Smart Solar Prism Solar Motion Light User manual

[email protected] www.smartlivinghg.com
Prism Solar Motion Light
Smart Solar is a Smart Living Home & Garden brand. © 2021 V0 #SmartLivingHG
This solar light works by using energy generated by the solar panel during the day to charge the internal
rechargeable battery which is used to power the light at night. When in 1 of the 3 on modes it will automatically
illuminate at night by using a light sensor and motion sensor. The number of times it can illuminate at night will
depend of which mode you have it set to and how much charge the battery received during the day.
The motion sensor has a detection field of 120 degrees wide and a range of 10-15 feet away so make sure to
take that into account when choosing a location.
Battery already installed inside light.
You can mount the light in a variety of locations such
as a wall, deck, shed, fence, post, etc. After you find
a good place to install the light you can attach it using
the screws provided through the holes in the top of
the light. Based on the material, to you can use the
walll anchors if needed.
Solar Panel with Light Sensor
Motion Sensor
On/Off/Mode Button
Screws x2
Anchors x2
Day: Install in a location where the solar panel
can receive the maximum amount of direct sun.
Light coming through trees, screens, or windows
is not considered direct.
Night: Do not install near another light as it
may interfere with the light sensor and prevent
the light from working properly at night.
Introduction
Installation
Contents
Position

[email protected] www.smartlivinghg.com
Prism Solar Motion Light
Smart Solar is a Smart Living Home & Garden brand. © 2021 V0 #SmartLivingHG
Press the button under the sensor to turn the unit on. It blinks once to let you know it is in mode 1. Press
the button a 2nd time and it blinks twice to let you know it is in mode 2. Press the button a 3rd time and
light blinks 3 times to let you know it is in mode 3. Press the button a 4th time to turn it off. In all 3 modes
the unit uses a light sensor in the solar panel to stay off during the day and work automatically at night
when dark enough.
As rechargeable batteries get older and go through more charge/discharge cycles they become less
efficient and the capacity reduces. If you find that the performance of the battery seems to be reduced
try boost charging the battery by turning it off to charge for 2-3 sunny days. If that does not improve the
performance you can replace the battery with one of the same specs.
Rechargeable Li-Ion (Lithium-Ion) battery size 18650, 3.7v, 1500mAh.
To replace the battery remove the screws
on the back of the unit . The battery
compartment is wired to the back cover.
Carefully pry the unit open so you do not
detach any wires. Remove the battery and
install a new one of the same specs. Then
screw the unit back together.
We recommend leaving it switched off for 2 sunny days to ensure the
battery is fully charged before first use. Once charged press the on button
to select the desired mode and your light with work automatically at night
using a built in light sensor.
Mode 1: light off, when motion is detected it illuminates on high brightness for 60 seconds
Mode 2: light stays on low, when motion is detected it illuminates on high for 60 seconds then returns to low
Mode 3: light stays on medium brightness all night, motion detector not active
Operation:
Battery:
Change Battery:
First Use:
<50%
48h
100%
1. Make sure the unit receives direct sun on the panel during the day. Move to a different location if needed.
2. Ensure you don’t have any lights shining on it at night that will interfere with the light sensor.
3. Press the on button and count the flashes to check which mode you selected.
4. Clean the solar panel and motion sensor with soft cloth and glass cleaner.
5. Replace the battery if needed.
6. If you replace the battery make sure to use the proper type and install correctly.
7. Check to see if any water has gotten into the light.
Troubleshooting
Back (Outside)
Back
(Inside)
Battery
Front
(Inside)