Snapper ELE3190R User manual

Parts Manual fo
r
Revision M,
(
L.E.
)
SINGLE STAG
E
SERIES 0 & 1
McDonough, GA, 30253 U.S.A.
TP 400-5024-M-LE-N
11/7/2007 Manual No. 7006026
SNOW THROWER
Copyright © 2007
Briggs & Startton Yard Power Products Group
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
MODEL
ELE3190R (84675)
LE3170E (80488)
LE3170R (80370)
LE3170R (84362)
LE3170R (84559)
LE3171R (7085660)
LE3171R (85660)
LE3190E (80371)
LE3190E (84364)
LE3190E (84561)
LE3190R (80487)
LE3190R (84363)
LE3190R (84560)
LE3191E (7085662)
LE3191E (85662)
LE3191R (7085661)
LE3191R (85661)

Table Of Content
s
TP 400-5024-M-LE-N
Manual No. 7006026(L.E.) SINGLE STAGE
SERIES 0 & 1 3
PAGE GROUP
4HANDLES, AUGER CONTROL
6DISCHARGE CHUTE, DEFLECTOR, CONTROL HANDLE
8AUGER HOUSING, DRIVE SYSTEM, CHASSIS
12 COVERS, ENGINE
16 DECALS (94 MODEL YEAR & EARLIER)
18 DECALS (95 MODEL YEAR & LATER) Pt. 1
20 DECALS (95 MODEL YEAR & LATER) Pt. 2
22 HARDWARE BAGS
24 ACCESSORIES- ELECTRIC START KIT
26 ACCESSORIES- FLITE SHOE KITS

TP 400-5024-M-LE-N
Manual No. 7006026 (L.E.) SINGLE STAGE
SERIES 0 & 1
4

HANDLES, AUGER CONTROL
Footnotes:
TP 400-5024-M-LE-N
Manual No. 7006026(L.E.) SINGLE STAGE
SERIES 0 & 1 5
Part No Descri
p
tionItem Qt
y
Note
1 7024645 1 BAIL, Drive Control
2 7024662 1 CABLE, Drive Control
3 7023813 1 CLIP, Wiring Harness
4 7033496 1 HANDLE, Upper
5 7091182 2 INSERT, Nylon
6 7035744 2 KNOB, 5/16-18 Wing (Black)
7 7036570 1 HANDLE, Lower
8 7091190 2 BOLT, 5/16-18 x 1-3/8” Curved Head
9 7091601 2 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
10 7091013 2 BOLT, 5/16-18 x 2” Curved Head, GR 2
11 7091511 2 NUT, 5/16-18 Hex Was 90196
12 7091612 2 * BOLT, 5/16-18 x 1-1/2” Square Neck Carriage, GR 5 Was 90582
13 7090187 2 WASHER, 5/16” Split Lock
14 7090391 2 WASHER, 5/16” Internal Tooth Lock
15 7091757 1 SCREW, #10-24 x 1-1/4” Hex Head Cap, GR 5
16 7090011 2 WASHER, #10 Flat
17 7071895 1 HOLDER, Snostik, Upper
18 7091267 1 NUT, #10-24 Hex Center Lock
19 7075342 1 HOLDER, Snostik, Lower (5/16-18 thread)
20 7075909 1 SNOW STICK
Note* The heads of item 12 carriage bolts are inside the auger housing.

DISCHARGE CHUTE, DEFLECTOR, CONTROL HANDLE
TP 400-5024-M-LE-N
Manual No. 7006026 (L.E.) SINGLE STAGE
SERIES 0 & 1
6

DISCHARGE CHUTE, DEFLECTOR, CONTROL HANDLE
Footnotes:
TP 400-5024-M-LE-N
Manual No. 7006026(L.E.) SINGLE STAGE
SERIES 0 & 1 7
Part No Descri
p
tionItem Qt
y
Note
1 7052973 1 CHUTE, Discharge w/inserts Was 59232 (Model ELE3190R;
shown)
1 7052973 1 CHUTE, Discharge w/inserts (incl. decal # 24845) Models LE3170R, LE3190R &
LE3190E
1 7052973 1 CHUTE, Discharge w/inserts Was 52978, Models 3190M,
3190E & all Series 1
2 7059231 1 DEFLECTOR, Chute (incl. decal # 24106) Model ELE3190R
2 7052975 1 DEFLECTOR, Chute (incl. decal # 24844) Models LE3170R, LE3190R,
LE3190E, 3190M, 3190E & all
Series 1
3 7091318 2 SCREW, 5/16-18 x 3/4” Hex Head Cap, GR 2 Was 90206
4 7091303 1 BOLT, 5/16-18 x 1” Short Neck Carriage, GR 5 Was 91072
5 7091076 3 WASHER, 5/16” Flat
6 7091606 1 NUT, 5/16-24 Hex Center Lock, GR B Was 91074
7 7035744 1 KNOB, 5/16-18 Wing (Black)
8 7091021 2 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5
9 7046340 1 HANDLE, Chute Control
10 7091612 2 BOLT, 5/16-18 x 1-1/2” Square Neck Carriage, GR 5 Was 90582
11 7091601 3 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
12 7090316 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 Was 91097
13 7019692 1 WIRE, Safety
14 7023673 2 FASTENER, Push On, .156 Internal Diameter
15 7074198 3 CLIP, Guard Tinnerman # C2980
16 7092077 3 SCREW, #8-32 x 1/2” Pan Head Cross Recess
17 7092078 3 NUT, #8-32 Hex (w/free spinning external lock washer)

AUGER HOUSING, DRIVE SYSTEM, CHASSIS
TP 400-5024-M-LE-N
Manual No. 7006026 (L.E.) SINGLE STAGE
SERIES 0 & 1
8

AUGER HOUSING, DRIVE SYSTEM, CHASSIS
Footnotes:
TP 400-5024-M-LE-N
Manual No. 7006026(L.E.) SINGLE STAGE
SERIES 0 & 1 9
Part No Descri
p
tionItem Qt
y
Note
1 7052968 1 * ASSEMBLY, Auger Housing 17” Models
1 7052969 1 ASSEMBLY, Auger Housing 19” Non-Euro Models
1 7059233 1 ASSEMBLY, Auger Housing Model ELE3190R
2 7052963 1 ASSEMBLY, End Frame, L.H. 17” Models
2 7052964 1 ASSEMBLY, End Frame, L.H. 19” Models
3 7041335 1 FRAME, End, R.H. 17” Models
3 7041333 1 FRAME, End, R.H. 19” Models
4 7026116 1 COVER, R.H. Side 17” Models
4 7026117 1 COVER, R.H. Side 19” Models
5 7034327 1 ** GUARD, Belt Drive fits all models
6 7052939 1 ASSEMBLY, Auger (incl. items 49 thru 52) 17” Models
6 7052940 1 ASSEMBLY, Auger (incl. items 49 thru 52) 19” Models
7 7090361 1 SCREW, 5/16-18 x 5/8” Hex Washer Self-Tap
8 7014098 3 WASHER, 5/16” Flat
9 7014608 2 BALL BEARING
10 7034385 2 RETAINER, 1-3/4” O.D. Bearing
11 7010935 2 WASHER, 3/4” Shim
12 7091012 9 SCREW, #10-32 x 3/8” Hex Washer Self-Tap (Torx)
13 7018635 1 PULLEY
14 7033457 1 BRACE, Engine
15 7091084 2 SCREW, 1/4-20 x 3/8” Hex Washer Self-Tap
16 7090316 1 BOLT, 5/16-18 x 3/4” Short Neck Carriage, GR 5 Was 91097
17 7019381 2 COVER, Wheel 94 Model Year & earlier
18 7091601 4 NUT, 5/16-18 Hex Flange Lock, GR 5 Was 91070
19 7091081 4 SCREW, 1/4-15 x 1” Hex Washer Self-Tap
20 7090187 7 WASHER, 5/16” Split Lock
21 7091511 5 NUT, 5/16-18 Hex Was 90196
22 7022179 1 PULLEY, Engine
23 7090233 1 SCREW, 5/16-24 x 3/4” Hex Head Cap, GR 5
24 7024618 1 V-BELT, 3L Section, 34.27” effective length Snapper part no. printed on part
25 7024800 1 GUIDE, Cable 17” Models
25 7024743 1 GUIDE, Cable 19” Models
26 7012306 1 BUSHING, Flange
27 7024228 1 PULLEY, Nylon
28 7033729 1 GUIDE, Belt
29 7091575 2 NUT, 5/16-18 Hex Center Lock Was 91067
30 7033695 1 BRACKET, Idler Pivot
Note* Riveted housing, throat & ring assembly with scraper installed
Note** 1994 & earlier models use a different belt guard & one hex spacer. If replacing item 5 belt guard, install (2) item 44
hex spacers & hardware.

AUGER HOUSING, DRIVE SYSTEM, CHASSIS
TP 400-5024-M-LE-N
Manual No. 7006026 (L.E.) SINGLE STAGE
SERIES 0 & 1
10