SMAI AIRFIT User manual

OWNER'S MANUAL

2
3-4
5
6-11
12-14
15-17
Table of Contents
Important Safety Information
Before You Start
Assembly Instruction
Console Instruction
Part List
Exploded View 18
IF you experience other technical problems that are not listed or have additional
question, please contact the original retailer or call us at
1-888-678-2476

3
Important Safety Information
WARNING! Before using this unit or starting any exercise program, consult your
physician. This is especially important for persons over the age of 35 and/or persons
with pre-existing health problems. The manufacturer or distributor assumes no
responsibility for personal injury or property damage sustained by or through the use
of this product.
SAFETY PRECAUTIONS AND TIPS
1. It is the owner's responsibility to ensure that all users of this unit have read the
Owner's Manual and are familiar with warnings and safety precautions.
2. This unit has a user maximum capacity of 300 pounds. (136 Kilograms)
3. The bike is NOT equipped with a freewheel system which means that when
the flywheel is in motion, the pedals will be in motion. Do not attempt to stop the
unit by applying backward pressure to pedals while they are turning as knee
injury may occur.
5. Do not attempt to turn the pedal cranks by hand. Do not touch any
driving mechanism while it is in motion as possible injury could occur.
6. In a home setting, keep children away from the bike when it is not in use. Keep
children and pets away from the unit while it is in use.
7. Do not attempt to perform dip movement on handlebars.
8. The unit should only be used on a level surface and is intended for indoor use
only. The unit should not be placed in a garage, patio, or near water and should
never be used while you are wet. We recommend a mat be placed under the unit
to protect floor or carpet and for easier cleaning.
9. Wear comfortable, good-quality walking or running shoes and appropriate
clothing. Do not use the unit with bare feet, sandals, socks or stockings.
10. Always examine your unit before using to ensure all parts are in working order.
11. Allow the unit to fully stop before dismounting.
12. Pets should never be allowed near the unit.

4
13. Do not leave children unsupervised near or on the unit.
14. Never operate the unit where oxygen is being administered, or where aerosol
products are being used.
15. Never insert any object or body parts into any opening.
16. For safety and to prevent damage to your unit, no more than one person
should use the unit at a time.
17. Service to your unit should only be performed by an authorized service
representative, unless authorized and/or instructed by the manufacturer.
18. Failure to follow these instructions will void the unit warranty.

5
Before You Start
Thank you for purchasing this new AIR BIKE! This quality product you have
chosen was designed to meet your needs for cardiovascular exercise. Before you
start, please read the Owner's Manual and become familiar with the operation of
your new unit.
Proper instal
safety. Maintenance is the sole responsibility of the owner.
Remembertotake the time to perform the stretching exercises provided to
avoid injury.
If you are taking medication, consult your physician to see if the medication will
affect your exercise heart rate.
If you have heart problems, you are not active, and/or are overthe age of 35
years, do not use the pre-set programs or start an exercise program without first
contacting and receiving approvalfrom your physician.
To avoid the risk of electrical shock, always keep the console dry. Do not spill
liquids on the console. We recommend a sealed water bottlefor beverages
consumed while using the unit.
Please review the following drawing below tofamiliarize yourself withthe listed parts.

6
REMOVE ALL SECURITY TAPE AND WRAPPING
BEFORE BEGINNING
Assembly Instruction
FIGURE 1 Stabilizers Assembly
STEP 1
Assemble the Front and Rear Stabilizers ( A06) &(A07) tothe Main Frame (A01)
withfour Flat Washers ( D03), four Spring Washer (D06) and four Screws (B06) as
show on the following picture.
NOTE:
1.) There are two Foot Adjusters (E10) on each Stabilizer (A06, A07). Adjust
these foot adjusters to make sure the bike is stably positioned on the ground
for exercise.
2.) Please be sure that the Stabilizers(A06. A07) are screwed firmly with Main Frame
(A01) before riding onto the bike.

$
7
Assembly Instruction
FIGURE 2 Right & Left Handlebars Assembly
Step 1
Install the Right Handlebar Assembly ( A02) onto U shape tube of the main frame
(A01) by threading the backside part of the the Foot Peg into the position A. Use
the provided wrench tool on the Foot Peg bolt to hand tighten (Image 1), then use
a hammer to lightlytap on the wrench totighten another quarter turn (Image 2).
This will provide correct torque setting.
Right Handlebar
Lower Povit
Right Handlebar
Assembly Position A
Foot Peg
Left Handlebar
Lower Povit
Foot Peg

8
Assembly Instruction
FIGURE 2 Right & Left Handlebars Assembly
Step 2
Assemble Right Handlebar Assembly (A02) with Right Linkage Arm (A05) per one
Screw (B14), two Washers (D01), the bearing (E16) of Linkage Arm and one
Nylon Nut (C02) as shown as below drawing.
Step 3
Repeat above procedure to assemble Left Handlebar Assembly (A03).
FIGURE
Right Handlebar Assembly Position A
Foot Peg
Right Handlebar Lower Povit
Left Handlebar Lower Povit
Foot Peg

9
Assembly Instruction
FIGURE 3 Right & Left Pedals Assembly
Step 1:
Thread the Right Pedal (G11) into the hole of Right Crank(E05). Secure in place
by turning it clockwise to tighten.
Note: Right Pedal (G11)is marked with an
Thread the Left Pedal (G10) into the hole of Left Crank(E04). Secure in place by
turning it
counterclockwise to tighten.
FIGURE 3
seat pad
locknut

10
Assembly Instruction
FIGURE 4 Monitor Assembly
Step 1
Use the wire which is attached tothe Console Mast (A11)totiethen lead the
Sensor Wire(Upper) (H04) from Main Frame (A01) to get through the Console
Mast (A11) till the top opening of Console Mast (A11)
Please note not to crush Sensor Wire(Upper) (H04) when assembling Console Mast
(A11) onto the Main Frame (A01) with two Screws ( B06) and two Washers ( D03)
as show as below picture.
Step 2
Well connect the Sensor Wire(Upper) (H04)tothe cable of Console (H01),
then fixthe Console (H01) onto the Console Mast (A11) per four Screws (B03).
Step 3
Insert Seat Post (A08)into Main Frame (A01), fixed by Pop Pin Knob (E09). Fix
Seat Pad (G12) on the Seat Post (A08). Seat Position can be adjusted from this
seat post tofit for your height.
FIGURE 4

$
11
Assembly Instruction
Congratulations!
You have completed the assembly of your new Air Bike!
Make sure all bolts, pedals, pop pin knobs are tightened for exercise!

12
Console Instruction
How to operate:
1st. Press Start key then press UP / DOWN key to set user's age, then press
ENTER to confirm.
2nd. Press Start key to start exercise for manual operation Or select program (7
programs) on the right side of console for exercise.
1. KEY FUNCTION :
● START : Press “ Start “ to standby Mode, then choose the desired program.
● STOP : Press “ Stop” for 1~2 secs will make working programs to temperately
pause, but press over 2 seconds will clear all your setting data and get back
to standby Mode.
● ENTER : Press “ Enter key “ to confirm all your desired values.
● UP & DOWN : Set your desired value by pressing UP or Down key.
Note : In standby mode, if no data is keyed in, console will be off automatically.
2. INTERVAL DISPLAY
Interval Display Panel
Program :
(1) Interval 20/10(Work:20 Seconds,Rest:10
Seconds)
(2) Interval 10/ 20 (Work:10 Seconds,Rest:20
Seconds)
(3) Interval Custom
The above three programs all display on this
Interval Display Panel.
(A) The upper banner -- will signal which interval program is running and tell you the currently
running interval is a Work or Rest period. ( Program (1) and (2) -Work and Rest interval are

13
preset for 8 circles, while the program (3) is 1circle preset).
(B) The Total Time display -- will count up the total program run time while the large numeric
display will count up the Work or Rest segment time.
(C) The 88/88 Display -- will show the current interval and the total number of intervals in the
program.
3. TARGET TIME, DISTANCE & CALORIES DISPLAY
Program: (4) Target Time (5) Target Distance (6) Target
Calories, three programs all display on this Target Display
Panel.
(A) A top banner shown as right diagram-- will signify
which target program is running.
(B) The time display-- will alternate between the remaining
and elapsed values throughout the program.
(C) Total distance --will be displayed in miles or kilometers
depending upon how the console was programed during the initial setup.
(D) The Calories display --will track the number of calories burned during the workout.
4. WATTS/ SPEED / RPM DISPLAY
Regular display : Watt, Speed, RPM
--The above will be displayed for all programs.
Watt: A measurement of energy generation and will track the amount of work generated at any
given time during a workout.
Speed display :will post a value which simulate that of riding a standard bicycle and is derivative of
the current RPM or pedal speed.
RPM: relates to the speed at which the cranks are spinning
(A) Under active situation :Watts, Speed and RPM will offer currently active value.
(B) Under pause mode or stop situation : Watt, Speed and RPM display will show the max
value, summarized value, average value
5. HEART RATE DISPLAY
Heart Rate Display panel
Program : Target Heart Rate
This console is implanted wireless receiver, so pulse can be
read per wearing wireless pulse belt ( optional accessory)
When user’s pulse is detected by console, it will display
current heart rate value in the large, three-digiit BPM (
beats-per-minute) filed and Heart icon will flash. There is BPM range control, from 65% of Max
HR to 80% of Max HR. Your target heart rate vaule will bring out the BPM range, and SPEED
BANNER ( increase or decrease ) will signal you to speed up or slow down when you are not in

14
the BPM range. When the user’s heart rate is within the target range, the Target Heart Rate
Achieved banner will post.
To calculate your maximum heart rate and find the appropriate target training zone,use the
following formulas. The following estimation would be relevant for a 35 year-old user.
220 - 35 = 185 BPM (220-Age=Calculated MaximumHeartRatein BPM)
0.65 x 185= 120 BPM (65% of 185 BPM [Calculated MaximumHeart Rate]=120 BPM)
0.80 x 185 = 148 BPM (80% of 185 BPM [Calculated Maximum Heart Rate]=148 BPM)
6. ADDITIONAL INFORMATION:
(A) In any condition, pressing “ stop “ key for over 2 seconds will reset this console.
(B) In standby mode, no key press for over 30 seconds will enter into sleep mode .
(C) The console will be active if any key is pressed in the sleep mode.
(D) 1 minute only for Pause mode,, after 1 min the console will enter into sleep mode, usercan
press “ start “ mode to start the training again.
(E) Once stop pedaling and console did not sense RPM for over 1 min, the console will enter into
sleep mode automatically.
(F) To switch KM and ML, please press Start key and Enter key simultaneously, then press UP
or DOWN to choose then press Enter to confirm.

15
PART LIST
ITEM
PART NAME
QTY
A01
Main Frame
1
A02
Right Handle Bar
1
A03
Left Handle Bar
1
A04
Chain Transmission Axle
1
A05
Linkage Arm
2
A06
Front Stabilizer
1
A07
Rear Stabilizer
1
A08
Seat Post
1
A09
Seat Post Slider
1
A10
Fan Steel Bracket Set
1
A11
Console Mast
1
A12
Fan Netting fixed plate
7
A13
*None*
*
B01
10x16x17mm Screw
7
B02
TP4x16L Screw (black)
1
B03
M5x10L Phillips Screw
4
B04
M5xP0.8x8L Phillips Screw (black)
7
B05
M5xP0.8x8L Phillips Screw (stainless)
1
B06
M8x20L Hex Round Head Screw (DIA 6mm)
6
B07
M8x45L Hex Round Head Screw (carbon)
2
B08
M22 x17x91.4 Hex Head Screw
2
B09
M6x12L Hex Head Screw (Loctite, silver)
4
B10
M6x16L Hex Head Screw (carbon , silver)
4
B11
M6x6L Hex Round Head Screw (black)
2
B12
Crank Fixing Bolt
3
B13
M6xP1.0x15L Socket Head Screw
4
B14
M10x40 Hex Flat Head Screw
2
B15
*None*
*
B16
*None*
*
C01
3/8x26” Acorn Nut Cap
4
C02
M10 Nylon Nut (thin) (black)
2
C03
M14xP1.5 , R Locknut (Loctite)
2
C04
M6 Hex Nut (Black)
4
C05
M6 Nylon Nut (silver)
4
C06
M8 Nylon Nut (thick)
2
C07
* None*
*
C08
M10 HEX NUT (thin) (black)
2
D01
10x19x2.0t Washer (black)
4

16
D02
16x21.8x2.0t Washer ( black)
2
D03
8x19x1.0t Washer (black)
10
D04
5x1t Spring Washer (black)
7
D05
6x1t Spring Washer (black)
12
D06
8x2t Spring Washer (black)
4
D07
* None *
*
D08
16x21.8x1.0t Washer ( black)
2
D09
Ø 26* Ø 20*1.0m/m Washer(stainless)
5
D10
Ø 21* Ø 16*0.3m/m Washer(stainless)
2
E01
Foot Peg (38.4x32x110.6mm)
2
E02
Crank Fixed Round Plate (L)
1
E03
Crank Fixed Round Plate( R)
1
E04
Left Crank
1
E05
Right Crank
1
E06
Seat Fixing Rod
1
E07
C Retainer ( S-20)
1
E08
Adjustment Channel
4
E09
Pop Pin Knob
2
E10
Foot Adjuster
4
E11
Chain Tensioner
4
E12
#6004 Precise Bearing
2
E13
#6803 Precise Bearing
8
E14
#99502ZZ Ball Bearing
2
E15
Cir –Clip
4
E16
POS10 Bearing (M10x1.5)
2
E17
Inner Lock Tablet (ψ23*ψ9*23L)
1
E18
Inner Lock Tablet (ψ23*ψ9*37.5L)
1
E19
Front Chain Wheel
1
E20
*None*
*
E21
*None*
*
E22
Rear Chain Wheel
1
F01
Chain Guard (Left)
1
F02
Chain Guard (Right )
1
F03
Fan Cage (Left )
1
F04
Fan Cage (Right )
1
G01
Transportation Wheel
2
G02
Seat Post Support Bushing
1
G03
DIA 50 Hex End Plug
2
G04
Seat Fixed Hex Spacer
1
G05
DIA38 Hex End Plug
2
G06
Handlebar Sleeve
2
G07
V-Belt
1

17
G08
Fan Cage Cover (Left )
1
G09
Fan Cage Cover (Right )
1
G10
Left Pedal
1
G11
Right Pedal
1
G12
Seat Pad
1
G13
Stabilizer End Cap
4
G14
*None*
*
G15
*None*
*
G16
Steel Chain
1
G17
*None*
*
G18
*None*
*
G19
Wire Plug
2
H01
Console
1
H02
Sensor Wire(Lower) with Sensor
1
H03
Magnet
1
H04
Sensor Wire (Upper)
1

-18-
Assembly Instruction