Smeg FU65-5 User manual

Table of Contents
1. IMPORTANT SAFETY INSTRUCTIONS ................................................................................. 4
2. GENERAL INSTALLATION INSTRUCTIONS ......................................................................... 5
3. PREPARE BUILT–IN OVEN .................................................................................................... 6
4. MAKE ELECTRICAL CONNECTION ...................................................................................... 8
NOTE: THIS APPLIANCE MUST BE INSTALLED SOLELY AND EXCLUSIVELY BY A QUALIFIED
TECHNICIAN. ANY TECHNICAL PROCEDURES MUST BE CARRIED OUT BY AN AUTHORIZED
TECHNICIAN.
INSTRUCTIONS FOR THE INSTALLER: these are intended for the qualified engineer who is able to
install, commission and test the appliance
3

Important Safety Instruction
4
1. IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS – Your Safety And the Safety of Others Are Very Important.
We have provided many important safety messages throughout this manual and on your appliance.
Read all instructions before using your appliance and always obey all safety messages.
RECOGNIZE SAFETY INFORMATION
This is a safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and
others.
UNDERSTAND SIGNAL WORDS
A signal word – DANGER, WARNING, or CAUTION – is used with the safety-alert symbol. DANGER
identifies the most serious hazards. It means you can be killed or seriously injured if you do not
immediately follow instructions. WARNING means you can be killed or seriously injured if you do not
follow instructions. CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
All safety messages will inform you as to potential hazards, inform you on how to reduce the risk of
injury and as to what can occur if the instructions are not followed.
IMPORTANT: Installation and grounding must comply with applicable codes. Observe all
government codes and ordinances.
WARNING
- This appliance is intended for household use only.
- Only use the appliance for its intended purpose. The manufacturer cannot be
held responsible for damages caused by improper use of this oven.
- This appliance complies with current safety requirements. Improper use of the
appliance can lead to personal injury and material damage.
- Read all instructions before installing or using the oven for the first time.
- Keep these operating instructions in a safe place and pass them on to any
further user.
SAVE THESE INSTRUCTIONS
FOR THE LOCAL INSPECTORS USE

Important Safety Instruction
5
2. GENERAL INSTALLATION INSTRUCTIONS
•Proper installation is your responsibility. Have a qualified technician install this oven. Make sure
you have everything necessary for correct installation. It is responsibility of the installer to comply
with the installation clearances specified on the model/serial rating plate. The model/serial rating
plate can be found on the internal frame of the oven, once you open the door.
•Have your oven installed and properly grounded by a qualified installer, in accordance with
these installation instructions. Grounding is mandatory according to the provisions of the
electrical system safety regulations. If this appliance is connected to an outside electrical power
source, it must be grounded in compliance with local laws, or, if non exsist, in compliance with the
national ANSI / NFPA 70 code of electrical regulations.
• Make sure that the voltage and dimensions of the supply line correspond to the characteristics
indicated on the model/serial rating plate.
• Do not attempt to repair or replace any part of your oven unless it is specifically recommended in this
manual. All other service procedures should be performed by a qualified technician.
• This oven is not suitable for assembly and use in mobile homes or campers.
•Electrical grounding is required. See the “Make Electrical Connection” section. It is the customer’s
responsibility:
- To contact a qualified electrical installer,
- To ensure that the electrical system is adequate and in conformance with the national ANSI /
NFPA 70 ELECTRICAL CODE – Latest edition – Or the CSA STANDARDS C22.1-94,
CANADIAN ELECTRICAL CODE, PART 1 AND CSA C22.2 No. O-91 – or latest edition – and
all local codes and ordinances. IMPORTANT: Observe all governing codes and ordinances.

Instructions for the Installer
6
3. PREPARE BUILT–IN OVEN
WARNING
EXCESSIVE WEIGHT HAZARD
- Use two or more people to move and install the oven
- Failure to do so can result in back or other injury.
IMPORTANT: This appliance must be integrated in any cabinets made of material which is heat resistant
up to temperatures of 194°F-90°C.
Keep to the dimensions indicated in pictures 1, 2, 3. For under-worktop positioning, keep to the
dimensions indicated in pictures 1 and 3. For column positioning, keep to the dimensions indicated in
pictures 1 and 2.
Make sure the 2 spacers “A” are fitted inside the cornice.
Remember that the upper/rear part of the cabinet must have an opening with a depth of 3 1/8” - 3 1/2” /
80 – 90 mm for proper air ventilation. The same opening must be guaranteed also in the rear/lower part
of the cabinet in under worktop installation, as shown in part Bof pictures no. 1.

Instructions for the Installer
7
It is important to follow these instructions before and during the oven installation:
• Decide the final location of the oven. Locate exsisting wiring to avoid drilling into or severing wiring
during installation.
• To avoid floor damage, set the oven onto cardboard prior to installation. Do not use handle or any
portion of the frame or trim for lifting.
• Remove the shipping materials and tape from the oven.
• Remove the literature contained in the package.
• Remove and set aside racks and other parts from inside the oven.
• Move oven and cardboard close to the oven’s final location.
• Remove oven door (see paragraph “8.2 Removing the door” in the Instruction for the User booklet)
IMPORTANT: Use both hands to remove the oven door.

Instructions for the Installer
8
4. MAKE ELECTRICAL CONNECTION
WARNING
ELECTRIC SHOCK HAZARD
- Disconnect power to the junction box before making connection
- Electrically ground the appliance with green or green-yellow colored
wire
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DEATH,
FIRE OR SHOCK.
This appliance is manufactured with a yellow and green or green ground wire connected to the oven
chassis.
To prepare connection between the oven and the junction box:
- Disconnect power supply to the junction box,
- Feed the flexible cable conduit from the oven through the opening of the cabinet,
- Remove junction box cover if it is present,
- Install UL listed and CSA approved conduit connector to the junction box,
- Route the flexible cable conduit from the oven to the junction box through a UL listed or CSA
approved conduit connector.
- Tighten screws on conduit connector,
- Refer to figures 1 and 2 below, which represent the most common way of making electrical
connection.
IMPORTANT: Your eventual local codes and ordinances must be followed first to the instructions.
NOTE: Frame grounded by connection of grounding wire to neutral wire. If used in new branch circuit
installation (1996 NEC) or if local codes do not permit grounding through neutral wire, open the
connection and use grounding wire to ground unit in accordance with local codes. Connect neutral wire
to the branch circuit’s neutral conductor in the usual manner:
- Disconnect the ground from the neutral at free end of conduit,
- Use grounding terminal or lead to ground unit, and
- Connect neutral terminal or wire to branch circuit neutral in usual manner (see pic. 2 below)

Instructions for the Installer
9
US INSTALLATION ONLY–3–WIRE BRANCH CIRCUIT
Refer to picture 1, where local codes allow the
connection of ground wire from the applliance to
the branch circuit neutral wire (white colored wire):
- The ground wire must be attached first;
- If local codes permit, connect the green or
yellow-green ground wire from the appliance
and the white wire from the appliance to the
branch circuit neutral wire (white colored wire).
- Connect the red and black leads from the oven
to the junction using a UL/CSA listed wire
connectors to the corresponding leads in the
junction box. pic.1)
US INSTALLATION AND CANADIAN INSTALLATION–4–WIRE BRANCH CIRCUIT
Refer to picture 2,
- Disconnect the green or yellow green from the
white lead;
- The ground wire must be attached first;
- Connect the green or yellow-green ground wire
from the appliance to the ground in the junction
box (green colored wire) using a UL/CSA listed
wire connectors. Do not connect grounding
wire to neutral wire in junction box.
- Connect the red and black leads from the
appliance to the corresponding leads in the
junctionbox using a UL/CSA listed wire
connectors
- Connect the white wire from the appliance to the
neutral (white colored wire) wire in the junction
box using a UL/CSA listed wire connectors.
pic.2)
Connect to a 20A fuse or circuit breaker. Connect to copper wire only or if connecting to
aluminium house wire use UL listed or CSA approved connectors, which are suitable for joining
aluminium with copper wires.
UL/CSA
listed wire
connector
UL/CSA
listed wire
connector