Slackline-Tools Vario-Slack WALL User manual

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 5
ASSEMBLY INSTRUCTIONS
I. Vario-Slack WALL – wall anchoring for slacklines
The Vario-Slack WALL wall anchoring is part of the Vario-Slack
set WW ( g. 1) and the Vario-Slack set GW ( g. 2) and is used
for  rmly mounting the slackline to an even concrete wall.
The resistance to fracture on even concrete ground
is 2200 daN.
Only use the supplied Fischer dowels (bolt anchor FAZ II
12/120) or similar dowels of a different manufacturer with
a clamping depth of at least 110 mm.
The wall anchoring Vario-Slack WALL may only be used
for slacklining in combination with the Slackline-Tools
products Slack-Grip, Slack-Ratchet CL 30 and the CLASSIC
Slackline-Tools band.
We recommend having the Vario-Slack WALL mounted by
a specialist.
Scope of delivery for the assembly of the Vario-Slack WALL
wall anchoring for each side:
•1 x Vario-Slack WALL
• 6 x FAZ II 12/120 including washer and M12 nut
• 6 x plastic cap
• 2 x mounting block
•1 x assembly instructions
Fig.1: Vario-Slack set WW
Fig. 2: Vario-Slack set GW
Mounting blocks
FAZ II 12/120 anchor
Washer
Plastic cap
M12 nut
Fig. 3: Fig. 4:
Recommended mounting
height 250 mm above
the ground
250 mm
650 mm
600 mm
300 mm 300 mm
300 mm 300 mm
Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 5 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 6
The Vario-Slack GROUND ground anchoring is part of the
Vario-Slack set GG and the Vario-Slack set GW and is used for
rmly mounting the slackline to an even concrete oor.
Only use the supplied Fischer female thread anchors RG M12I
and an appropriate injection mortar (e.g. Fischer FIS EM or
similar products of a different manufacturer; not included in
the scope of supply).
The ground anchoring Vario-Slack GROUND may only be used
for slacklining in combination with the Slackline-Tools products
Slack-Grip, Slack-Ratchet CL 30 and the CLASSIC Slackline-Tools
band.
We recommend having the Vario-Slack GROUND mounted by
a specialist.
Scope of delivery for the assembly of the Vario-Slack GROUND
ground anchoring:
•1 x oor rack
•1 x Vario-Slack WALL
• 6 x M12x160 hexagon head screw
• 6 x M12 hexagon nut
• 6 x washer, small
• 6 x washer, large
• 12 x plastic cap
• 2 x M12 RG 18 x 125 female thread anchor
• 2 x M12x60 knurled screw
•1 x assembly instructions
Fig. 5: Vario-Slack set GG
Fig. 6: Vario-Slack set GW
II. Vario-Slack GROUND – wall anchoring for slacklines
Requirements for assembly
• Level concrete surface, cracked or non-cracked, concrete
compressive strength class C 20/25 to C 50/60.
• Concrete thickness of at least 200 mm.
• Space requirements: 740 mm wide and 400 mm high.
• Recommended mounting height above ground: 250 mm.
• Recommended mounting distance between two
Vario-Slack WALL wall anchors: 4–6 m, max. 10 m.
• Make sure that both Vario-Slack WALLs are aligned
opposite to each other. The slackline must not be
pull diagonally!
Assembly
Position the Vario-Slack WALL according to the above
drawing (g. 3) using the mounting blocks, and handle
the wall anchors (weight: 14 kg) with care.
• Mark the six boreholes on the wall or drill the boreholes
immediately through the Vario-Slack WALL without
marking.
• Drill a borehole with a diameter of 12 mm and a depth
of at least 150 mm.
• Clean the boreholes.
• Position the Vario-Slack WALL with the FAZ II 12/120
anchors plus washers on the wall.
• Tighten the nuts (wrench size: 19) with a tightening
torque of 60 Nm.
•Apply the supplied plastic caps to the nuts.
• Remove the mounting blocks.
Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 6 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 7
Requirements for assembly
• Level concrete surface, non-cracked, of concrete
compressive strength class C 20/25 to C 50/60.
• Concrete thickness of at least 150 mm.
• Space requirement: 740 mm wide, 645 mm high and
548 mm deep, as well as at least 100 mm of additional
free space around the anchor.
• Recommended mounting distance: 4–6 m, max. 10 m.
• Make sure that both ground anchors are aligned opposite
to each other. The slackline must not be pull diagonally.
Assembly
Assembly of Vario-Slack WALL and  oor rack
•Proceed as shown in the drawing above ( g. 7).
• Insert one of the supplied hexagon head screws with
applied large washer through the centre hole (14 mm)
of the upper row on the Vario-Slack WALL.
•Hold the Vario-Slack WALL against the  oor rack so that it
is possible to insert the hexagon head screw into the
provided borehole in the  oor rack.
• Screw down the supplied hexagon nut and the small
washer at the rear side of the  oor rack onto the hexagon
head screw and hand-tighten the hexagon nut.
• Repeat the procedure with the other screws (total amount
of screws: 6).
• Now tighten all screws to a maximum tightening torque
of 60 Nm.
Securing the Vario-Slack GROUND to the concrete  oor
Secure the Vario-Slack GROUND according to the above
drawing ( g. 8) and handle the Vario-Slack GROUND
(weight: 36 kg) with care.
• Place the Vario-Slack GROUND at the desired position.
• Mark the position of the boreholes (d) and (dl) through the
holes in the rear transverse pipe of the Vario-Slack GROUND
on the  oor. Mark the centre of the long hole (dl) (to allow
for additional correction).
•Drill through the top layer of the  oor (max. 4 mm).
• Drill a borehole with a diameter of 20 mm and a depth of
130 mm so that the inserted female thread anchors are
 ush with the concrete  oor.
• Clean the boreholes.
•Observe the speci ed processing and hardening time for
the mortar.
• Inject the injection mortar beginning at the bottom of the
borehole making sure that there are no bubbles.
Tip: Screw the complete knurled screw into the female thread
anchor to allow for easier screwing in and for the vertical
alignment of the female thread anchor.
•Screw the female thread anchors into the boreholes by
hand without a setting tool rotating them slightly until their
upper edge is  ush with the concrete  oor.
•Make sure that the female thread anchors are vertically
aligned.
•Allow the mortar to harden completely.
•Remove the knurled screws in case you have inserted them
for screwing in and alignment.
• Position the Vario-Slack GROUND above the female thread
anchors on the  oor.
•Insert the knurled screws ( rst (d), then (dl)); then tighten
them by hand.
Fig. 7:
Washer, large
M12x160 hexagon head screw
Plastic cap
Washer, small
Plastic cap
M12 hexagon nut
Fig. 8:
(d)
(dl)
600 mm
M12 RG 18x125 female thread anchor
M12x60 knurled screw
Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 7 17.05.17 13:55

MONTAGEANLEITUNG VARIO-SLACK © Slackline-Tools 03.2017 8
Disclaimer
We do not assume any liability, in particular for the following
cases:
• The Vario-Slack GROUND or Vario-Slack WALL is not
mounted with the supplied dowels or with similar dowels.
• The Vario-Slack GROUND or Vario-Slack WALL is not
mounted on a level concrete oor but on wood or
other material.
•The supplied assembly instructions are not observed.
• The applied Vario-Slack GROUND or Vario-Slack WALL
is damaged.
We as the manufacturer do not assume any liability for injury,
consequential or incidental damage resulting from the use of
the Slackline-Tools Vario-Slack WALL. This is only applicable if
there are no other mandatory legal provisions.
When using the slackline, please observe the instruction
manual “VARIO-SLACK SETS – Vario-Slack Set GG, Vario-Slack
Set GW, Vario-Slack Set WW”.
Montageanweisung_DE_EN_Vario-Slack_02.2017_eingebettet.indd 8 17.05.17 13:55