HP BladeSystem c3000 User manual

HP BladeSystem c3000 Enclosure - Rack - Front View HP BladeSystem c3000 Enclosure - Rack - Rear View
1. Device Bays 1 thru 8 1. Local KVM interface
2. Enclosure DVD Drive 2. Interconnect Bay 1
3. Standby Onboard Administrator 3. Active Cool 100 Fans and fan bays
4. Insight Display 4. Interconnect Bay 2
5. Active Onboard Administrator 5. Enclosure Up-link and Service Port
6. Enclosure Down-link
7. iLO/Onboard Administrator Port
8. iLO/Onboard Administrator Port 2 (reserved for future)
9. Power Supplies
10. Interconnect Bay 4
11. Interconnect Bay 3
A HP BladeSystem solutions start with a either a c7000 or c3000 Enclosure. For the c3000 Enclosure, customers can add c3000 hot-
plug power supplies, HP Active Cool Fans, and an optional redundant BladeSystem Onboard Administrator module. Once the enclosure
has been selected, the following components can be added: networking interconnect modules, HP ProLiant and Integrity Server Blades,
expansion blades, and optional Insight Control for BladeSystem management software. For information on these options please visit:
http://www.hp.com/go/bladesystem .
A BladeSystem c3000 enclosure holds up to 8 server and/or storage blades plus redundant network and storage interconnects. It
includes a shared, multi-terabit high-speed mid-plane for wire-once connectivity of server blades to network and shared storage.
Power is delivered through a pooled power backplane that ensures the full capacity of the redundant hot-plug power supplies is
available to all blades.
HP BladeSystem c3000 enclosure options:
A single-phase enclosure available worldwide for use with in-rack PDUs & UPSs which accept C13/C14 power cords; or "
Alternatively, in countries with low-line (100VAC to 110VAC) power outlets, the enclosure's power supplies can be connected
directly to low-line wall outlets.
NOTE: Caution: when connecting directly to wall outlets, customers should determine the maximum amperage of the wall outlet
circuit to prevent power overload. See the Technical specification section later in this document for the individual power supply
amperage.
QuickSpecs
HP BladeSystem c3000 Enclosure
Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 1

HP 1200W Common Slot Platinum Hot Plug Power Supply Kit (up to 6 total); or
HP 1200W Common Slot -48VDC Hot Plug Power Supply Kit (up to 6 total)
c-Class Active Cool fans (between 4 and 6 total) (if not part of an enclosure bundled part number)
Redundant BladeSystem Onboard Administrator module
DVD drive (if not part of an enclosure bundled part number)
The c3000 enclosure is 6U and holds up to 8 HP c-Class server blades:
Up to 8 half-height server blades or 4 full-height server blades
Up to 4 PCI expansion blades (storage, tape, etc)
Or combinations of the above
NOTE: For information on mixing half-height server blades, full-height server blades, and expansion blades, please see the
section titled "Server Blade, Expansion Blade, and Fan Population Guidelines" later in this document.
Types of interconnect modules available: (up to 4 per enclosure)
Ethernet Interconnect Switches
Ethernet Pass-Thru modules
Virtual Connect Ethernet modules
Fibre Channel Interconnect Switches
Virtual Connect Fibre Channel modules
Fibre Channel Pass-Thru module
For additional HP BladeSystem c-Class Interconnect and Mezzanine Components:
http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html
http://h18004.www1.hp.com/products/blades/components/c-class-adapters.html
Infrastructure Management:
HP Insight Control, a product option, delivers essential infrastructure management that can help save time and money by
making it easy to deploy, migrate, monitor, control and optimize your IT infrastructure through a single, simple management
console. Insight Control supports Windows -based central management servers.
" HP Matrix Operating Environment for ProLiant, a product option, is an integrated command center that enables IT Staff
personnel to continuously analyze and optimize a converged infrastructure, while automating and reducing the cost of common
data center tasks by as much as 40 percent. This ultimately enables them to dynamically keep pace with the organization's
changing business requirements
QuickSpecs
HP BladeSystem c3000 Enclosure
Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 2

HP BladeSystem c-Class
c3000 Enclosure
A BladeSystem c3000 enclosure holds up to 8 server blades and up to 4 expansion blades (not exceeding 8
total blades) plus redundant or non-redundant network and storage interconnects. It includes a shared,
multi-terabit high-speed mid-plane for wire-once connectivity of server blades to network and shared
storage. Power is delivered through a pooled power backplane that ensures the full capacity of the power
supplies is available to all blades.
Each c3000 enclosure is built with the following functions:
Up to 8 half-height, 4 full-height server blades and/or 4 expansion blades per enclosure.
NOTE: For information on mixing half-height server blades, full-height server blades, and expansion
blades, please see the section titled "Server Blade, Expansion Blade, and Fan Population Guidelines"
later in this document.
Up to 3 redundant interconnect fabrics (Ethernet, FC, iSCSI, SAS, etc.) supported simultaneously
within the enclosure.
A single-phase power subsystem for flexibility in connecting to datacenter power, or to UPS's or to
low-line wall outlets.
Choice of AC or DC power supplies.
PARSEC enclosure design - Parallel, redundant and scalable cooling and airflow design.
Up to six (6) Active Cool fans
Fully redundant design providing no single point of failure; redundant interconnections between
servers and interconnect modules; a mid-plane with no active components; redundant cooling using
Active Cool fans.
Best performance per watt - lower wattage per server blade, in comparison to rack-mounted
servers
Full AC redundancy with no power zones.
Single or dual Onboard Administrator management modules
An Onboard Administrator management module is built in to the enclosure with the following functions:
Robust, multiple enclosure setup and control.
Reports asset and inventory information for the devices in the enclosure.
Reports thermal and power information, including real-time actual power usage per server and per
enclosure.
Front-mounted Insight Display for easy management at the deployment site.
Integrated access to all server blade iLOs from a single cable.
Provides integrated access to interconnect bay device management ports from the single Onboard
Administrator cable.
Single sign-on capability for all devices in the enclosure
Role-based security locally and/or with LDAP directory services.
Provides a wizard-based initial setup process for easy configuration.
An optional DVD drive for local software deployment, and HP SmartStart deployment
An optional local KVM interface for connection to KVM switches.
A BladeSystem c3000 enclosure provides the following benefits:
With local and remote hardware management integrated across the solution, one full enclosure can
be managed as easily as one server.
Scalable: Management and network interconnects extend scalability beyond a single enclosure,
allowing resources to be pooled and shared across multiple enclosures.
Investment protection: Accommodates multiple server and network designs in one enclosure.
Lower costs per server, in comparison to rack-mounted servers
QuickSpecs
HP BladeSystem c3000 Enclosure
HP BladeSystem c-Class Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 3

Lower power consumption, in comparison to rack-mounted servers.
Service and management: Allows multiple administrators to remotely access and maintain multiple
servers & interconnect devices simultaneously.
HP ProLiant & Integrity
Server Blades
Delivering best-in-class performance, choice and reliability on AMD Opteron™, Intel® Xeon® and Intel®
Itanium® processors for Windows, Linux, Solaris, OpenVMS, or HP-UX based servers; the HP portfolio of
server blades supports a variety of application requirements for scale-out architectures. HP offers one-,
two-, four- and eight -processor server blades, with the widest range of performance, and form factors.
For information please visit: http://www.hp.com/go/bladesystem .
HP D2200sb Storage Blade Direct attached storage
The D2220sb Storage Blade delivers direct attached storage for c-Class Gen8 blade servers, with support
for up to twelve hot plug small form factor (SFF) SAS or SATA Midline hard disk drives or SAS/SATA SSDs.
The enclosure backplane provides a PCI Express connection to the adjacent c-Class server blade and
enables high performance storage access without any additional cables. The D2220sb Storage Blade
features an onboard Smart Array P420i controller with 2GB flash-backed write cache, for increased
performance and data protection. Up to eight D2220sb storage devices can be supported off a single
BladeSystem c7000 enclosure for up to 115.2 TB of capacity.
Two ways to create shared storage with the D2220sb
Use HP StoreVirtual VSA software to turn the D2220sb into an iSCSI SAN for use by all servers in the
enclosure and any server on the network. HP VSA software is installed in a virtual machine on a VMware
ESX host server adjacent to the D2220sb. HP StoreVirtual VSA turns the D2220sb into a scalable and robust
iSCSI SAN, featuring storage clustering for scalability, Network RAID for storage failover, thin provisioning,
snapshots, remote replication, and cloning. Expand capacity within the same enclosure or to other
BladeSystem enclosures by adding additional D2220sb Storage Blades and HP VSA licenses. A cost
effective bundle of the D2220sb Storage Blade and a HP StoreVirtual VSA license makes purchasing
convenient. If storage needs increase, add HP P4300 or P4500 systems externally and manage everything
via a single pane of glass.
The HP StoreEasy 3830 Gateway Storage Blade is a flexible storage server solution for BladeSystem
environments. Combine the StoreEasy 3830with the D2220sb Storage Blade to enable file serving and
iSCSI shared storage inside the BladeSystem enclosure.
NOTE: The D2220sb requires a c3000 Enclosure configuration with 6 fans
For more information, please visit:
http://h18004.www1.hp.com/products/quickspecs/14507_na/14507_na.html
HP Ultrium Tape Blades Tape blades are ideal for HP BladeSystem c-Class customers who need a data protection solution but are
not connected into a Storage Area Network (SAN). They provide direct attach data protection for the
adjacent server and network backup protection for all other data within the enclosure. The HP tape blades
are the industry's first bladed tape drives and are developed exclusively for the BladeSystem c-Class
enclosures.
For more information, please visit:
http://h18000.www1.hp.com/products/quickspecs/12729_na/12729_na.html
QuickSpecs
HP BladeSystem c3000 Enclosure
HP BladeSystem c-Class Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 4

HP BladeSystem c-Class
Interconnect Options
HP offers one of the broadest selections of interconnect fabric options in the industry to provide network,
SAN/network attached storage (NAS), and cluster connectivity.
HP BladeSystem interconnects provide:
New HP Virtual Connect devices, designed to reduce networking costs and simplify network
configuration and provisioning.
Seamless integration of Ethernet, FC, iSCSI, and SAS fabrics: Standard-based switch options include
Cisco, Brocade, and HP products that integrate within your existing standards.
Built-in redundancy: rear-mounting interconnect modules designed for redundant interconnections
between server blades and switches.
Cable reduction: Interconnect switches provide up to 32-to-1 network cable reductions per server
blade enclosure
HP BladeSystem c-Class Interconnect and Mezzanine Components:
http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html
http://h18004.www1.hp.com/products/blades/components/c-class-adapters.html
Factory Express Portfolio
for Servers and Storage
HP Factory Express offers configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading, asset
tagging and custom packaging. HP products supported through Factory Express include: a wide array of
servers and storage: HP Integrity, HP ProLiant & HP ProLiant & Integrity Server Blades, HP BladeSystem,
HP 9000 servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable
network switches.
For more information on Factory Express services for your specific server model please contact your sales
representative or go to: http://www.hp.com/go/factory-express
HP Simple Configurator SCE is a guided self service tool to help sales and non technical people provide customers with initial
configurations in 3 to 5 minutes. You may then send the configuration on for configuration help, or use in
your existing ordering processes. If you require "custom" rack configuration or configuration for products
not available in SCE, please contact HP's Customer Business Center or an Authorized Partner for assistance.
http://www.hp.com/products/configurator
HP Insight Management
software
Insight Management Managing the growing number of servers can be complex and expensive for
your organization. IT managers need to address changing business needs with
tools that meet the challenges of managing today's complex Datacenters.
HP Insight Management lowers the cost of running your HP ProLiant servers
by providing you with best-in-class management tools, including HP Insight
Control, HP Virtual Connect Enterprise Manager (VCEM), and HP Matrix
Operating Environment. Insight Management increases your productivity and
reduces your operating costs to get you higher value from your HP ProLiant
servers.
Electronic download of Insight Management Media
QuickSpecs
HP BladeSystem c3000 Enclosure
HP BladeSystem c-Class Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 5

Insight Management software media is available for free download (not
including license entitlement certificates) at this website:
http://www.hp.com/go/insightupdates .
Software media available for download includes:
HP Insight Control
HP Insight Control for Microsoft® System Center
HP Insight Control for VMware vCenter Server
HP Virtual Connect Enterprise Manager (VCEM)
HP Matrix Operating Environment
Customers will receive an Insight Control or Matrix Operating Environment
license entitlement certificate via physical shipment or email. The license
entitlement certificate must be redeemed online or via fax in order to
obtain the license activation key(s).
One year of 24x7 Software Technical Support and Updates are included with
your purchased licenses.
HP provides a complete range of installation and support services to
ensure the successful deployment and operations of your server
infrastructure. For more information about support services and licensing
options, see the following website:
http://www.hp.com/go/insightsoftware
Insight Software Media Kit (DVDs)
Physical media (DVDs) are also available for purchase from HP or from your
authorized reseller (PN 436222-B21)
Service Pack for ProLiant
(SPP)
Customers should use the HP Service Pack for ProLiant to update firmware,
drivers, and related utilities.:
Main SPP page: www.hp.com/go/spp
SPP download page: www.hp.com/go/spp/download
ProLiant Onboard
Administrator
HP ProLiant Onboard Administrator (powered by the HP Integrated Lights-Out
2 management processor) simplifies server setup, health monitoring, power
and thermal control, and lights-out remote administration of ProLiant ML, DL,
and BL servers. HP ProLiant Onboard Administrator functions without
additional software, and can be accessed from any location via a web browser.
It works hand-in-hand with HP Systems Insight Manager, Insight Control, and
the Matrix Operating Environment for ProLiant helping customers unlock the
value of the ProLiant platform and deliver the highest possible quality of IT
service to the business. See: www.hp.com/go/ProLiantOA
HP Insight Control HP Insight Control, a product option, delivers essential infrastructure
management that can help save time and money by making it easy to deploy,
migrate, monitor, remote control, and optimize your IT infrastructure through
a single, simple management console. For more information, see
http://www.hp.com/go/insightcontrol .
HP Insight Control includes one year of 24 x 7 HP Software Technical Support
and Update Service ensuring rapid access to HP support staff and proactive
QuickSpecs
HP BladeSystem c3000 Enclosure
HP BladeSystem c-Class Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 6

delivery of software updates. For more information about this service, please
visit: http://www.hp.com/services/insight
HP Matrix Operating
Environment
The HP Matrix Operating Environment (Matrix OE) for ProLiant and Integrity
servers is an integrated command center that helps you instantly adjust to
dynamic business demands. This advanced infrastructure management
software lets you reduce the cost of common data center tasks by up to 40
percent while keeping pace with your changing business.
The HP Matrix OE includes the automated provisioning, optimization, and
recovery management capabilities for HP CloudSystem Matrix, the ideal
platform for private cloud and Infrastructure as a Service (IaaS). For more
information, see http://www.hp.com/go/matrixoe .
HP Power Advisor The HP Power Advisor is a tool provided by Hewlett-Packard to assist in the estimation of power
consumption and proper selection of components including power supplies at a system, rack, and multi-
rack level. A variety of additional features are also provided including a condensed bill of materials, a cost
of owner ship calculator, and a power report. The HP Power Advisor allows for the mixing of rack, blade,
and other products in a single environment.
Available at: http://www.hp.com/go/hppoweradvisor
Warranty Warranty - This product is covered by a global limited warranty and supported by HP Services and a
worldwide network of HP Authorized Channel Partners. Hardware diagnostic support and repair is available
for three years from date of purchase. Support for software and initial setup is available for 90 days from
date of purchase. Additional support may be covered under the warranty or available for an additional fee.
Enhancements to warranty services are available through HP Care Pack services or customized service
agreements.
Enclosure: Three-year parts and labor, on-site limited global warranty. Certain restrictions and
exclusions apply
Enclosure options: Fans, Power Supplies, BladeSystem Onboard Administrator, 1 Year parts only or
enclosure warranty
HP BladeSystem Interconnects: 1 Year parts and labor, on-site regardless of the warranty period for
the system in which they are installed
HP Storage Fibre Channel switches have a maximum warranty period of one (1) year regardless of
the warranty period for the system in which they are installed
Hard drives have either a one year or three year warranty; refer to specific hard drive QuickSpecs for
details.
QuickSpecs
HP BladeSystem c3000 Enclosure
HP BladeSystem c-Class Overview
DA - 12790 North America — Version 55 — December 10, 2013 Page 7

Service and Support HP Technology Services for Industry Standard Servers and BladeSystem
Capitalizing on HP ProLiant server and HP BladeSystem capabilities requires a service partner who
understands your increasingly complex business technology environment. That's why it makes sense to
team up with the people who know HP infrastructure hardware and software best - the experienced
professionals at HP Services.
Protect your business beyond warranty with HP Care Pack Services
HP Care Pack services offer complete care and support expertise with committed response choices
designed to meet your IT and business needs.
HP Foundation Care services offer scalable reactive support-packages for HP servers and software. You
can choose the type and level of service that is most suitable for your IT and business needs. HP Proactive
Care delivers high levels of system availability through proactive service management and advanced
technical response. HP Datacenter Care provides highly flexible environmental support to address unique
customer business needs.
Choose recommended services for your c3000 BladeSystem enclosure or contact your HP sales
representative or authorized HP ServiceOne partner for additional HP Care Pack services information
Recommended HP Care Pack Services for your HP product
Optimized Care 3-Year HP 6 hour Call to Repair Response, Proactive Care
Combined reactive and proactive support for hardware and software helping optimize your systems and
delivering high levels of availability through proactive service management and advanced technical
response. Hardware problem resolution to return the hardware in operating condition within 6 hours of the
initial service request. A Technical Account Manager, as your single point of contact, will own your call or
issue end to end until resolved.
http://h20195.www2.hp.com/v2/GetPDF.aspx/4AA3-8855EEE.pdf
HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for c3000 enclosure
Provides for hardware installation (c-Class ProLiant and Integrity server blades, storage blades, Ethernet
Interconnects and Virtual Connect) and software installation and startup of a BladeSystem c3000
Infrastructure in a single enclosure including deployment of OS on all blades or deployment of OS (two
blades) and HP Insight Control, plus Server Deployment (formerly RDP).
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW.pdf
HP Installation and Startup Service for HP BladeSystem c-Class Enhanced Network
Provides for the configuration and testing of BladeSystem Ethernet interconnect switches and Virtual
Connect to facilitate proper implementation of network protocols and access to advanced features.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4aa0-5969ENW.pdf
Standard Care 3-Year HP 24x7 4 hour response, Proactive Care Service
This service gives you combined reactive and proactive support including rapid access to our Advanced
Solution Center to manage and prevent problems and a Technical Support Specialist with a broad level of
technical knowledge that will engage with additional technical expertise as needed from HP's vast global
resources.
http://h20195.www2.hp.com/v2/GetPDF.aspx/4AA3-8855EEE.pdf
HP Installation and Startup Service for HP BladeSystem c-Class Infrastructure for c3000 enclosure
Provides for hardware installation (c-Class ProLiant and Integrity server blades, storage blades, Ethernet
Interconnects and Virtual Connect) and software installation and startup of a BladeSystem c3000
Infrastructure in a single enclosure including deployment of OS on all blades or deployment of OS on two
QuickSpecs
HP BladeSystem c3000 Enclosure
Service and Support
DA - 12790 North America — Version 55 — December 10, 2013 Page 8

blades and HP Insight Control, plus Server Deployment (formerly RDP).
http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA0-5964ENW.pdf
HP Installation and Startup Service for HP BladeSystem c-Class Enhanced Network
HP Provides for the configuration and testing of BladeSystem Ethernet interconnect switches to facilitate
proper implementation of network protocols and access to advanced features.
http://h20195.www2.hp.com/V2/GetPDF.aspx/4aa0-5969ENW.pdf
Related Services HP Proactive Care Personalized Support - Environmental Option
The Personalized Support option provides an assigned Account Support Manager who can bring best
practices from across the industry plus extra technical skills to your IT team. This option is only available
as an add-on to HP Proactive Care Support.
HP Proactive Select Service
Provides a flexible way to purchase HP best-in-class consultancy and technical services. You can buy
Proactive Select Service Credits when you purchase your hardware and then use the credits over the next
12 months. http://h20195.www2.hp.com/V2/GetPDF.aspx/4AA2-3842ENN.pdf
Additional HP Care Pack services can be found at: http://www.hp.com/go/cpc
Insight Online/Insight
Remote Support
HP Insight Remote Support provides 24 X 7 remote monitoring, proactive notifications, and problem
resolution. This comes at no additional cost with your HP solution. Learn more about Insight Remote
Support http://www.hp.com/go/insightremotesupport and Insight Online
http://www.hp.com/go/insightonline
NOTE: Insight Remote Support is a prerequisite for Proactive Care. All blades within a single HP
BladeSystem enclosure must be at the same service level.
HP Support Center Personalized online support portal with access to information, tools and experts to support HP business
products. Submit support cases online, chat with HP experts, access support resources or collaborate with
peers. Learn more http://www.hp.com/go/hpsc
HP's Support Center Mobile App allows you to resolve issues yourself or quickly connect to an agent for
live support. Now, you can get access to personalized IT support anywhere, anytime.
HP Insight Remote Support and HP Support Center are available at no additional cost with a HP warranty,
HP Care Pack or HP contractual support agreement.
NOTE: HP Support Center Mobile App is subject to local availability.
Parts and Materials HP will provide HP-supported replacement parts and materials necessary to maintain the
covered hardware product in operating condition, including parts and materials for available
and recommended engineering improvements.
Parts and components that have reached their maximum supported lifetime and/or the
maximum usage limitations as set forth in the manufacturer's operating manual, product
quick-specs, or the technical product data sheet will not be provided, repaired, or replaced as
part of these services.
The defective media retention service feature option applies only to Disk or eligible SSD/Flash Drives
replaced by HP due to malfunction
For more information To learn more on HP ProLiant servers and HP BladeSystem servers, please contact your HP sales
representative or HP Authorized ServiceOne partner. Or visit: www.hp.com/services/bladesystem
QuickSpecs
HP BladeSystem c3000 Enclosure
Service and Support
DA - 12790 North America — Version 55 — December 10, 2013 Page 9

HP BladeSystem
c-Class Server Blade
Enclosures
NOTE: HP does not allow factory integration of options into pre-configured models. Any additional options
purchased will be shipped separately.
NOTE: If you desire a custom configuration please see "Configuration Information - Factory Integrated
Models" section of this QuickSpecs.
HP BLc3000 Platinum Enclosure with 4 AC Power Supplies 6 Fans ROHS 8 Insight Control
Licenses
NOTE: Includes 4 1200W AC Common Slot Platinum Plus Hot Plug Power Supplies, 6
Active Cool 100 Fans, DVD drive, Rail Kit, Onboard Administrator DDR2 module, 4 6ft
C13 to C14 PDU power cords, 7 bay blanks, and 8 Insight Control Licenses.
696908-B21
HP BLc3000 Platinum Enclosure with 4 AC Power Supplies 6 Fans ROHS Trial Insight
Control License
NOTE: Includes 4 1200W AC Common Slot Platinum Plus Hot Plug Power Supplies, 6
Active Cool 100 Fans, DVD drive, Rail Kit, Onboard Administrator DDR2 module, 4 6ft
C13 to C14 PDU power cords, 7 bay blanks, and 8 Insight Control Trial Licenses.
696909-B21
QuickSpecs
HP BladeSystem c3000 Enclosure
Pre-Configured Models
DA - 12790 North America — Version 55 — December 10, 2013 Page 10

NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, HP recommends contacting your local sales representative for information on Factory Integrated Model product offerings and
requirements.
For a complete configuration of the HP BladeSystem, please do the following:
Step 1: Select desired model, configuration and quantity of HP ProLiant server and
expansion blades
NOTE: HP BladeSystem c3000 and c7000 enclosures may support G1 through Gen8 server blades and Integrity server blades in the
same enclosure, subject to support requirements of the Onboard Administrator. Please review the links below to specific blades for
details.
NOTE: HP ProLiant G8 server blades and certain options require the latest version of the Onboard Administrator firmware. This
firmware release may also require other subsystem firmware upgrades. For information on the latest firmware versions, please see
the Blades Firmware Maintenance website at: http://h18004.www1.hp.com/products/blades/components/c-class-compmatrix.html .
NOTE: For server and expansion blade (storage, tape, and PCI Expansion) information, please visit:
http://www.hp.com/go/bladesystem .
Step 2: Determine quantity of HP BladeSystem c-3000 Enclosures to purchase and choose
Required Options
(One of the following from each list unless otherwise noted):
Select Base Server Blade Enclosure Configuration
HP BladeSystem c3000 c-
Class Server Blade
Enclosures
Choose one of the following CTO enclosures
HP BLc3000 Platinum Configure-to-order Enclosure with 6 Fans ROHS Trial Insight
Control License
NOTE: Includes no AC power supplies, 6 Active Cool 100 Fans, a DVD drive, rack rails, and
a single DDR2 Onboard Administrator module.
696910-B21
HP Integrity BLc3000 CTO Enclosure
NOTE: Includes no AC power supplies, 6 Active Cool 100 Fans, a DVD drive, rack rails, and
a single DDR2 Onboard Administrator module.
AH257C
Select additional optional enclosure options:
HP Redundant Onboard
Administrator
HP BLc3000 Dual DDR2 Onboard Administrator
NOTE: HP ProLiant G8 server blades and certain options require the latest version of the
Onboard Administrator firmware. This firmware release may also require other
subsystem firmware upgrades. For information on the latest firmware versions, please
see the Blades Firmware Maintenance website at:
http://h18004.www1.hp.com/products/blades/components/c-class-compmatrix.html .
488100-B21
Additional HP c3000
Enclosure Power Supplies
NOTE: Please choose AC or DC power supplies.
NOTE: HP AC Common Slot Power supplies meet 80 Plus Platinum or Silver power
efficiency requirements: (Platinum (94%) - PN 656364-B21and Silver (90%) - PN
500172-B21).The 80 PLUS program is a unique forum that unites electric utilities, the
computer industry, and consumers in an effort to bring energy efficient technology
solutions to the marketplace. 80 Plus independently tests power supply efficiency and
publically posts the results on 80Plus.org.
NOTE: HP highly recommends using the HP Power Advisor tool to ensure the number of
QuickSpecs
HP BladeSystem c3000 Enclosure
Configuration Information Factory Integrated Models
DA - 12790 North America — Version 55 — December 10, 2013 Page 11

power supply options you have selected can fully support your BladeSystem
configuration. The HP Power Advisor tool can be downloaded at
www.hp.com/go/hppoweradvisor .
NOTE: For a full enclosure, you can either order 4 or more power supplies to support a
N+1 redundant configuration or 6 power supplies to support a N+N redundant
configuration.
NOTE: Each enclosure must include only 1 type of power supply. All power supplies
must be AC or all DC power supplies. The Onboard Administrator will exhibit a mismatch
error due to mixed power supplies until all power supplies are matched.
HP 1200W Common Slot Platinum Plus Hot Plug Power Supply Kit
NOTE: Platinum power supplies required to enable power discovery services.
NOTE: Include a 6ft C13 to C14 PDU power cord.
656364-B21
HP 1200W Common Slot -48VDC Hot Plug Power Supply Kit
NOTE: DC power supplies contain a -48V DC power cord designed for in-rack DC power
rectifiers.
NOTE: When this DC power supply (437573-B21) is ordered as a factory integrated
enclosure option, standard AC supplies are not included in the order shipment. When
this DC power supply is ordered with an enclosure, but not factory integrated, standard
AC power supplies are included in the order shipment and DC power supplies are shipped
separately.
437573-B21
HP c3000 KVM Modules
and Adapters
HP BLc3000 KVM Option
NOTE: For use with in-rack KVM switches.
437575-B21
HP KVM USB2 1-pack Interface Adapter
NOTE: Order one KVM Adapter per c3000 enclosure, to support KVM switches accepting
RJ45 cables. Please see the Options section of this QuickSpecs for additional product
information.
AF603A
HP Optional Power Cords HP C20 - C13 WW 250V 15Amp 2.0m Jumper Cord
NOTE: For use with PDU's accepting C20 power cords.
NOTE: Order 1 for each power supply.
AF590A
HP C13 - Nema 6-15P US 250V 15A JP 3.6m Power Cord A0N33A
Step 3: Select additional (one to four) interconnects.
The following is a list of various HP BladeSystem c-Class interconnect modules (Virtual Connect, Ethernet, Fibre Channel, and SAS
interconnects). A pair of interconnects must be ordered if redundancy is required. For detailed interconnect options consult the specific
interconnect QuickSpecs: http://h18004.www1.hp.com/products/blades/components/c-class-interconnects.html .
NOTE: Options for specific c-Class interconnects are NOT included in the list below. Consult the individual interconnect QuickSpecs to
obtain part numbers for interconnect options such as cables, SFPs, etc.
NOTE: Interconnect Bay 1 must contain one of the "Ethernet" interconnect modules.
HP BladeSystem
c-Class Ethernet
Interconnects
HP Virtual Connect Flex-10/10D Module for c-Class BladeSystem 638526-B21
HP Virtual Connect Flex-10 10Gb Ethernet Module for c-Class BladeSystem 455880-B21
HP 6125G/XG Ethernet Blade Switch 658250-B21
HP 6125G Ethernet Blade Switch 658247-B21
HP 6120G/XG Ethernet Blade Switch 498358-B21
HP 6120XG Blade Switch 516733-B21
HP 1GB Ethernet Pass-Thru Module for c-Class BladeSystem 406740-B21
HP 10GbE Ethernet Pass-Thru Module for c-Class BladeSystem 538113-B21
Cisco Catalyst 1/10GbE 3120X Blade Switch 451439-B21
QuickSpecs
HP BladeSystem c3000 Enclosure
Configuration Information Factory Integrated Models
DA - 12790 North America — Version 55 — December 10, 2013 Page 12

Cisco Catalyst 1GbE 3120G Blade Switch 451438-B21
Cisco Catalyst Blade Switch 3020 for HP c-Class BladeSystem 410916-B21
HP Cisco B22HP Fabric Extender for BladeSystem c-Class 641146-B21
HP Cisco B22HP Fabric Extender with 16 FET for BladeSystem c-Class 657787-B21
NOTE: The Cisco Fabric Extender for HP BladeSystem with 16 FET - (PN 657787-B21),
comes packaged with 16 Cisco Fabric Extender Transceivers. These Cisco transceivers
can be used to connect the Fabric Extender with a parent Nexus 5000 over optical cable
up to 100 meters using OM3 grade fiber.
HP GbE2c Layer 2/3 Ethernet Blade Switch 438030-B21
NOTE: HP Virtual Connect FlexFabric 10Gb/24-port Module for c-Class BladeSystem
(P/N 571956-B21) is not compatible with the c3000 enclosure
HP SAS Switch HP 6Gb SAS Switch Single Pack for HP BladeSystem c-Class BK763A
HP 6Gb SAS Switch Dual Pack for HP BladeSystem c-Class BK764A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/13960_na/13960_na.html
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/13170_na/13170_na.html
HP BladeSystem
c-Class FC SAN
Interconnects
HP Virtual Connect 8Gb 24-port Fibre Channel Module for c-Class BladeSystem 466482-B21
HP Virtual Connect 8Gb 20-port Fibre Channel Module for c-Class BladeSystem 572018-B21
HP 4GB Fibre Channel Pass-thru Module for c-Class BladeSystem 403626-B21
Brocade 8/12c SAN Switch for BladeSystem c-Class AJ820B
Brocade 8/24c SAN Switch for BladeSystem c-Class AJ821B
Brocade 8/24c Power Pack+ SAN Switch for BladeSystem c-Class AJ822B
Cisco MDS 8/12c Fabric Switch for HP BladeSystem c-Class AW563A
Cisco MDS 8/24c Fabric Switch for HP BladeSystem c-Class AW564A
HP MDS 8/12c Fabric Switch 12-port Upgrade LTU
NOTE: Licensed per switch.
TA804A
HP MDS Fabric Manager Server for BladeSystem c-Class LTU
NOTE: Licensed per switch.
TC316A
HP MDS Enterprise Package for BladeSystem c-Class LTU
NOTE: Licensed per switch.
TC317A
HP MDS Fabric Manager Server Enterprise Package for BladeSystem c-Class LTU
NOTE : Licensed per switch.
TC318A
Step 4: Select rack power distribution for installing the enclosure into a rack.
NOTE: A pair of PDUs must be ordered for AC Feed redundancy. If AC redundancy is not required, a single PDU or UPS may be
acceptable.
HP Monitored Power
Distribution Unit
HP 8.6kVA 24A Single Input Three Phase NA/JP Monitored Power Distribution Unit AF504A
HP Two C13 PDU Extension Bar AF500A
QuickSpecs
HP BladeSystem c3000 Enclosure
Configuration Information Factory Integrated Models
DA - 12790 North America — Version 55 — December 10, 2013 Page 13

Step 5: Select Wall Outlet Power Cords
(For connection to standard wall outlets)
NOTE: Select one wall outlet power cord for each power supply when plugging the power supplies into a wall outlet.
NOTE: Wall Outlet power cords should only be used with low-line (100v to 110V) power sources. If high-line power outlets are required,
safety regulations require the use of a PDU or a UPS between the c3000 enclosures power supplies and wall outlets.
NOTE: A standard 6ft PDU power cord (C13 to C14) is included with each AC power supply, so these wall outlet power cords are not
required if you plan to plug the power supplies into a PDU or UPS.
Order the appropriate power cord for your countries standard electrical outlets.
HP Power Cords HP C13 - Nema 5-15P US/CA 110V 10Amp 1.83m Power Cord
NOTE: HP Power cord (6 ft) 1.83 meter 10A C-13-UL domestic power cord, for grounded
USA 110V wall outlets.
AF556A
HP C13 - JIS C8303 JP 100V 12Amp 2.0m Power Cord
NOTE: HP Power cord 2 meter C13 Japan low-line power cord, for Japanese 100V wall
outlets.
AF572A
HP C20 - C13 WW 250V 15Amp 2.0m Jumper Cord
NOTE: For use with PDUs accepting C20 power cords.
AF590A
NOTE: For additional power cable information, please visit:
http://h18000.www1.hp.com/products/servers/proliantstorage/power-
protection/options/power-cable.html
QuickSpecs
HP BladeSystem c3000 Enclosure
Configuration Information Factory Integrated Models
DA - 12790 North America — Version 55 — December 10, 2013 Page 14

HP c3000 Enclosure
Options
HP BLc7000 Miscellaneous Blanks Option Kit 412148-B21
NOTE: Contains 1 each of c3000/c7000 Active Cool Fan blank, c3000/c7000
interconnect module blank, c7000 Onboard Administrator blank, c3000 local KVM blank,
c3000 power supply blank, c7000 power supply blank, c3000 DVD blank, and a c3000
mini-divider.
NOTE: This kit should only be ordered to replace lost or damaged blanks.
HP BLc7000 Server Blank w/Coupler Option
NOTE: This is option contains one half-height device blank and a coupler that can be
used for the c3000 and c7000 enclosures.
NOTE: Order quantity of one 412150-B21 for filling a half-height bay; the coupler is not
used.
NOTE: Order quantity of two 412150-B21 for filling a full-height bay. One coupler is
installed between the two half-height blanks to be connected together to create a full-
height blank.
NOTE: This kit should only be ordered to replace lost or damaged blanks.
412150-B21
HP c3000 Rack Brackets HP BLc3000 10000 Series Rack Shipping Bracket Option
NOTE: Required when shipping a c3000 enclosure in a HP 10000 series rack. Please
order 1 kit per enclosure.
461384-B21
HP Onboard Administrator HP BLc3000 DDR2 Onboard Administrator Rotate LCD Kit
NOTE: HP ProLiant G8 server blades and certain options require the latest version of the
Onboard Administrator firmware. This firmware release may also require other
subsystem firmware upgrades. For information on the latest firmware versions, please
see the Blades Firmware Maintenance website at:
http://h18004.www1.hp.com/products/blades/components/c-class-compmatrix.html .
NOTE: For field upgrades of previous generation enclosures only.
NOTE: This Redundant Onboard Administrator module supports either single mode, or
dual/redundant mode Onboard Administrators.
590863-B21
HP BLc3000 Dual DDR2 Onboard Administrator
NOTE: Second Onboard Administrator Module for the DDR2 OA module.
NOTE: Support for second Order Administrator Module for c3000 Enclosure.
NOTE: This module fits into an HP c3000 DDR2 Onboard Administrator.
488100-B21
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 15

HP c-Class Power Supply NOTE: HP BladeSystem Power supplies meet multiple Energy Efficiency Initiatives:
1200W, Climate Savers Computing Initiative SILVER and ECOS Consulting 80 Plus;
(Platinum (94%) - PN 656364-B21 and Silver (90%) - PN 500172-B21).
NOTE: The 80 PLUS program is a unique forum that unites electric utilities, the
computer industry, and consumers in an effort to bring energy efficient technology
solutions to the marketplace. 80 Plus independently tests power supply efficiency and
publically posts the results on 80Plus.org.
NOTE: For c-3000 Low-line Power Cords, please order the appropriate power cord for
your countries standard electrical outlets. Please see Step 5 above for power cord part
numbers.
HP 1200W Common Slot Platinum Plus Hot Plug Power Supply Kit
NOTE: Platinum power supplies required to enable power discovery services
NOTE: Includes a 6ft C13 to C14 PDU power cord.
656364-B21
HP 1200W Common Slot -48VDC Hot Plug Power Supply Kit
NOTE: DC power supplies contain a -48V DC power cord designed for in rack DC power
rectifiers.
NOTE: When this DC power supply (437573-B21) is ordered as a factory integrated
enclosure option, standard AC supplies are not included in the order shipment. When
this DC power supply is ordered with an enclosure, but not factory integrated, standard
AC power supplies are included in the order shipment and DC power supplies are shipped
separately.
437573-B21
HP c3000 KVM Module and
Adapters
HP BLc3000 KVM Option
NOTE: For use with in-rack KVM switches
437575-B21
HP KVM USB2 1-pack Interface Adapter
NOTE: Order one KVM Adapter per c3000 enclosure, to support KVM switches accepting
RJ45 cables. Please see the Options section of this QuickSpecs for additional product
information.
AF603A
HP BladeSystem
c-Class Ethernet
Interconnects
HP Virtual Connect Flex-10 10Gb Ethernet Module for c-Class BladeSystem 455880-B21
HP 6125G Ethernet Blade Switch 658247-B21
HP 6125G/XG Ethernet Blade Switch 658250-B21
HP 6120G/XG Ethernet Blade Switch 498358-B21
HP 6120XG Blade Switch 516733-B21
HP 1GB Ethernet Pass-Thru Module for c-Class BladeSystem
NOTE: The Ethernet Pass-Thru Module is shipped as a single unit and should be ordered
in quantities of two.
406740-B21
Cisco Catalyst 1/10GbE 3120X Blade Switch 451439-B21
Cisco Catalyst 1GbE 3120G Blade Switch 451438-B21
Cisco Catalyst Blade Switch 3020 for HP c-Class BladeSystem 410916-B21
HP GbE2c Layer 2/3 Ethernet Blade Switch 438030-B21
NOTE: HP Virtual Connect FlexFabric 10Gb/24-port Module for c-Class BladeSystem
(P/N 571956-B21) is not compatible with the c3000 enclosure
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 16

HP BladeSystem
c-Class FC SAN
Interconnects
HP Virtual Connect 8Gb 24-port Fibre Channel Module for c-Class BladeSystem 466482-B21
HP Virtual Connect 8Gb 20-port Fibre Channel Module for c-Class BladeSystem 572018-B21
HP 4GB Fibre Channel Pass-thru Module for c-Class BladeSystem 403626-B21
Brocade SAN Switch for HP
BladeSystem c-Class
Brocade 8/12c SAN Switch for BladeSystem c-Class AJ820B
Brocade 8/24c SAN Switch for BladeSystem c-Class AJ821B
Brocade 8/24c Power Pack+ SAN Switch for BladeSystem c-Class AJ822B
Brocade 4/12 SAN Switch Upgrade RTU for HP BladeSystem c-Class AE373A
Cisco MDS Fabric Switch
for HP BladeSystem c-
Class
Cisco MDS 8/12c Fabric Switch for HP BladeSystem c-Class AW563A
Cisco MDS 8/24c Fabric Switch for HP BladeSystem c-Class AW564A
HP MDS Fabric Manager Server Enterprise Package for BladeSystem c-Class LTU TC318A
HP B-series 8/12c SAN Switch for BladeSystem c-Class 12-port Upgrade RTU T5517A
Cisco MDS 9124e Switch for BladeSystem c-Class 12-port Upgrade LTU T5169A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/13821_na/13821_na.html
HP Insight Software HP Insight Control
HP Insight Control for BladeSystem including 1yr 24x7 Support Enclosure 8 Svr FIO
Electronic License
C6N32ABE
HP Insight Control for BladeSystem including 1yr 24x7 Support Enclosure 16Svr FIO
Electronic License
C6N33ABE
HP Insight Control Server Provisioning Media Kit
NOTE: HP Insight Control 7.2 introduces Insight Control server provisioning, a new
capability ideal for multi-server OS and firmware provisioning to ProLiant and
BladeSystem servers. Insight Control server provisioning is included and licensed as part
of HP Insight Control. A media kit, "HP Insight Control server provisioning USB media kit"
(# BD883A), including a USB, is available for customers who require a physical copy of
the media loaded with Insight Control server provisioning software. Please note that
this media kit is separate and in addition to the "HP Insight Management DVD media kit"
(#C6N31A).
BD883A
HP Insight Management Media Kit
NOTE: HP Insight Management Media Kit contains DVDs without licenses. Contains HP
Systems Insight Manager, HP Insight Control, HP Matrix Operating Environment, and
Virtual Connect Enterprise Manager software. Uses an integrated installer to perform
quick and accurate software installation and updates.
C6N31A
NOTE: Licenses ship without media. The Insight Control Media Kit can be ordered
separately, or can be downloaded at: http://www.hp.com/go/insightupdates .
NOTE: The "for bundling with an enclosure" license kits can only be ordered together
with a BladeSystem c3000 or c7000 enclosure on the same order.
NOTE: Customer will receive a license entitlement certificate, which must be redeemed
online or via fax in order to obtain the license activation key(s). Includes one year of 24 x
7 HP Software Technical Support Service.
NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12631_na/12631_na.html
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 17

HP iLO Advanced for
BladeSystem License
HP iLO Advanced for BladeSystem including 1yr 24x7 Support Eight Server License 512489-B21
HP Virtual Connect
Enterprise Manager
HP Virtual Connect Enterprise Manager including 1yr 24x7 Support Single c3000
Enclosure Lic
NOTE: This license allows 1 BL-c3000 enclosure to be managed with VCEM. Customer
will receive a printed license entitlement certificate via physical shipment. The license
entitlement certificate must be redeemed online or via fax to obtain the license
activation key(s). Includes one year of 24 x 7 HP Software Technical Support and Update
Service.
459867-B21
NOTE: For additional License Kits, please visit:
http://h18000.www1.hp.com/products/quickspecs/12860_na/12860_na.html
HP c-Class Storage Blades HP D2200sb PCIe Storage Blade AP880A
NOTE: Please see the HP D2200sb Storage Blade QuickSpecs for technical specifications
and additional information at:
http://h18000.www1.hp.com/products/quickspecs/13714_na/13714_na.html
HP D2220sb PCIe and StoreVirtual VSA Bundle
NOTE: Includes the D2220sb Storage Blade and a single HP StoreVirtual VSA license.
VSA software is installed in a virtual machine on a VMware ESX/ESXi & Microsoft Hyper-
V host server adjacent to the D2220sb.
NOTE: Includes 3yr NBD Parts-Only Warranty Service for D2220sb hardware.
NOTE: Includes 3yr 9x5 remote technical support for HP StoreVirtual VSA software and
free updates.
NOTE: HP StoreVirtual VSA is supported on VMware ESX/ESXi & Microsoft Hyper-V.
QW914A
HP D2220sb PCIe w/(12) 900 GB 6G SAS HDD Bundle
NOTE: Includes 3yr NBD Parts-Only Warranty Service for D2220sb hardware
QW915A
HP D2220sb Build-to-order Storage Blade
NOTE: Includes 3yr NBD Parts-Only Warranty Service
QW917A
HP D2220sb Configure-to-order Storage Blade
NOTE: Includes 3yr NBD Parts-Only Warranty Service
QW918A
NOTE: The D2220sb requires a c7000 Enclosure configuration with 10 fans.
NOTE: Please see the HP D2220sb Storage Blade QuickSpecs for technical specifications
and additional information at:
http://h18000.www1.hp.com/products/quickspecs/14507_na/14507_na.html .
HP BL c-Class PCI Express Mezzanine Pass Thru Option Kit
NOTE: The HP PCI Express Mezzanine Pass-Thru Card (P/N 431643-B21) is required to
support an expansion blade with the ProLiant BL620c G7 Server Blade. Up to two
expansion blades are supported per server mix and match (Ultrium Tape,
D2220sb/D2220sb PCIe Storage, and/or PCI Expansion Blades). See the "Expansion
blade" section later in this document for more information.
431643-B21
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 18

HP Ultrium Tape Blades HP StoreEver LTO-5 Ultrium SB3000c Tape Blade BS580B
HP StoreEver LTO-4 Ultrium SB1760c Tape Blade AQ697B
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/12729_na/12729_na.html
HP BL c-Class PCI Express Mezzanine Pass Thru Option Kit 431643-B21
NOTE: The HP PCI Express Mezzanine Pass-Thru Card (P/N 431643-B21) is required to
support an expansion blade with the ProLiant BL620c G7 Server Blade. Up to two
expansion blades are supported per server mix and match (Ultrium Tape,
D2220sb/D2220sb PCIe Storage, and/or PCI Expansion Blades). See the "Expansion
blade" section later in this document for more information.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/12587_na/12587_na.html
HP Expansion Blade HP BLc PCI Expansion Blade 448018-B21
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/12753_na/12753_na.html
HP BL c-Class PCI Express Mezzanine Pass Thru Option Kit
NOTE: The HP PCI Express Mezzanine Pass-Thru Card (P/N 431643-B21) is required to
support an expansion blade with the ProLiant BL620c G7 Server Blade. Up to two
expansion blades are supported per server mix and match (Ultrium Tape,
D2220sb/D2220sb PCIe Storage, and/or PCI Expansion Blades). See the "Expansion
blade" section later in this document for more information.
431643-B21
HP Power Distribution
Units
NOTE: A pair of PDUs must be ordered for AC feed redundancy.
NOTE: Additional HP Power Distribution Units are available than those listed below. For
a complete list of all HP PDUs and additional information please visit:
www.hp.com/go/rackandpower .
Monitored PDU
HP Monitored Power Distribution Unit: Full Rack Version
HP 8.6kVA 24A Single Input Three Phase NA/JP Monitored Power Distribution Unit AF504A
HP 8.3kVA 40A Single Input Single Phase NA/JP Monitored Power Distribution Unit AF506A
HP Monitored Power Distribution Unit: Half Rack Version
HP 4.9kVA 24A Single Input Single Phase NA/JP Monitored Power Distribution Unit AF914A
NOTE: Please see the following QuickSpecs for additional information:
http://h18000.www1.hp.com/products/quickspecs/12118_na/12118_na.html
Modular PDUs
NOTE: Please see the following QuickSpecs for additional options including shorter
jumper cables and country specific power cords:
http://h18000.www1.hp.com/products/quickspecs/11041_na/11041_na.html
HP Two C13 PDU Extension Bar AF500A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information: www.hp.com/go/pdu
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 19

NOTE: Please see the UPS and PDU cable matrix's on the HP Power Protection and
Management page. Under Power Cords, click on the "HP Power Cord Matrix" link. That
link will list cable descriptions, requirements, and specifications for UPS and PDU units.
Please see the following link: www.hp.com/products/powercords .
HP Intelligent Power
Distribution Units (iPDU)
NOTE: A pair of PDUs must be ordered for AC feed redundancy.
NOTE: Additional HP Power Distribution Units are available than those listed below. For
a complete list of all HP PDUs and additional information please visit:
www.hp.com/go/rackandpower .
iPDU Core Units
HP 4.9kVA 24A Single Phase NA/JP Core Intelligent Modular Power Distribution Unit AF520A
HP 8.6kVA 24A Three Phase NA/JP Core Intelligent Modular Power Distribution Unit AF522A
iPDU Extension Bars
HP 5xC13 Intelligent PDU Extension Bar G2 Kit AF547A
HP 5xC13 Outlets Power and UID LEDs Pair Standard Extension Bar AF528A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/13650_na/13650_na.html
HP Uninterruptible Power
Systems
NOTE: A pair of PDUs must be ordered for AC feed redundancy.
NOTE: Additional HP Power Distribution Units are available than those listed below. For
a complete list of all HP PDUs and additional information please visit:
www.hp.com/go/rackandpower .
HP Rack-mountable UPS
HP R1500 G3 Uninterruptible Power Supply (UPS)
HP R/T3000 G2 2U L530 Low Voltage NA/JP Uninterruptible Power System AF466A
NOTE: Please see the QuickSpecs for additional information:
http://h18000.www1.hp.com/products/quickspecs/14059_na/14059_na.html
HP R/T3000 G2 Uninterruptible Power System (UPS)
HP R/T3000 G2 2U L620 High Voltage NA/JP Uninterruptible Power System AF467A
NOTE: Please see the QuickSpecs for additional information:
http://h18000.www1.hp.com/products/quickspecs/14058_na/14058_na.html
R5000 Uninterruptible Power System (UPS)
HP R5KVA 3U L630 High Voltage NA/JP Uninterruptible Power System AF460A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/14109_na/14109_na.html
R7000 Uninterruptible Power System (UPS)
HP R7KVA 4U 50A High Voltage NA/JP Uninterruptible Power System AF462A
HP R5KVA and R7KVA 3U Extended Runtime Module AF464A
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information at:
http://h18000.www1.hp.com/products/quickspecs/14110_na/14110_na.html
QuickSpecs
HP BladeSystem c3000 Enclosure
Related Options
DA - 12790 North America — Version 55 — December 10, 2013 Page 20