Orbit R400 User manual

-0-

KIT TOOL & SCREW SET - List
(Pedal Wrench)
Allen Key(1)
Screwdriver (1)
R400
I-3 Screw M5*12 (8)
I-2 Curved washer for ? 8*? 19*2T bolt(8)
I-1 Allen Bolt M8x16mm
I-4 Screw M5*10 (4)

-2-
Assembly Instruction

-3-
Step 1
1. Attach the Rear Support (N) with Slippery Rail (M-L,M-R) and secure the Rear Support with
M8xP1.25x20L Bolt (N-5),Curved Washers (N-4) and Carry Bar (N-3).
Step 2
1. Attach Seat (K-1) onto the Rolling Slider ( K) with M8*16mm Allen Bolt (I-1) and Curved Washers (I-2)

-4-
Step 3
1. Slide the Seat (K) onto the Slippery Rail (M-l , M-R).
Step 4
1. Attach the Pedal with band (J-3 & J-5 ) ,then attach onto the pedal support ( J ) with Screws (I-3).

-5-

-6-
Step 5
1.Please pay special attention to this step. Hole size on slippery rails are larger than bolt size, when
assembling the pedal holder (J) with the slippery rail using I-1 bolts, please do not fasten the bolts
until it's tested that the slippery rails are parallel and the saddle can move smoothly along the
rails"
Step 6
1. Attach the Rear Cover (N-6) onto the Rear Support with Screw (I-4).

-7-
Step 7
1.Attach the Slippery Rail (M-l , M-R) with the Main Frame (D) by using M8*16mm Allen Bolt (D-13) and
Curved Washers (D-14).
2. Finally, attach the Cover (D-15) onto the Main frame (D) with M5x10L Washer (D-16).

Explosion Drawing

Parts List ROWER MACHINE
No.
Description
Quantity
A
COMPUTER
1
SET
A-1
SCREW FOR FIXING COMPUTER
4
PCS
B
SUPPORTING TUBE FOR BRACKET
1
PCS
B-1
BRACKET FOR FIXING COMPUTER
1
PCS
B-2
SCREW
2
PCS
B-3
FIXING CAP
4
PCS
B-4
CURVED WASHER φ6xφ16x1t
2
PCS
B-5
NYLON NUT M6
2
PCS
B-6
HEXAGONAL SCREW M6xP1.0x57L
1
PCS
C
BRACKET FOR ROLLER
1
SET
C-1
DRIVING PULLEY
1
SET
C-2
ROLLER
1
SET
C-3
SCREW M6x50L
1
PCS
C-4
SCREW
1
PCS
C-5
NYLON NUT 3/8"x7t
1
PCS
C-6
NYLON NUT M6
1
PCS
C-7
SCREW M8xP1.25x35L(6m/m)
2
PCS
C-8
CURVED WASHER φ8*φ19*2T
2
PCS
C-9
BUSHING φ10xφ14x6mmL
2
PCS
C-10
BUSHING φ6xφ8.5x3mmL
4
PCS
C-11
CURVED WASHER φ6xφ16x1t
1
PCS
C-12
CURVED WASHER φ10xφ18x1t
1
PCS
D
MAINFRAME
1
SET
D-1
CAP FOR FRONT STABLILZER(LEFT)
1
PCS
D-2
CAP FOR FRONT STABLILZER(RIGHT)
1
PCS
D-3
SUPPORTING CAP(LEFT)
1
PCS
D-4
SUPPORTING CAP(RIGHT)
1
PCS
D-5
ADJUSTING CAP
2
PCS
D-6
HEXAGONAL SCREW 3/8"-16x3t
2
PCS
D-7
TRANSPORATION
2
PCS
D-8
C-TYPE RING φ8
2
PCS
D-9
SPEEDY NUT M8
2
PCS
D-10
SENSOR BOX
2
SET
D-11
SCREW M4x10L
2
PCS
D-12
GEAR BOX
1
PCS
D-13
ALLEN BOLT M8*16mm
8
PCS
D-14
Curved WASHER φ8*φ19*2T
8
PCS
D-15
FRONT CAP FOR SLIDER
1
PCS
D-16
SCREW M5x10L
8
PCS
D-17L
LEFT COVER(LOWER)
1
PCS
D-17R
RIGHT COVER(LOWER)
1
PCS
D-18
SCREW 3/16"（#10）x3/4"
2
PCS
D-19
SCREW M4x50L
3
PCS
D-20L
SIDE COVER(LEFT)
1
PCS
D-20R
SIDE COVER(RIGHT)
1
PCS