Smartwares 281517 Technical specifications

IP SURVEILLANCE CAMERA
IAN 281517
IP-ÜBERWACHUNGSKAMERA
Montage-, Bedienungs- und Sicherheitshinweise
105x148mm
Version 1.5
MONITOROVACIA IP KAMERA
Pokyny pre montáž, obsluhu a bezpečnostné
pokyny
BEZPEČNOSTNÍ IP KAMERA
Pokyny k montáži, obsluze a bezpečnostní pokyny
IP SURVEILLANCE CAMERA
Assembly, operating and safety instructions
IP ELLENŐRZŐ KAMERA
Szerelési, használati és biztonsági tudnivalók

GB Assembly, operating and safety instructions Page 5
HU Szerelési, használati és biztonsági tudnivalók Oldal 25
CZ Pokyny k montáži, obsluze a bezpečnostní pokyny Strana 47
SK Pokyny pre montáž, obsluhu a bezpečnostné pokyny Strana 67
DE/AT/CH Montage-, Bedienungs- und Sicherheitshinweise Seite 87
Before reading, unfold both pages containing illustrations and familiarise yourself with all
functions of the device.
Olvasás előtt kattintson az ábrákat tartalmazó mindkét oldalra és végezetül ismerje meg a
készülék mindegyik funkcióját.
Před čtením si odklopte obě dvě strany s obrázky a potom se seznamte se všemi funkcemi
přístroje.
Pred čítaním si odklopte obidve strany s obrázkami a potom sa oboznámte so všetkými
funkciami prístroja.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie
sich anschließend mit allen Funktionen des Gerätes vertraut.
100x148mm

5GB
List of pictograms used............................................ Page 6
Introduction....................................................................... Page 7
Intended use............................................................................ Page 7
Parts Description...................................................................... Page 8
Technical Data ........................................................................ Page 8
Scope of delivery.................................................................... Page 9
Safety instructions....................................................... Page 10
Trademark notices....................................................... Page 13
Installing the camera................................................. Page 13
Connecting the camera .......................................................... Page 15
Camera setup.......................................................................... Page 16
Changing passwords and configuring the camera on
the WLAN network................................................................. Page 17
Using the camera.................................................................... Page 18
Troubleshooting ............................................................ Page 20
Cleaning and Care....................................................... Page 21
Disposal................................................................................ Page 21
Warranty and Service.............................................. Page 22
Warranty Declaration............................................................. Page 22
Service address....................................................................... Page 22
Notes on Conformity................................................. Page 23

6 GB
List of pictograms used
Read the instructions!
Safety instructions
Directions for use
Dust- and hose-proof
DANGER: This symbol with wording "DANGER" indicates
a hazard which may result in
serious injuries or death if
not observed
. To avoid the da nger, follow the instruction.
WARNING: This symbol with the wording "WARNING"
indicates a hazard which may result in injuries or property
damage if not observed. To avoid the danger, follow the
instruction.
Keep out of reach of children!
Dispose of the packaging and the product in an environ-
mentally compatible manner!

7GB
IP Surveillance Camera
Introduction
Congratulations on the purchase of your new product. In
doing so you have chosen a top-quality product. Familiarise
yourself with the product before using it for the first time. Care-
fully read the following instructions for use with installation, operating
and safety information. The product also includes a tutorial CD provid-
ing more information on the special function of the camera, including
connecting it to a PC. Only use the product as indicated and for the
specified areas of application. Both instructions for use (Quick start
guide, instructional CD and instructions for use) are part of this product.
Keep these for future reference. If you pass the product on to anyone
else, please be sure to also include all documentation.
Intended use
This camera fall into the category information technology. The product
is suitable for use indoors or in protected outdoor areas and is for the
surveillance of garages, car parks, house entrances, etc. This camera
features a night vision function with 6 infrared LEDs for a clear image
in the dark. It also features a built-in Mikrophone for recording ambi-
ent noise. Transmission is sent to a router, from where it can be ac-
cessed and controlled via app. Any use other than previously described or
modifying the product is prohibited and will result in damage. The
manufacturer is not liable for any damages caused by improper use.
This product is not intended for commercial use.

8 GB
Parts Description
Before reading, unfold the page containing the illustrations and famil-
iarise yourself with all functions of the device.
1Camera
2Mounting bracket
3WLAN aerial
4Tutorial CD
5Wall plug (ø 5 mm)
6Screws
7Power supply
8Ethernet cable (see Fig. B)
9RJ-45 connection element
10 RESET button (see Fig. B)
11 SD slot (for Mikro SD card max. 32GB Class 10 - not included)
(see Fig. B)
12 Quick start guide
13 Decal for marking the area under surveillance
14 Installation, operating and safety information
Technical Data
Camera:
Device type: Surveillance Camera WLAN Outdoor
IP66
Dimensions: approx. 6 x 11cm (ø x d), approx.
6 x 15.5cm (ø x d) (with WLAN aerial
and sun screen)
Image sensor: 2 megapixel CMOS
Focal length: 3.6mm

9GB
Resolution (horizontal TV lines): 1280 x 720 pixel
Picture angle: H 60°, V 43° + /-5 °
Detection range
Motion detector: 90° x 5m
Infrared range (night vision
mode black/white): 6 IR LEDs up to 8m range
Operating temperature: -10°C – +50°C
Humidity during use: 40–80% RH
Storage temperature: -10°C – ~+60 °C
Humidity during storage: 20–90% RH
Connections: Ethernet (10/ 100 Base-T/ Base-TX);
WLAN IEEE 802.11b/ g/ n
Frequency: 2.4 GHz
Protection class: IP66 (dust- and hose-proof)
Weight: approx. 540g (camera with base,
aerial and sun screen)
Cable length: 0.66cm
Power supply (for dry indoor use only):
Model/type: KSAS7R50500150HE
Manufacturer: Kuantech (Beihai) Co., Ltd
Input voltage/frequency: 100–240V~, 50 /60 Hz
Input current: 0.25A
Output voltage: 5V DC
Output current: 1.5A
Protection class: II/
Scope of delivery
Remove all parts from packaging and dispose of all packaging material.
Please contact customer service if parts are missing or damaged.

10 GB
1 Camera
1 Mounting bracket
1 WLAN aerial
1 Power supply
1 Mounting kit
1 Tutorial CD
1 RJ-45 connection element
2 Decals for marking the area under surveillance
1 Quick start guide
1 Instructions for use
Safety instructions
Damage due to failure to comply with these instructions for use will
void the warranty! We assume no liability for consequential damage!
We assume no liability for property damage or personal injury due to
improper handling or failure to observe the safety notices!
Children and persons with limitations
DANGER TO LIFE AND RISK
OF ACCIDENT FOR INFANTS AND CHILDREN!
Never leave children unsupervised with the packaging
material. The packaging material poses a suffocation hazard. Pack-
aging materials are not toys. Children frequently underestimate the
dangers.
Always keep children away from the product. This device may be
used by children aged 8 years and up, as well as by persons with
reduced physical, sensory or mental capacities, or lacking experi-
ence and/or knowledge, when supervised or instructed in the
safe use of the device and they understand the associated risks.

11GB
Do not allow children to play with the device. Cleaning and user
maintenance must not be performed by children without supervision.
DANGER TO LIFE! During installation keep children away from
the area in which you are working. A large number of screws and
other small parts are included within the scope of delivery. These
may prove life-threatening if swallowed or inhaled.
Damage
Never use the product if it is damaged in any way.
Contact your service centre or a professional if the product is dam-
aged, requires repairs, or for any other problems with the product.
Ensure all electrical connections and cable connections to other
devices comply with the applicable guidelines and with the instruc-
tions for use.
Be sure not to overload socket and extension cables. This can lead
to fire or electric shock.
Please note the temperature and humidity during operation and
storage to ensure proper camera operation. These are specified in
the technical data. Moist, very cold or hot environments or storage
can damage the camera.
The camera is suitable for outdoor use, the power supply may only
be used indoors.
Avoid major shock. This can damage the electronic circuit.
Cordless systems are exposed to interference of telephones,
Mikrowaves, as well as other electronic devices operating in the
2.4 GHz range (impacts of interference include poor image quality
or transmission problems).
Maintain a minimum distance of 3 metres during installation and
operation.
Do not open the camera. This is a maintenance-free camera. Open-
ing the product will void the warranty.
Be sure not to damage any wires during installation.

12 GB
AC Adaptor
If defective, the power supply must be replaced with an identical
or equivalent type (identical electrical supply data).
Only plug the power supply into easy to access sockets so it can
easily be unplugged in the event of an emergency.
Do not touch the power supply with wet hands. Otherwise there is
a risk of electric shock.
Only use the power supply in dry indoor spaces.
Never unplug the device by the cable. Always touch the device by
the housing.
Please remember the power supply will continue to draw a small
amount of electricity even without the camera being operated so
long as the power supply is plugged into the socket. To completely
disconnect the power supply it must be unplugged from the mains
socket.
DANGER TO LIFE! Never open the power supply. Otherwise
there is a risk of electric shock.
Never cover the power supply.
Immediately unplug the power supply if you notice unusual noises
or smoke.
Position the cable so as to avoid a trip hazard.
Protect all plug connectors from moisture.
Application
Do not use the camera in explosive environments, e.g. at tank
plants, or in dusty environments.
Observe applicable national laws if you intend to use this camera
to photograph or watch people.
Areas under camera surveillance must be marked. The respective
decals are included, please again observe the labelling require-
ments of the respective country.

13GB
Do not place any liquid-filled containers such as vases or drinks on
or near the device. Shield the power supply from drips or sprays.
Keep away from open flames. For example, do not place any
burning candles on or near the device. That way you can avoid
the spread of fire.
Trademark notices
iOS and Apple are registered trademarks of Apple Inc in the USA and
other countries. App Store is a registered trademark of Apple Inc.
Android and Google Play are registered trademarks of Google Inc.
Other names, trademarks and products listed in these instructions are
the property of the respective owners and may be protected.
Installing the camera
Note: Mount the camera at a height and position at which it cannot
be reached without aid. Proceed likewise with the connecting and
Ethernet cable.
Be sure not to pierce electrical lines or other obstructions during
installation.
Before mounting the product to the wall, check which mounting
materials are suitable for your wall.
Hold the mounting bracket 2against the wall in the desired
mounting position and mark the drill holes on the wall using the
predrilled holes.
CAUTION! RISK OF INJURY! Please refer to your electric
drill‘s instructions for use.

14 GB
Now drill the mounting holes (Ø 5mm). Ensure that you do not
damage the supply line.
Drill an additional hole (approx. ø 18mm) into the middle of the
three mounting holes.
Feed the camera connecting cable through one of the three cable
guides in the mounting bracket 2.
Loosen the wing bolt on the mounting bracket 2and adjust the
viewing angle (see Fig. A2).
Then secure the joint by tightening the wing bolt.
Screw the camera 1onto the mounting bracket 2(see Fig. A3).
Feed the camera connecting cable through the bore.
Now insert the wall plugs 5into the bores.
Secure the mounting bracket 2to the wall using the screws 6
(Fig. A1).
RJ45
Once the you have turned the camera
1
on the screw in the mounting
bracket 2so it is connected as tight as possible, turn the triangle
nut in the opposite direction to secure the camera 1.
Note: For details and more information, please refer to the in-
cluded tutorial CD 4.

15GB
Connecting the camera (see Fig. B)
Connect the Ethernet cable 8with the router.
Plug the connector of the power supply 7into the camera 1.
Plug the power supply 7into the socket. If the connecting cable
is too short, please contact our service department (see „Service
Address“ for the address) to order the 1.8m low voltage cable
model number EXT180 to extend it.
Wait about 45 seconds after connecting to the electric circuit. Once
the red and green LED on the camera light up, it is connected to
the network.
The red LED indicates the camera is connected with the power
supply. The green LED indicates the camera is connected with the
router.
Note: To use the camera to record, insert an SD card in the SD slot
(see Fig. B).
Open the rubber cover.
Slide the SD card, pins down, into the SD slot 11 .
Carefully push the SD card against the resistance of the spring.
The SD card is now locked in place.
To remove the SD card, lightly push against the SD card using
your fingernail.
The spring will now slightly push the SD card out of the SD slot 11 .
The SD card can now be removed.
Close the rubber cover to prevent water from entering.

16 GB
Camera setup
Note: The screen shots may vary slightly due to software updates.
Download the „OMGuard HD“ app from the App Store or Google
Play (see Fig. C).
In the app, select „Add new system“ and „Scan“ to select the
camera 1you wish to connect to the router. This will open a new
window with all the cameras available on the network. The camera
will have an alphanumeric code which also corresponds with the
„DID Code“ printed on a label on the underside of the camera.
Compare the codes and select it in the display. For iOS devices,
select the correct DID code (if several codes appear) and select
„Join“. For Android devices, select the correct DID code. Choose
a name for the camera and enter it under system name. Then enter
the default security code „123456“ and press „save“ (see Fig.
D). The camera will capture a still frame and show it in the display
along with the message „Connected“. If the DID code does not
appear automatically, you may enter it manually. To do so, select
„DID“.

17GB
Changing passwords and configuring the
camera on the WLAN network (see Fig. E)
Note:Please refer to page 17 of the instructional CD and the follow-
ing pages for detailed instructions.
For additional camera settings, select the „ “ icon and, then
„System Information“.
Select „Advanced“ (IOS) or „Menu“ (Android) and enter the de-
fault admin password „123456“. Click „OK“ to confirm.
Opening „Advanced“ (IOS) or „Menu“ (Android) for the first time
will open a window prompting you to enter a new admin pass-
word. You will need to enter a new password or you will be una-
ble to access the settings.
Note: We recommend selecting a complex password. A complex
password contains at least one uppercase letter (A, B, C, etc.) and
lowercase letters (a, b, c, etc.) and at least one number (1, 2, 3,
etc.). Special characters (&, @, =, +, etc.) may not be used.
To change the password at a later time, open the „Advanced Set-
tings“ menu and scroll all the way up to „Admin Password“. Then
enter your old password, followed by the new one. Enter the new
password again to confirm.
Scroll down until you see the field „Security Code“. Select „Change“.
Enter the default old password („123456“) and select a new
password and repeat to confirm your entry. Click „OK“ to confirm
your entry.
Scroll down until you see the „WiFi Settings“ field. Select „Man-
age WIFI Network“ (see Fig. G).
Once you have successfully entered your WLAN password the
camera will restart. Please disconnect the network plug from the
router when restarting.

18 GB
The security code allows you to access the camera („Live View“,
not for changing settings) and the „Admin Password“ is used to
change any camera settings.
IMPORTANT: The camera software requires two passwords – the
security code for accessing the camera, and the admin password for
configuring the camera.The factory setting for both passwords is
„123456“. After changing the passwords the new passwords must be
used, not the default password. Please remember the passwords.
Be sure to change both passwords to prevent unauthorised access
to the camera.
Note: We recommend selecting a complex password. A complex
password contains at least one uppercase letter (A, B, C, etc.) and
lowercase letters (a, b, c, etc.) and at least one number (1, 2, 3,
etc.). Special characters (&, @, =, +, etc.) may not be used.
Using the camera
Please check the preview image (still frame) (see Fig. H). Select
the camera image and enter your new security code. You will now
see the „Live Image“ from the camera (see Fig. I).
Live view
For iOS devices, select from the app for a live camera view
(see Fig. H, right).
Or for ANDROID devices select to view a camera recording
(see Fig. H, left).
Taking a screen shot
Select to take a screen shot. The picture will be saved to your
mobile and gallery/photos.

19GB
Switching audio on /off
Select to switch the audio on/off in LIVE mode.
Recording
Select to record. It will then record for one minute and stop au-
tomatically. The red Record icon will appear in the top right corner
whilst recording.
Return to app
Select to return to the home screen in the App.
Using the Playback function
To use the playback function, select , then from the home
screen of the app.
This will bring up a window where you will first need to select a
timeframe. Now select the file you wish to play from the events log
(see Fig. J, Android: left, IOS: right). The app will now start the
playback.
Use the pause symbol to pause playback, use return to the
playback list.
At the very top you will see information related to name, connec-
tion and image quality*.
There are 4 displays:
– camera name: user specified
– connection status: connecting/connected /disconnected
– Resolution information: various by resolution selected.
(1280X720HD/640X480VGA)
– connection type and connection quality: unknown (app does
not recognise the type of connection)/Direct link (camera and
mobile on the same network)/Indirect link (camera and phone
on different networks - connected via internet) Connection qual-
ity = good/normal/poor.

20 GB
Note: For details and more information, please refer to the included
tutorial CD 4.
Notice to Android users: Close the app after viewing the camera
image on your mobile. To do so, from the main screen in the app,
press and hold the respective button at the bottom left corner of the
display.
Note: Depending on the operating system and version you may not
have full access to all functions.
Troubleshooting
No image appears.
Check the display (LED) on the camera.
Verify the camera is connected to power with the included
adapter.
Check the connections of the Ethernet cable.
The camera does not respond, the camera image freezes.
To reset the camera, hold the Reset button for approx. 45 seconds
until both LEDs have simultaneously flashed several times. After re-
leasing the RESET button 10 it will take approx. 45 seconds for
the camera to reconnect to the network. After this, the red and
green LED will light up. The green LED will light up when the cam-
era is connected to the tethered network. The camera is now
again ready for use.
All settings will be reset to the factory settings. It will need to be
completely reconfigured.

21GB
A poor image will appear.
Do not set up the camera directly behind a glass pane.
Do not aim the camera directly at a light source.
If necessary, clean the camera lens (carefully, using a slight damp
cloth).
Unable to connect to the camera.
Check if the camera and smartphone/tablet are on the same
WLAN network.
Note: For details and more information, please refer to the included
tutorial CD 4.
Cleaning and Care
When cleaning, first switch off the product at the mains.
Do not use solvents, petrol, etc. Doing so would damage the
product.
Never immerse the product in water.
Only use a dry, lint-free cloth for cleaning.
Disposal
The package and packaging materials consist entirely of
environmentally friendly materials. They can be disposed of
at your local recycling facility.
Do not dispose of electric equipment in the
household waste!

22 GB
The symbol with the crossed out wheelie bin means the device is subject
to directive 2012/ 19/ EU and must never be disposed of in normal
household waste. They must be taken to a special waste electrical
equipment collection point. Information on free and environmentally-
friendly disposal of old electronic devices can be found at your local
council or at a disposal site. Keep your environment clean and dispose
of the device correctly. Thank you.
Warranty and Service
Warranty Declaration
The camera is covered by a 3 year warranty from the date of purchase,
granted only the original buyer, and is not transferrable. Please keep
your receipt as your proof of purchase.
The warranty applies to material or manufacturing defects only. It does
not cover worn items or damage caused by improper use. Any modifi-
cations will void the warranty. This warranty does not limit your legal
rights. In the event of a warranty claim, please first contact the service
department by phone. This is the only way to return your product free
of charge.
Service address
Teknihall Elektronik GmbH
Breitefeld 15
DE-64839 Münster
GERMANY
Tel: [phone]