Slee Maxtrax sok0054 User manual

Slee Off-Road – [MaxTrax Mount for Slee Bumper] (SOK0054) – Installation instruction 1

The entire content of this document is property of Slee Off Road and may not be used or reproduced without permission. Slee Off Road (Part Number) Rev 1.1– 01/22

700 Pine Ridge Road Golden CO 80403 Tel (303) 278 8287 1(888) 4X4 SLEE Fax (303) 278 7182

Thank you for your purchase from Slee Off-Road! If you should you have any questions or con-

cerns, please do not hesitate to contact us immediately at 1 888 4X4 SLEE or at

[email protected]om.

Slee Off-Road strives to provide comprehensive installation instructions. However, in some cir-

cumstances minor inconsistences may be encountered with instructions and or provided parts.

If you encounter such an inconsistency, please notify us, as your input is important.

Slee Off-Road guarantees all parts free from defects for one year from the original purchase

date. Slee Off-Road and Slee & Co under no circumstances will be held liable for any damages

or injuries to the users of this product(s) and or their equipment as a result of the use of this

information or parts obtained from Slee Off Road.

Slee Off-Road – [MaxTrax Mount for Slee Bumper] (SOK0054) – Installation instruction 2

The entire content of this document is property of Slee Off Road and may not be used or reproduced without permission. Slee Off Road (Part Number) Rev 1.1 – 01/22

NOTE:

The Slee SOK0054 MaxTrax Mount is for use

with Slee rear bumpers featuring a formed

metal ladder and spare tire carrier, such as the SOK1326

(200 Series Rear Bumper) or the SOK1272 (80 Series Rear

Bumper.)

If you haven’t installed the rear bumper yet, please do so

before proceeding.

QTY Parts Included

1Left MaxTrax Mount

1Right MaxTrax Mount

23/8 x 1-1/4” bolt

23/8 x 1” bolt

83/8” washer

43/8” Lock Nut

2Tie straps

Tools Required

SAE Tools

Slee Off-Road – [MaxTrax Mount for Slee Bumper] (SOK0054) – Installation instruction 3

The entire content of this document is property of Slee Off Road and may not be used or reproduced without permission. Slee Off Road (Part Number) Rev 1.01– 01/22

Correct tab orentation with wings pointed towards bolt holes. (Step1)

Remove the Hi-Lift Bracket if installed. (Step 2)

Longer hardware used for both brackets. (Step 3)

Verify the contents and tools required.

Note the correct orientation of the re-

taining tabs for the MaxTrax mount as

shown, with the wings pointing outward.

Hardware:

(1) Left MaxTrax Mount

(1) Right MaxTrax Mount

If you already have the Hi-Lift bracket

installed, remove it. If no Hi-Lift brack-

et is present, proceed to step 4.

Use one existing bolt from the Hi-Lift

bracket for the top fastener. Use two

provided longer bolts for the bottom

mounting holes.

Hardware:

(1) 3/8” x 1” Bolt (Existing)

(2) 3/8” x 1-1/4” Bolt

(3) 3/8” Washer

Slee Off-Road – [MaxTrax Mount for Slee Bumper] (SOK0054) – Installation instruction 4

The entire content of this document is property of Slee Off Road and may not be used or reproduced without permission. Slee Off Road (Part Number) Rev 1.01– 01/22

Install the brackets. (Step 4)

Arms out for MaxTrax install, down to close. (Step 5)

Add a lock to the bracket for extra security. (Step 5)

Install the MaxTrax brackets and Hi-

Lift bracket as shown. Tighten all 5

bolts.

If no Hi-Lift bracket is used, install the

MaxTrax bracket in the same location us-

ing only 4 bolts.

Hardware:

(2) 3/8” x 1” Bolt

(4) 3/8” Washer