SMARDY PRO 190 User manual

Reverse Osmosis system 50 GPD
Instruction manual EN

Contents
1. Unpacking
2. Scope of supply
3. Insertion of the membranes
4. Connecting the lines
5. Installation
6. First commissioning
7. Consumables
8. Technical data
9. Assembly and instructions
10. Filter change
11. Filter order
1. Unpacking
Remove all packaging material. Make sure that the reverse osmosis system does not
show any external damage.
2. Scope of supply
1. smardy reverse osmosis water filter
2. Storage tank 11,35L
3. Water tap
4. Hose line
5. VOTRON Membrane
6. Key for membrane housing
7. Angle valve connection adapter 3/8” x 3/8” + stopcock
8. Clamp for waste water
9. Teflon tape
10. Stopcock storage tank
11. Fixing material

Note:
This system is equipped with plug connectors. These enable an easy and secure
connection of the hose lines. Insert the hose into the respective opening of the
connector until you notice a resistance. Only after the resistance, the hose will be
fixed in the anchor.
•In order to be able to remove the
hose again, you will first have to
remove the safety clamp
•On the connector you will see a small
white plastic ring. Push it evenly in
the direction of the connector and
simultaneously pull the hose.
3. Insertion of the membranes
•Remove the hose from the membrane housing.
•Unscrew the cover from the membrane housing.
(Tool: Key for membrane housing)
•Then first insert the membrane with the two black rubber rings
into the housing.
•Insert the membrane into the housing up to the stop.
•Srew the cover back on to the membrane housing.
•Insert the hose back into connector.

4. Connecting the lines
•Please connect hose lines as follows:
Remove the blue retaining rings from the plug connectors at the
Water inlet connection tank Waste water and Osmosis water
•Now insert the hoses into the connectors.
•Fasten the blue retaining rings back onto the connectors
Water inlet
Connection tank
Waste water
Connection:
water armature
•The scope of supply includes 1 roll of hose, please cut it to the appropiate length.

5. Installation
•The scope of supply includes a connector for the water supply as well as the
corresponding stopcock.
•Close the water supply on your angle valve and unscrew the cold water pipe. Then
screw the connector for the water supply onto the angle valve.
•Place 9 to 10 layers of teflon tape around the thread of the stopcock.
Then screw the stopcock into the lateral screw opening of the water connection
component.
•On the other side of the connector for the water supply, screw the cold water pipe
back on.
•Now remove the nut from the cockstop and put it over the white hose, which
supplies the osmosis system with tap water.
•Then put the white hose onto the stopcock, the hose has to be put over the
protruding ring.
•Screw the nut back onto the stopcock.
Connect the line with the system
Cold water pipe
Stopcock
Connection water supply
Angle valve

Installation of the water armature:
•Drill a 12 mm hole through the sink.
1. Put the cover over the threaded rod of the
water tap.
2. Put the threaded rod through the drilled
hole in the kitchen countertop.
3. Slide the locking washer from underneath
over the threaded rod.
4. Now slide the snap ring onto the threaded
rod.
5. Screw the lock nut onto the threaded rod
and screw down the water tap.
6. Then take the blue hose and put the nut
over the hose.
7. Take the sleeve and put it onto the hose.
8. Subsequently take the insert sleeve and
stick it into the hose.
9. Now insert the hose into the inner
line of the threaded rod and then screw
the nut onto the threaded rod.

Water Inlet
Determine the assembly site for the waste water clamp. This one must absolutely be
positioned over the syphon bend. (the area is marked here in green)
•Drill a hole in the syphon with a 6mm drill bit.
•Stick the foam seal around the drilled hole.
•Fasten the clamp (tighten both screws uniformly).
•Cut the required length off the hose.
•Put the nut over the hose.
•Push the hose into the opening of the clamp.
•Screw the nut and the clamp together.
•Connect the hose with the plug connection❸
Installation storage tank

6. First commissioning
Before you open the water supply, please double-check all the hose lines.
These must have been laid absolutely free of kinks.
•Open the filter flush valve. It is located before the membrane.
•Open the water supply (shown here in the green circle) and check all the
connections for tightness.
•Leave the filter flush valve in an open position for approx. 10 minutes.
•Close the filter flush valve.
•Open the water tap for 5 min to flush all the lines once again.
•Subsequently you can enjoy fresh osmosis water

8. Technical data
•Dimensions: 29cm x 24cm 46cm (LxBxH)
•Daily filter performance: 190 Liter
•Water purification without electricity–only 3 bar tap water pressure required
9. Assembly and instructions
•We recommend, to let an installer perform the installation. Incorrect assembly can
lead to water damage in the house!
•The connecting parts are tested and standards compliant. Should you wish to obtain
other connecting parts, you can acquire them from us, or from any installation
specialist shop.
•The installation instructions are implementing recommendations for a standard
connection. Local regulations for installation and building standards can contain
other or additional requirements.
•The executing installer is responsible for the compliance with applicable rules.
7. Consumables
For your system you need the following replacement filters and membranes:
item N°
Description
Change interval
Daily output
190 L
N° 8
Membrane 50 GPD
Every 24 months
N° 9
Activated carbon afterfilter
Every 12 months
N° 11
Sediment filter
Every 6 months
N° 12
Activated carbon block filter
Every 6 months
N° 13
Activated carbon sediment
filter
Every 6 months
Just smardy original filters ensure a trouble-free functioning!!

10. Filter change
Recommended change interval
N° 8 12 -24 months
N° 9 12 months
N° 11 6 months
N° 12 6 Monate
N° 13 6 Monate
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter
Date:
oN° 8 Membrane 50 GPD
oN° 9 Activated carbon afterfilter
oN° 11 Sediment filter
oN° 12 Activated carbon block filter
oN° 13 Activated carbon sediment filter

11 Filter order

smardy©
Robert-Bosch-Str. 6b
86830 Schwabmünchen
Germany
[email protected]
Link for accessories:
https://www.amazon.co.uk/dp/B06XZYFL5C