Smeg SEU122B User manual

Table of Contents
3
EN
1 Installation 6
1.1 General installation instructions 6
1.2 Electrical requirements 7
1.3 Electrical connection 8
1.4 Cutting out the countertop 10
1.5 Recess 12
IMPORTANT INSTRUCTIONS
WARNING: If the instructions contained in this manual are not followed
precisely, fire or explosion may result causing property damage, personal
injury or death.
NOTE: This appliance must be installed solely and exclusively by a qualified
technician. Any technical procedures must be carried out by an authorized
technician.
READ AND SAVE THESE INSTRUCTIONS - Your safety and the safety of
others are very important.
We have provided many important safety messages throughout this manual and
on the appliance.
Read all the instructions before using the appliance and always obey all safety
messages.
RECOGNIZE SAFETY INFORMATION
This is a safety alert symbol. This symbol alerts you to potential hazards that can
result in severe personal injury or death.
UNDERSTAND SIGNAL WORDS
A signal word - DANGER, WARNING or CAUTION - is used with the safety alert
symbol. DANGER denotes the most serious hazards. It means you could be killed
or seriously injured if you do not immediately follow the instructions. WARNING
means you could be killed or seriously injured if the instructions are not followed.
CAUTION indicates a potentially hazardous situation which, if not avoided, could
result in minor to moderate injury.

Important Safety Instructions
4
The safety messages will inform you of potential hazards, how to avoid the risk of injury and
what can occur if the instructions are not followed.
IMPORTANT: Installation and grounding must conform to applicable codes. Observe
all codes and ordinances in force.
• Read all instructions
• Proper installation is your responsibility.
Have a qualified technician install and
ground this appliance in accordance
with these installation instructions.
• It is the responsibility of the installer to
comply with installation information
specified on the model/serial ID plate.
The ID plates are visibly located under
the appliance. These ID plates must
never be removed.
WARNING
• This appliance is intended for home use only.
• Use this appliance only for its intended purpose. The
manufacturer cannot be held liable for damage caused by
improper use of this appliance.
• This appliance complies with current safety regulations.
Improper use of this appliance can result in personal injury
and material damage.
• Read all the instructions before installing or using the
appliance for the first time.
• Keep these operating instructions in a safe place and pass
them on to any future user.
WARNING: For your safety, the instructions contained in this manual must be
followed to minimize the risk of fire or explosion and to prevent property damage,
personal injury or death.
NOTE: this appliance is NOT designed to be installed in motorhomes, mobile
homes, RVs or boats.
DO NOT install this appliance outdoors.
WARNING To reduce the risk of fire, electrical shock, personal injury or
damage when using the appliance, follow basic safety
precautions, including the following:

Important Safety Instructions
5
EN
• ELECTRICAL GROUNDING
REQUIRED: See the “Electrical
Requirements” section. It is the customer’s
responsibility to:
• Contact a qualified electrician to install
the appliance
• Ensure that the electrical system is
adequate and conforms with the national
ANSI / NFPA 70 ELECTRICAL CODE –
latest edition – Or the CANADIAN
ELECTRICAL CODE, C22.11 – 1 and
C22.2 No. 01982 – or latest edition –
and all local codes and ordinances.
IMPORTANT: Observe all governing
codes and ordinances.
• Never modify or alter the construction of
the appliance. For example, do not
remove adjustable legs, panels, wiring
or anti-tip brackets/screws.
• Do not obstruct appliance vents or
openings for heat exhaust.
• Test the appliance immediately after
installation, following the instructions in
this booklet. If the appliance does not
work properly, disconnect it from the
electrical power supply and call the
Customer Service Center. DO NOT
attempt to repair the appliance.
• All adjustments and servicing must be
performed by qualified installers or
service technicians.
• Do not leave the packing material
around the home. Sort the various items
of waste and take them to the nearest
specialized waste collection facility.
• Do not store or use gasoline or other
flammable vapors, liquids or materials
near this or any other appliance.
How to read the user manual
This user manual uses the following reading
conventions:
1. Order of use instructions.
• Stand-alone instruction.
SAVE THESE INSTRUCTIONS
CAUTION: This unit is designed as
a cooking appliance. For safety
purposes, never use it for warming
a room or as a space heater.
Installation
Information for the qualified
technician: installation, operation
and inspection.
Safety instructions
Information
Advice

Installation
6
1 Installation
1.1 General installation instructions
• Proper installation is your
responsibility. Have a qualified
technician install this appliance. Make
sure you have everything necessary for
correct installation. It is the responsibility
of the installer to comply with installation
guidelines specified on the model/serial
ID plate. The model/serial ID can be
found under the appliance.
• Have your appliance installed and
properly grounded by a qualified
installer, in accordance with these
installation instructions. Grounding is
mandatory according to the provisions of
the electrical system safety regulations. If
this appliance is connected to an outside
electrical power source, it must be
grounded in compliance with local laws,
or, if no local laws exist, in compliance
with the national ANSI/NFPA 70 code
of electrical regulations.
• Make sure that the voltage and
dimensions of the supply line correspond
to the information indicated on the
model/serial rating plate. A multi-pole
circuit breaker must be available on the
supply line with contact gap equal to or
greater than 3mm, located in an easily
accessible position near the appliance.
• Do not attempt to repair or replace any
part of the appliance unless specifically
recommended in this manual. All other
service procedures should be performed
by a qualified technician.
• This appliance is not suitable for
installation and use in mobile homes or
campers.
• Electrical grounding is required. See
the “Electrical requirements” section. It is
the customer’s responsibility to:
1. Contact a qualified electrical installer.
2. Ensure that the electrical system is
adequate and in compliance with the
national ANSI/NFPA 70 ELECTRICAL
CODE - latest edition - or the
CANADIAN ELECTRICAL CODE,
C22.11 - 1982 and C22.2 No. 01982
- or latest edition - and all local codes
and ordinances.
IMPORTANT: Observe all codes and
ordinances in force.
In case of multiple installations,
cooktops can not be installed
adjacent to each other.

Installation
7
EN
1.2 Electrical requirements
Make sure that the power line rating
matches the specifications indicated on the
ID plate. The ID plates are visibly located
under the appliance.
These ID plates must never be removed.
• If codes permit and a separate ground
wire is used, it is recommended that a
qualified electrician check the suitability
of the ground path.
• Wire size and connections must conform
to the requirements of the National
Electrical Code, ANSI/NFPA 70
ELECTRICAL CODE (*) – latest edition
or CSA Standard C22.1-94, Canadian
Electrical code, Part 1 (**) and CSA
C22.2 No. O-91 or latest edition and
all local codes and ordinances for the
kilowatt rating of the appliance.
IMPORTANT: Observe all governing
codes and ordinances.
• Copies of the standards listed above
may be obtained from:
• (*) National Fire Protection Association,
One Batterymarch Park, Quincy,
Massachusetts 02169-7471
• (**) CSA International 8501 East
Pleasant Valley Road Cleveland, Ohio
44131-5575.
Warning
Electrical shock hazard
• Have the electrical connection
performed by authorized technical
personnel.
• The frame is grounded by connecting
the grounding lead to the neutral lead. If
local codes do not permit grounding
through the neutral lead, open the
connection and use the grounding lead
to ground the unit in accordance with
local codes. Connect the neutral lead to
the branch-circuit neutral conductor in
the usual manner.
• Do not use an adapter.
• Do not use an extension cord.
• Check with a qualified electrician if you
are not sure whether the appliance is
grounded.
• Turn the power supply off before
connecting the wires.
• Ground the appliance electrically.
• Failure to follow these instructions can
result in death, fire, or electrical shock.
• Improperly connecting the appliance’s
grounding conductor can result in
electrical shock. Check with a qualified
electrician or service technician if you
are in doubt as to whether the appliance
is properly grounded. Do not modify the
power supply cord. If it does not fit in the
outlet, have a proper outlet installed by
a qualified electrician.
• Disconnect the main power supply.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD
RESULT IN DEATH, FIRE OR
ELECTRICAL SHOCK.

Installation
8
1.3 Electrical connection
This appliance is manufactured with a
green or green-yellow ground wire
connected to the appliance chassis.
To prepare the connection between the
appliance and the junction box:
• Disconnect the power supply to the
junction box.
• Feed the flexible cable conduit from the
appliance through the opening of the
cabinet.
• Remove the junction box cover, if
present.
• Install a UL-listed or CSA-approved
conduit connector to the junction box.
• Route the flexible cable conduit from the
appliance to the junction box through a
UL-listed or CSA-approved conduit
connector.
• Tighten the screws on the conduit
connector.
IMPORTANT: Any local codes or
ordinances should be given priority over
these instructions.
The frame is grounded by connecting the
grounding wire to the neutral wire. If the
new branch circuit installation (1996 NEC)
is used or if local codes do not permit
grounding through the neutral wire, open
the connection and use the grounding wire
to ground the unit in compliance with local
codes. Connect the neutral wire to the
branch circuit’s neutral conductor in the
usual manner:
• Disconnect the ground from the neutral
at the free end of the conduit.
• Use the grounding terminal or lead to
ground the unit.
• Connect the neutral terminal or wire to
the branch circuit neutral in the usual
manner.
Warning
Electrical shock hazard
• Disconnect power to the junction box
before connecting.
• Electrically ground the appliance using
the green or green-yellow wire.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD
RESULT IN DEATH, FIRE OR
ELECTRICAL SHOCK.

Installation
9
EN
U.S. Installation only / 3-wire branch
circuit
See diagram. Where local codes allow the
connection of the ground wire from the
appliance to the power supply cable's
neutral wire (white wire):
• The ground wire must be connected first;
• If local codes permit, connect the green
or yellow-green ground wire from the
appliance and the white wire from the
appliance to the power supply's neutral
wire (white wire).
• Connect the red and black leads from
the appliance to the matching color
wires in the junction box using UL/CSA-
listed wire connectors.
• Connect to copper wire, or, if the
connection is made to aluminum house
wiring, use UL-listed or CSA-approved
connectors approved for joining
aluminum and copper wiring.
Fixed connection
Fit the power line with a multi-pole circuit
breaker in compliance with installation
regulations.
The circuit breaker should be located near
the appliance and in an easily reachable
position.
NOTE: Both leads coming out of
the appliance must be connected
according to the diagrams shown
in the figures.
Acable from power supply bw black wires
Bjunction box gw white-green or yellow-green wires
Ccable from appliance rw red wires
DUL/CSA-listed conduit connector ww white wires

Installation
10
1.4 Cutting out the countertop
Cut an opening in the countertop of the
indicated dimensions.
The following operation requires
building and/or carpentry work
which must be carried out by a
competent technician.
The appliance may be installed on
various materials such as masonry,
metal, solid wood and wood
faced with plastic laminates,
provided they are heat resistant
(>90°C - 194°F).
Warning
Electrical shock hazard
• To eliminate the risk of burns or fire by
reaching over heated surface units,
cabinet storage space located above
the surface units should be avoided. If
cabinet storage is to be provided, the
risk can be reduced by installing a
range hood that projects horizontally a
minimum of 5 inches beyond the bottom
of the cabinets.
L X Y
11 13/16”10 3/8” 19 7/8”
300 mm 272 mm 505 mm
24” 22 3/16”19 7/8”
610 mm 563 mm 505 mm
30” 28 5/16”19 7/8”
762 mm 720 mm 505mm
36” 33 11/16”19 7/8”
914 mm 855 mm 505 mm
For proper installation, refer to the
rear mechanical spacers.
The rear mechanical spacers
should never be removed. The
possible removal is considered a
tampering with the device.

Installation
11
EN
Seal the cooktop
Before assembly, to prevent leakage of
liquid between the frame of the cooktop
and the countertop, place the provided
adhesive seal along the entire perimeter of
the cooktop.
Fastening clips
To ensure the attachment and optimal
centering, you should use the supplied clips:
1. Insert the clips and fix them in place
horizontally into the groove with light
pressure.
2. Rotate them upwards to fix them in place
permanently.
Fixing brackets
• Screw the fixing brackets into the holes
on the lower sides of the casing to
properly secure the cooktop to the
structure.
MINIMUM DISTANCE
A B C D E
5 11/16”18” 30” 1 7/8”2”
145 mm 457 mm 762 mm 48 mm 50 mm
Do not attach the cooktop with
silicone. It will prevent you from
removing the cooktop when
necessary without damage to it.
Fixing the cooktop too tightly may
strain the glass and cause it to
break.

Installation
12
1.5 Recess
Over an undercounter, built-in oven
The distance between the cooktop and the
kitchen cupboards or built-in appliances
must ensure adequate ventilation and
sufficient air exhaust.
If installed above an oven, space must be
left between the bottom of the cooktop and
the part of the product installed underneath.
On a hollow compartment or drawer
If there are other furniture parts (side panels,
drawers, etc.), dishwashers or refrigerators,
under the cooktop, a double-layer,
wooden base must be installed at a
minimum distance of 51 mm (2”) from the
underside of the cooktop to prevent
accidental contact. The double-layer base
must be removed using only the
appropriate tools.
with opening on the base
with opening on the back
If Installed Above An Oven, THE
OVEN MUST BE EQUIPPED
WITH A COOLING FAN.
In case of doubt install a double-
layer, wooden as described in the
next section
Failure to install the double-layer,
wooden base exposes the user to
possible accidental contact with
sharp or hot surfaces.