SLC LogiQ S37020 User manual

40W Intelligent LED Driver (Constant Voltage) 09.40C T.04084V
Function introduction
Important: Read All Instructions Prior to Installation
40W CVT Dimmabel Driver
DMX& RDM RF 1-10 V ZigBee
Matc h with cont rol modul e
N
N
L
L
AC INPUT
Control Signal Input
Depending on Different
Modules
2 Channels LED Output
Control Signal Input
Depending on Different
Modules
100-277VAC Input
Control Module Assembly Tray
MTBF
Dimension
Others
193.6K hrs min. @ 230VAC full load and 25℃
ambient temperature
Over Current Yes, recovers automatically after fault condition is removed
Over Temperature
Short Circuit
Protection
Yes, recovers automatically after fault condition is removed
Yes, recovers automatically after fault condition is removed
Max. Case Temp.
85℃
Working Humidity
Working Temp.
Environment
-20 ~ +45℃ ℃
10% ~ 95% RH non-condensing
Storage Temp.
& Humidity -40 ~ +80 , 10% ~ 95% RH℃ ℃
Withstand Voltage I/P-O/P: 3.75KVAC
Isolation Resistance
Safety Standards
Safety &
EMC
EN61347-1, EN61347-2-13
I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission En55015, EN61000-3-2, EN61000-3-3
EMC Immunity En61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV
Product Data
Voltage Range 100-277V AC
Power Factor (Typ.)
Efficiency (Typ.)
Frequency Range 50/60Hz
Input
Rated Power Max. 40W
Output
Max. Current
DC Voltage
Max. 3.33A/ch,ch1+ch2=3.33A
24V DC12V DC
Max. 1.67A/ch,ch1+ch2=1.67A
LED Channel 2
Voltage Tolerance ±1%
> 0.94 @ 230VAC
Total Harmonic
Distortion
AC Current (Typ.)
88% @ 230VAC full load
THD ≤ 15% (@ full load / 230VAC)
0.47A @ 230VAC, 0.17A @ 277VAC
Leakage Current
Standby Power
Consumption
< 0.5mA /230VAC
< W0.5
Control
Dimming Interface
Dimming Range
Dimming Method
0%-100%
Plug-in type DALI (DT6/DT8), DMX/RDM, RF, 1-10V, ZigBee, Z-Wave
Pulse Width Modulation
144*84*36mm (L*W*H)
> 0.95 @ 230VAC
85% @ 230VAC full load
Inrush
Current (Typ.) COLD START 1.2A at 230VAC
• 40W independent LED driver with full isolated design
• Supplied with terminal cover and cable retainer
•
•
•
•
•
•
•
•
•
•
•
100-277VAC wide input, 2 channels 12V/24V constant voltage output
Innovative plug-in control module, easy assembly and disassembly
Work with multiple modules: DALI (DT6/DT8), DMX/RDM, RF, 1-10V, ZigBee, Z-Wave
Standby power consumption <0.5W
1500Hz PWM frequency, smooth and deep dimming to 0.1%, flicker free, no noise
Built-in active PFC function
Class Ⅱ protection against electric shock for direct or indirect contact
Protections: short circuits, over temperature, over voltage
To protect load against overheating when work with an external thermistor
Suitable for use on normally flammable surfaces
5 years warranty (3% failure rate)
• DO NOT assemble control module with power applied to the device.
DO NOT install with power applied to the device.
DO NOT expose the device to moisture.
•
•
• DO NOT change the control module within 1 minute after powering off the driver to avoid burning-out.
Safety & Warnings
emc
300MHz
ta℃
UOUT (V)
-20~45℃
2x24VD C
λ
tc℃
Iout (A) 1.67A max
Standb y Po we r( W) <0.5W
85℃
>0.9@2 30 VAC
POUT (W) 40W max
INPUT
100-24 0V ~ 0. 47 A 50/ 60 Hz
277V~ 0.17 A 50/ 60 Hz
(277V~ fo r No rt h Ame ri ca only)
Class 2 Power S up pl y Su itable for use in D ry a nd D amp Locations

Assemble the Control Module
Control module
Before assembly the control module, please power off
Match with control module
Compatible Control Modules: RF, DMX512, DMX512&RDM, DALI DT6, DALI DT8, 1-10V,ZigBee,
Z-Wave
Wiring diagram
134.5 mm
74.5mm
84 mm
144 mm
36 mm
Product Dimension
Note: for detailed wiring diagram, please refer to the user manual of corresponding control
module.
NC
NC
NC
NC
GND
D2-
D2+
D1-
D1+
DMX512 SIGNAL
CH 1 CH 2
DMX512 & RDM Control Module
0-5 0-9 0 -9
DMX512 Control Module
0-6 0-9
D1
D1
D2
D2
NC
NC
NC
NC
NC
CH 1 CH 2
PUSH DI M
L
N
D1
D2
DALI SIGNAL
DALI Control Module
DMX512&RDM control module DMX512 Control Module DALI Control Module
0-6 0-9
D1
D1
D2
D2
DALI SIGNAL
DALI DT8 Control Module
NC
NC
NC
NC
GND
NC
NC
NC
1-10V INPUT
LED
1-10V Control Module
NC
NC
DALI DT8 Control Module
GND
NC
NC
CH 1 CH 2
DIM
CCT
1-10V INPUT
1-10V Control Module
NC
NC
NC
NC
GND
NC
NC
NC
CH 1 CH 2
Learning Key
RF Control Module
PUSH
SWITCH
RF Control Module Z-Wave Control Module ZigBee Control Module
NC
NC
NC
NC
NC
NC
NC
NC
NC
CH 1 CH 2
Prog.
Z-Wave Control Module
DMX INPUT
NC
NC
NC
NC
GND
D2-
D2+
D1-
D1+
DMX512 SIGNAL
CH 1 CH 2
DMX INPUT
DALI INPUT
NC
NC
NC
NC
NC
CH 1 CH 2
DALI INPUT
1-10V Control Module for Single Color 1-10V Control Module for CCT Color
1-10V INPUT
NC
NC
NC
NC
1-10V INPUT
PUSH INPUT
NC
NC
NC
NC
NC
NC
NC
NC
NC
CH 1 CH 2
Prog.
ZigBee Control Module
1 2 3 4V
N
N
L
L
AC INPU T
DIP-SWITCH
CH 1 CH 2
Connect the input signal according
to the selected control module
LED output channel 2
LED output channel 1
Connect the input signal according
to the selected control module
100-277VAC input