SMARDY UF 2000 User manual

Ultrafiltration system
Instruction manual EN
Contents
1. Unpacking
2. Scope of supply
3. Insertion of the membrane
4. Connecting the lines
5. Installation
6. Technical data
7. Fist commisioning
8. Consumables
9. Filter change
10. Filter change
11. Filter order

Note:
This system is equipped with plug connectors. These enable an easy and secure
connection of the hose lines. Insert the hose into the respective opening of the
connector until you notice a resistance. Only after the resistance, the hose will be
fixed in the anchor.
•In order to be able to remove the
hose again, you will first have to
remove the safety clamp
•On the connector you will see a small
white plastic ring. Push it evenly in
the direction of the connector and
simultaneously pull the hose.
1. Unpacking
Remove all packaging material. Make sure that the reverse osmosis system does not
show any external damage.
2. Scope of supply
1. smardy UF 2000
2. Water tap
3. Key for membrane housing
4. Hose line
5. Ultrafiltration membrane
6. Angle valve connection adapter 3/8”
x 3/8” + stopcock
7. Key for filter housing
8. Fixing material
9. Teflon tape

4. Connecting the lines
•Please connect hose lines as follows:
Remove the blue retaining rings from the plug connectors at the
Water inlet rinsing water drainage
and Water armature connector
•Now insert the hoses into the connectors.
•Fasten the blue retaining rings back onto the connectors
3. Insertion of the membranes
•Remove the hose from the membrane housing.
•Unscrew the cover from the membrane housing.
(Tool: Key for membrane housing)
•Then first insert the membrane the housing up to the stop
•Srew the cover back on to the membrane housing.
•Insert the hose back into connector.
•Insert filters 4, 5 and 6. (Tool: key for filter housing
Water inlet
Membrane flush
valve
Rinsing water
drainage
Water armature
connector
The scope of supply includes 1 roll of hose, please cut it to the appropiate length

5. Installation
•The scope of supply includes a connector for the water supply as well as the
corresponding stopcock.
•Close the water supply on your angle valve and unscrew the cold water pipe. Then
screw the connector for the water supply onto the angle valve.
•Place 9 to 10 layers of teflon tape around the thread of the stopcock.
Then screw the stopcock into the lateral screw opening of the water connection
component.
•On the other side of the connector for the water supply, screw the cold water pipe
back on.
•Now remove the nut from the cockstop and put it over the white hose, which
supplies the osmosis system with tap water.
•Then put the white hose onto the stopcock, the hose has to be put over the
protruding ring.
•Screw the nut back onto the stopcock.
Connect the line with the system
Cold water pipe
Stopcock
Connection water supply
Angle valve

Installation of the water armature:
•Drill a 12 mm hole through the sink.
1. Put the cover over the threaded rod of the
water tap.
2. Put the threaded rod through the drilled
hole in the kitchen countertop.
3. Slide the locking washer from underneath
over the threaded rod.
4. Now slide the snap ring onto the threaded
rod.
5. Screw the lock nut onto the threaded rod
and screw down the water tap.
6. Then take the blue hose and put the nut
over the hose.
7. Take the sleeve and put it onto the hose.
8. Subsequently take the insert sleeve and
stick it into the hose.
9. Now insert the hose into the inner
line of the threaded rod and then screw
the nut onto the threaded rod.
6. Technical data
•Dimensions: 40cm x 13cm 43cm (LxWxH)
•Daily filter performance: up to 2000 liters
•Water purification without electricity–only 3 bar tap water pressure required

•Open the filter flush valve. It is located before the membrane.
•Open the water supply (shown here in the green circle) and check all the
connections for tightness.
•Leave the filter flush valve in an open position for approx. 10 minutes.
•Close the filter flush valve.
•Open the water tap for 5 min to flush all the lines once again.
•Subsequently you can enjoy fresh osmosis water
•After the last daily use of the filters, the shut-off-valve ( ) should be closed to
protect the system against nocturnal pressure surges.
7. First commissioning
Before you open the water supply, please double-check all the hose lines.
These must have been laid absolutely free of kinks.
8. Consumables
For your system you need the following replacement filters and membranes:
item N°
Description
Change interval
Daily output
up to 2000 L
N° 4
Activated carbon block filter
Every 6 months
N° 5
Granular carbon filter
Every 6 months
N° 6
Sediment filter
Every 6 months
N° 9
Activated carbon afterfilter
Every 12 months
N° 10
Ultrafilter membrane
Every 24 months
Just smardy original filters ensure a trouble-free functioning!!
Membran flush valve

9. Assembly and instructions
•We recommend, to let an installer perform the installation. Incorrect assembly can
lead to water damage in the house!
•The connecting parts are tested and standards compliant. Should you wish to obtain
other connecting parts, you can acquire them from us, or from any installation
specialist shop.
•The installation instructions are implementing recommendations for a standard
connection. Local regulations for installation and building standards can contain
other or additional requirements.
•The executing installer is responsible for the compliance with applicable rules.
10. Filter change
Recommended change interval
N° 4 6 months
N° 5 6 months
N° 6 6 months
N° 9 12 months
N° 10 24 months
Date:
oN° 4 Activated carbon block filter
oN° 5 granular carbon filter
oN° 6 Sediment filter
oN° 9 Activated carbon afterfilter
oN° 10 Ultrafilter membrane
Date:
oN° 4 Activated carbon block filter
oN° 5 granular carbon filter
oN° 6 Sediment filter
oN° 9 Activated carbon afterfilter
oN° 10 Ultrafilter membrane
Date:
oN° 4 Activated carbon block filter
oN° 5 granular carbon filter
oN° 6 Sediment filter
oN° 9 Activated carbon afterfilter
oN° 10 Ultrafilter membrane
Date:
oN° 4 Activated carbon block filter
oN° 5 granular carbon filter
oN° 6 Sediment filter
oN° 9 Activated carbon afterfilter
oN° 10 Ultrafilter membrane

11 Filter order
smardy©
Robert-Bosch-Str. 6b
86830 Schwabmünchen
Germany
[email protected]
Link for accessories:
https://www.amazon.co.uk/dp/B06Y16H1NM