar. Now close the bracket of the quickrelease so the SL is moun-
ted tight in its position.
Important: The beam must be at least inclined so that its center is only half as high as 5 m away from
the headlamp. For this, it may be necessary to adjust the inclination of the mounts.
Height of the light cone after
5m: Half height as outlet
5m:
1/2
For proper setup screw on the lever of
the quick release mount.
The quick release can be mounted on both sides,
depending on the stem width.
English
Battery mounting
Battery mounting:
Your battery is supplied with a velcro strap, coated with an anti-slip material to ensure a secure mount.
Use the strap which most closely matches your tube size.
Battery type:
The battery is mounted with a velcro as shown here. They also come with a capacity indictaor.
When mounting the quick release, note the position of the O-rings. One O-ring should be between
the holder and the lamphead and the other one between the holder and the screw.

22 23
Turn on:
By connecting the battery to the lamphead it turns on automatically. The lamp can also be switched on by a short
press on the button of the lamp head. Depending on the ambient light, the SL starts lighting either with low beam
or daytime running light. Note: Only in the dark when the low beam is activated, it‘s possible to switch into high
beam.
Turn off:
To turn off the lamp, keep the button pressed for about 2 seconds.
Operation
Light mode:
A brightness sensor automatically switches between daytime running light and low beam.
Bluetooth remote control:
In order to save battery capacity, the remote connection between the lamp and remote control stays active for
only 1 hour when the lamp is switched off (standby) and the lamp can be switched on immediately at any time.
After that, the lamp may start with a delay, since the signal is only checked every 10 seconds (represented by
a blue blinking of the remote control). After 25 hours, the connection between the lamphead and the remote
control will be completely turned off. The lamphead can then only be activated again via the remote control
when the lamphead is reconnected to the battery or switched on using the underneath button of the lamphead.
Daylight
Small button:
- Switch to low beam
(Press again to deactivate,
sensor is not active)
Big button:
- Without function
English
Keep the button
pressed (let go to
select) until SL
lights up
Lights up 1x
Lights up 2x
Lights up 3x
Lights up 4x
Lights up 5x
Delay (5 sec / 16 sec.)
Factory setting: 16 sec.
Sensor calibration
Only in the assembled state!
Improper calibration may
greatly affect the functionality
of the light! Calibrate only
outdoors. No artificial light or
close to reflective objects!
Available settings
The sensor controlled switchover from night- to daytime
running light occurs as required in either 5 or 16 sec.
Saves the measured brightness value as a switching
point from daytime-to nighttime running light. The
successful sensor calibration is confirmed by a short
illumination of the daytime running light.
Explanation
Customizing the settings at the lamphead:
Reset to factory settings
ECO 1 High beam: 16W, Low beam: 8W, Daytime running light: 2W
Keep the small button pressed (let go to select) until the lamp lights up as many times you‘ll need it to.
Note: It will take about 6 sec. until the programming starts.
Note: The light outputs the maximum amount of light only if airflow lowers the temperature of the light
sufficiently. If the light is not cooled by airflow, its power is reduced incrementally to prevent the LEDs and
electronic elements from overheating.
Darkness / Night
Small button:
- With a short press: Low beam dims to 5W
(Not possible when ECO 2 is activated)
- Keep it pressed for about 2 sec.:
Activate daytime running light
(Press again to deactivate, sensor is not active)
Big button:
- If low beam is activated, switching to
high beam is possible.
ECO 2 High beam: 10W, Low beam: 5W, Daytime running light: 2W
Factory setting High beam: 25W, Low beam: 8W, Daytime running light: 2W

24 25
Operation Lamphead informations
Warning!
The lamp flashes several times. Stop immediately!
The light will be switched off.
1. Battery Warning, low capacity remaining.
High beam is activated.
Lamp lights up 1x:
Lamp lights up several times:
At the remote:
The „high beam symbol“ of
the remote lights blue
Battery warning at the lamphead in operation:
English
Capacity indicator
Audible:
To check the capacity, simply press the touch-pad once. At first an audible signal will
sound to give a quick reading in 20% steps.
Visible:
The visible indicator uses 5 LEDs. The LEDs can operate in two different operating
states: blinking and continuous. LED meanings:
A blinking LED is indicating a 10% step and a continuously glowing LED a 20% step.
Taillight:
To run the taillight simply press the touch pad two times and the 5 LEDs will operate continuously.
To switch off the taillight, simply press the pad again.
Moving light:
Press the touch pad three times to activate the moving light. To switch it off
press the button another time.
Operation Smartcore battery
5 x = 100 %
4 x = 80 %
3 x = 60 %
2 x = 40 %
1 x = 20 %
Example: 3 LEDs steady glow (20 %, 40 %, 60 %)
1 LED blinking (80 %) = 70 % remaining capacity