SME Model 6 User manual

INTEGRATED PRECISION TURNTABLE
OWNERS MANUAL

Instructions
This is no ordinary turntable.
These instrucons include unpacking, set up procedures and specicaons.
Please read carefully.
INTEGRATED PRECISION TURNTABLE

Warning! Important Safety Instrucons
CAUTION: RISK OF ELECTRIC SHOCK DO NOT REMOVE POWER UNIT COVER.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE SPEED CONTROL UNIT (POWER UNIT)
COVER. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
• Please read this manual carefully and keep it in a safe place for future reference.
• The vent slots in the underside of the Speed Control Unit are for necessary venlaon. To ensure reliable operaon of this apparatus
and to protect from overheang these vents must never be blocked or covered.
• Do not place a water containing vessel on this apparatus, as this can result in a risk of re or electric shock. Do not expose this apparatus
to rain or place it near water.
• If this apparatus accidentally gets wet, unplug it and contact an authorised dealer immediately.
• You can clean this apparatus with a damp cloth when necessary, but be sure to unplug the apparatus rst. To cut o the power source,
unplug the apparatus from the AC wall outlet.
• Do not overload AC wall outlets, power cables or adaptors beyond their capacity as this can result in re or electric shock.
• Power cables should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying
parcular aenon to cables at the plug end, adaptors and the point they exit from the appliance.
• Before connecng the AC power cable to the Speed Control Unit, make sure the voltage of the Power Unit, as marked on the idencaon
label at the rear, corresponds to the local electricity supply.
• Never insert anything metallic into the open parts of this apparatus.
• Only a qualied technician should remove the Speed Control Unit cover.
• Be sure to hold the plug, not the power cable, when disconnecng this apparatus from an electric socket.
• Locate this apparatus near an easily accessible AC outlet.
• If this apparatus does not operate normally, in parcular if there are any unusual sounds or smells, unplug it immediately and consult
an authorised dealer.
• Unplug this apparatus from the AC outlet before any service.
1

IMPORTANT NOTICE:
The power cable on this equipment when supplied for use in the UK, is ed with a moulded plug incorporang a fuse. The value of the
fuse is indicated on the pin face of the plug and if it required replacing a fuse approved to BSI 1362 of the same rang must be used. Never
use the plug with the fuse cover omied if the cover is detachable. If the plug ed is not suitable for the power points in your room or if
the power cable is not long enough to reach the power point, you should obtain a suitable safety approved extension lead or consult your
dealer for assistance.
IMPORTANT:
The wires in the power cable are coloured in accordance with the following code: BLUE NEUTRAL, BROWN LIVE. As these colours may not
correspond to the coloured markings idenfying the terminals in your plug, proceed as follows: The wire coloured BLUE must be connected
to the terminal marked with the leer N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked
with the leer L or coloured BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER (E) OR BY THE EARTH SYMBOL OR
COLOURED GREEN OR GREEN/YELLOW.
WEEE SYMBOL INFORMATION
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable to the European Union and other European countries with separate collecon system).
The marking shown on this product or its literature, indicates that it should not be disposed with other household wastes at the
end of its working life. To prevent possible damage to the environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the sustainable re-use of material resources.
Household users should contact either the retailer where they purchased this product or their local government oce,
for more detailed informaon of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and condions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
2

Introducon
SME is an iconic brand founded in 1946 by audio legend Alastair Robertson-Aikman in
West Sussex, England. Today SME is recognised as makers of the nest precision turntables
and tonearms in the world. Enrely made in-house by state of the art manufacturing
processes, complemented by tradional crasmanship methods. SME audio has evolved
from 75 years of engineering excellence, innovaon and perfecon delivering precise and
pure audio reproducon.
The Model 6 is a precision turntable with a CNC machined chassis made from a unique
polymer high density resin material which provides high mass and superb resonance
absorpon. The chassis is complemented by a specialist isolaon system incorporated
into the self-levelling feet. The main bearing, spindle and drive pulleys are precision made
to the same exact standards as all SME high-end turntables. Speed control is a highly
sophiscated bi phase, frequency and amplitude, DSP based sine wave generator, with a
dedicated discrete power amplier to drive the motor. It generates two pure sine waves
which drive twin coils present inside a custom made AC motor. The frequency (speed) is
user adjustable in approximately 0.0133 Hz steps allowing a very accurate musical pitch
to be set.
The Model 6 is equipped with the highly credible SME M2-9 tonearm which is of
meculous build quality. Primary features include lightweight stainless steel tonearm
tube, detachable aluminium headshell with double draw pins for extra rigidity and azimuth
adjustment, thumbwheel vercal tracking adjustment, tungsten balance weight(s) and
high quality ball race bearings in all planes. The M2-9 tonearm is designed to suit a wide
range of cartridges up to 38 grams and with a direct plug-in head up to 46 grams.
Design and engineering excellence built by audio enthusiasts for audio enthusiasts.
3

Contents
1 Weights & Dimensions
2 Packing List
3 Parts Idencaon
4 Unpacking
5 Seng Up
6 Operaon – Speed Control
7 Operaon – Turntable
8 Tonearm
9 Maintenance
10 Transit Precauons
11 Guarantee
4

1. Weights & Dimensions (mm)
Turntable
Width: 420
Depth: 320
Height: 128
Plaer Diameter: 300
Spindle to Arm: 215.4
Net Weight: 9.1kg
Speed Control Unit
Width: 220
Depth: 200
Height: 85
Net Weight: 2.05kg
5

2. Packing List
Qty Descripon 3
1 Packing List for Model 6 □
1 Model 6 Serial No □
1 M2-9 Tonearm □
1 Control Unit – 100V □ 115V □ 230V □ □
1 Power Cable – UK □ EU □ USA □ □
1 Plaer □
1 Stroboscopic Disc □
1 Record Clamp □
1 Spindle Washer □
1 Drive Belt □
1 Velcro Strap □
1 Balance Weight □
1 Accessory Weight □
1 Detachable Headshell □
1 Finger Li & Washers □
1 Cartridge Screw Set □
1 Bias Weight □
1 Bias Guide □
1 2mm Hex Wrench □
1 0.89mm Hex Wrench □
1 Alignment Protractor □
1 Owner’s Manual □
6

2
5
6
11
10
9
8
7
1
3
4
1. Speed Control Unit
2. Power ON/OFF Buon
3. Rotary Speed Control
4. Plaer
5. Bias Weight
6. Bias Guide
7. An-Skate Lever
8. Balance Weight
9. Tonearm
10. Finger Li
11. Headshell
3. Parts Idencaon
7

8
Power Cable & Phono Connectors
Idencaon
Low Voltage
Power Cable 24V
Phono Output
Sockets
Power
ON / OFF
Earth Point
AC Power
Cable Socket
Low Voltage Input
Socket 24V

9
5. Seng Up
1. With the turntable sited, follow the set
up instrucons in the order detailed.
2. Drive belt installaon: place the belt
over the driven pulley, pressing it down
as far as the lower ange and ensuring
free from twists and stretch the belt
over the motor pulley. Rotate the
driven pulley slowly by hand to posion
the belt on the pulleys.
3. Plaer tment: ensure the upper face
of the driven pulley and the underside
of the plaer mang surfaces are
clean, place the plaer squarely over
the turntable spindle lowering it gently
unl it rests on the driven pulley.
4. Unpacking
1. Unpack and check all items against the
packing list in Secon 2. In the very
unlikely event that anything is missing
your dealer should be noed at once.
2. The design of the turntable allows it
to be used on any substanal table or
similar piece of furniture in the absence
of a dedicated audio equipment stand.
4. Speed control unit: t the mains power
cable (check carefully that this matches
your mains power voltage). The mains
voltage seng is indicated on the back
panel.
WARNING! To meet internaonal
safety standards the control unit is
earthed through the yellow/green
wire of the power cable and parcular
care must be taken to ensure that
this is connected in order to maintain
eecve earthing.
5. Low voltage connecon cable: connect
the speed control unit to the turntable
by inserng the cable plug into the
24v input socket at the rear of the
turntable.

6. Timeout: if in adjustment mode and
no adjustments have been made for 20
seconds the new sengs will be saved
and the system will exit adjust mode
and resume running normally.
7. Cancel/Abort Adjustment: with the
motor running and the system in
adjustment mode, if the power buon
is pressed, the motor will stop and any
adjustments that have been made will
be discarded and not saved.
7. Operaon – Turntable
1. Turn on mains power at rear of the speed
control unit (push ON/OFF switch).
2. Place record spindle washer on spindle
followed by the record.
3. Fit record clamp by holding main body
of the clamp and turn locking knob
gently about 1⁄4 turn.
4. Select required speed by pressing the
rotary control buon on speed control
unit unl 33 or 45 is indicated.
5. Press power buon.
6. You are now ready to play your record.
10
appear staonary when the speed is
correct. Whilst forward and reverse
band movement will indicate fast or
slow running respecvely. This is best
observed with the cartridge ed and
the tonearm in the raised posion and
placed directly over the band being
viewed as a reference point.
4. Speed Adjustment: with the motor
running press and hold the rotary buon
for two seconds, the speed indicator
LED will begin to ash. The motor is now
in speed adjust mode and the speed
can now be adjusted in conjuncon
with the stroboscopic disc. Turning the
rotary buon an-clockwise will reduce
speed and clockwise will increase
speed. The method provides a microne
incremental adjustment. When the
speed adjustment is completed depress
and release the rotary buon, the speed
indicator LED light will stop ashing and
become constant and the speed seng
will be stored in the system memory for
future use.
5. Repeat this process for the 45rpm speed
range if required.
The Model 6 precision turntable is
extensively run-in and it’s speeds set before
leaving the factory. If you should wish to
check the speed sengs and make your own
adjustments, the procedure is as follows:
1. Mains Power: the power ON/OFF
buon is located on the rear of the
speed control (power unit). With power
ON the last used speed indicator LED
light will illuminate on the speed control
unit fascia.
2. Motor Power: pressing the power
buon on the speed control unit fascia
will start the motor. With power OFF and
pressing the rotary buon on the fascia
the speed sengs of 33 and 45rpm will
cycle and be indicated by the speed LED.
With the motor running, pressing the
power buon will stop the motor.
3. Speed Tesng: the stroboscopic disc
installed on the plaer is used to check
speeds of 33 and 45rpm. Use the strobe
bands appropriate for your mains AC
frequency. The disc should be viewed
in a uorescent or neon light. The
appropriate band will synchronise and
6. Operaon – Speed Control

11
Note:
Tonearm images for references only, mounng base plate prole may vary.
For your convenience the headshell is supplied detached from the tonearm ready for tment of your cartridge.
Cartridge not supplied – images of cartridge used for illustraon purposes only.
8. Tonearm
• General Arrangements
• Dimensions
• Specicaons
• Fing Balance & Bias Weights
• Fing Headshell & Cartridge
• Tonearm Set Up & Adjustment

12
General Arrangement

13
Dimensions (mm)
A – Pivot to Stylus 233.20
B – Pivot to Turntable Centre 215.40
C – Cartridge Fixing Centres 12.70
D – Oset Angle (degree) 23.630
E – Linear Oset 93.47
F – Overhang 17.80
G – Height above Mounng Surface (Max) 87.00
G Height above Mounng Surface (Min) 63.00
H – Mounng Surface to Underside of Headshell (Max) 67.40
H Mounng Surface to Underside of Headshell (Min) 43.40
I – Depth below Mounng Surface 46.00
J – Balance Weight Clearance Radius 51.00
Specicaons (g/mm)
Eecve Mass (g) 9.50
Cartridge Balance Range (g) 5-12
Vercal Tracking Force (g) 0-2.5
Maximum Tracking Error (degree/mm) 0.013
Null Point: Inner (mm radius) 66.04
Outer (mm radius) 120.90
Silver Litz Internal Wiring

14
Fing Balance & Bias Weights
The tonearm balance and bias weights are packed separately for safety in transit. Carefully screw the balance weight onto the threaded
stud on the rear of the tonearm, the dial should face forward towards the headshell.
Fing of the bias weight is described in the following set up pages.

15
Before ng the cartridge see that the
stylus guard (not illustrated) is in posion
as a precauon against accidental damage.
The cartridge leads have Ø1.2mm
receptacles to suit the cartridge.
The coding is as follows:
Red – Right Channel Signal
Green – Right Channel Ground
White – Le Channel Signal
Blue – Le Channel Ground
Most cartridges have their own screws.
One pair #3-48 UNC x 11mm with nuts
and washers are provided.
For the purist, use without the nger
li is preferred but is unlikely that any
dierence will be audible. When used
the two stainless steel washers should
rst be ed to the counterbores in the
headshell.
Examine the top of the cartridge. It is
important that it presents a good at face
to the underside of the headshell. Before
nal ghtening check that the cartridge is
lying parallel to the reference edge of the
headshell.
Tighten the xing screws securely using a
screwdriver, which must be a good t in
the screw slots to avoid damage. Hold the
nut if necessary to prevent rotaon.
Fing Headshell & Cartridge

WHITE
BLUE
RED
GREEN
WHITE
BLUE
RED
GREEN
Using the 2mm wrench release the
headshell clamp bolt and remove it. The
nut remains in its housing in the underside
of the headshell where it is retained with
adhesive.
Oer up the headshell to the tonearm
idenfying the half-round keyway near
the front.
As the headshell is pushed onto the
tonearm, resistance will be felt as the spring
loaded contact pins in the tonearm plug
are compressed.
Align the bolt hole in the headshell with the
keyway in the tonearm and insert the clamp
bolt unl it contacts the nut. Tighten lightly
using the 2mm wrench.
Using the 2mm wrench release the clamp
bolt and unscrew it. To remove the bolt
push the headshell onto the tonearm
using just enough pressure to overcome
the spring-loaded contact pins in the
tonearm plug. The clamp bolt should then
be loose enough to li out using the long
leg of the wrench whilst applying slight lt
so that it does not slip out of the socket.
16

17
Posion the tonearm so that it is clear of
the armrest and the cartridge is clear of the
turntable. Move the control lever into the
lowered posion. Balance the tonearm by
rotang the weight to move it backwards
or forwards as required.
Adjust unl the tonearm (with the cartridge ed) is either level or slightly low at the
front end.
Tonearm Set Up & Adjustment

For safety the lever of the lowering control
should now be moved into the raised
posion.
VTF is set aer longitudinal balancing has
been completed.
It is applied by rotang the weight, an-
clockwise to increase and clockwise to
decrease.
The indicator on the front face of the
weight carries the leers A-B-C-D at
quarter turn intervals.
Note the posion of one of the leers and
rotate the weight an-clockwise. One full
turn for 1.0g and 0.25g for each leer. For
example for 1.5g one and half turns will be
required.
18