Snapper SS5200E User manual

Parts Manual fo
r
Revision 3,
520 Single Stage Snow Throwe
r
Series 0 & 1
TP 400-5006-3-LE-N
11/20/2006 Manual No. 7006178
McDonough, GA, 30253 U.S.A.
Copyright © 2006
Briggs & Startton Yard Power Products Group
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation
MODEL
SS5200
E
SS5200
R
SS5201
E
SS5201
R

Table Of Content
s
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 3
PAGE GROUP
4Frame, Handle, & Engine Group
8Auger Housing and Chute Group
12 Auger and Drive Group
16 Decal Group

Frame, Handle, & Engine Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
4

Frame, Handle, & Engine Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 5
Part No Descri
p
tionItem Qt
y
Note
1 1720525 1 HANDLE, Auger Control
2 1720641 1 HANDLE, Upper
3 1921961 3 CAPSCREW, Hex Head, 1/4-20 x 1-1/4”
4 1923358 1 NUT, Hex Centerlock, 1/4-20
5 1720323 1 CABLE, Auger Control
6 925094 1 TIE, Self Locking
7 1931338 2 BOLT, 5/16-18 x 1-3/4” Round Head
8 1716678 1 SNAP BUSHING, 3/8
9 1720574 1 BRACKET, Chute Rotator Rod
10 1933896 1 NUT, Hex Lock, #10-24
11 1920397 4 NUT, Hex Lock Esna, 1/4-20
12 7035744 2 KNOB, Wing (5/16-18 Black) was 1716632
13 1717312 2 WASHER, Curved, 5/16”
14 1720573 1 HANDLE, Lower
15 1919326 6 WASHER, 5/16 I.D. x 3/4 O.D. Flat
16 1921332 6 CAPSCREW, Hex Head, 5/16-18 x 3/4”
17 1921333 2 CAPSCREW, Hex Head, 5/16-18 x 1” ref. Snapper part no. 7027168
18 1917356 4 LOCKWASHER, 5/16”
19 1921332 4 CAPSCREW, Hex Head, 5/16-18 x 3/4”
20 7015368 1 CORD, Extension (Electric Start Models)
21 1716608 1 SHAFT, Axle
22 1924940 4 WASHER, .41 I.D. x .87 O.D.
23 7100909 2 TIRE, Semi-pneumatic replaces 1716607
24 1716622 2 RING, Retainer, Ext., #37
25 7100088 2 CAP, Hub replaces 1716664
26 1716613 1 WELDMENT, Frame Assy.
27 1719541 1 BRACKET, Reinforcement
28 1919438 9 NUT, Hex Lock, Esna, 5/16-18
29 1720322 1 STRAP, Support
30 960604 1 SCREW, Hex Washer Head, #10-24 x 1-1/4”
31 1 * ENGINE, Manual Start Mod HSK850-8319D
31 1 * ENGINE, Electric Start Mod HSK850-8325D
32 1716638 1 BRACKET, Fuel Tank
33 1923341 2 CAPSCREW, Hex Head, 1/4-20 x 3/4”
34 1716646 1 CAP, Fuel Tank
35 1716634 1 TANK, Fuel
36 1921319 2 WASHER, .27 I.D. x .62 O.D.
NOTE: * See your local Tecumseh distributor for service parts.

Frame, Handle, & Engine Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
6

Frame, Handle, & Engine Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 7
Part No Descri
p
tionItem Qt
y
Note
37 1723104 1 HOSE CLAMP (worm type) or 1679061 (Hose Clamp, Wire)
38 1716681 1 HOSE, Fuel, 5-1/2” long
38 7076272 1 HOSE, Fuel, 8-1/2” long
39 1960112 3 HOSE CLAMP, Wire Form
40 173206 1 FILTER, Fuel
41 1716676 1 SNAP BUSHING, 1/4”
42 1720640 1 BRACKET, Starter Handle
43 7041954 1 HANDLE, Start (Mitten)
44 7075342 1 HOLDER, Snostik- Lower (5/16-18 thread)
45 7071895 1 HOLDER, Snostik- Upper
46 7091757 1 SCREW, #10-24 x 1-1/4” Hex Head Cap
47 7090011 2 WASHER, #10 Internal Tooth Lock
48 7091267 1 NUT, #10-24 Hex Center Lock
49A 7075909 1 SNOW STICK
49B 1733209 1 SNOW STICK w/Brush replaces 7075909
NOTE: * See your local Tecumseh distributor for service parts.

Auger Housing and Chute Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
8

Auger Housing and Chute Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 9
Part No Descri
p
tionItem Qt
y
Note
1 7075689 1 HOUSING, Upper Plastic w/Louvers 520 Snow Snapper Red Part
2 1928732 2 SCREW, Hex Head, Taptite #10-24 x 1”
3 1960593 2 NUT, Retainer, Speed #10-24 w/Extrusion
4 1716628 1 COLLAR
5 1923341 9 CAPSCREW, Hex Head, 1/4-20 x 3/4” GR 5
6 1716640 1 GASKET
7 1716625 2 RETAINER
8 1716641 1 RETAINER, Gasket
9 1960521 8 NUT, Push for .156 dia. Stud
10 1716611 1 BASE, Chute
11 1960093 1 NUT, Push, Pal, 3/8”
12 1714084 1 KNOB, Chute, Rotate
13 1720578 1 HANDLE, Chute Rotator Upper
14 918454 2 PIN, Cotter, 1/8 x 1-1/2”
15 1716630 1 BRACKET, Gear
16 1716636 1 GEAR, Idler
17 1716635 1 GEAR, Drive
18 1927429 4 SCREW, Hex Head Taptite, 1/4-20 x 5/8”
19 1716658 1 ASSEMBLY, Universal Joint
20 1916622 2 NUT, Hex, 1/4-20
21 1916964 2 LOCKWASHER, Spring, 1/4”
22 1920397 11 NUT, Hex Lock Esna 1/4-20
23 1960001 3 SCREW, Hex Washer Slotted Head Plastite #10-14 x 5/8”
24 1716609 1 HOUSING, Auger
25 1921319 9 WASHER, 1/4”
26 1931318 4 CARRIAGE BOLT, 1/4-20 x 7/8”, GR 5
27 1716606 1 SCRAPER BAR
28 1716596 1 SCOOP
29 1933896 1 NUT, Hex Lock, #10-24
30 1933126 2 NUT, Wing 5/16-18 Lock
31 1960570 1 SCREW, Truss Head Torx, #10-24 x 5/8” GR 5
32 1716610 1 PLATE, Chute Base
33 1960001 2 SCREW, Hex Washer Slotted Head Plastite #10-14 x 5/8”
34 1960282 3 CARRIAGE BOLT, 5/16-18 x 3/4”
35 1919326 3 WASHER, 5/16
36 1919438 4 NUT, Hex Lock ESNA Light 5/16-18

Auger Housing and Chute Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
10

Auger Housing and Chute Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 11
Part No Descri
p
tionItem Qt
y
Note
37 1716612 1 CHUTE
38 1931335 2 CARRIAGE BOLT, 5/16-18 x 1”, GR 5
39 1716642 2 WASHER, Octagon
40 1716624 2 WASHER, Rubber
41 7035744 1 KNOB, Wing (5/16-18 Black) was 1716632
42 1920283 2 WASHER, 1-1/2 O.D.
43 1716631 1 DEFLECTOR, Chute
44 1720576 1 HANDLE, Chute Rotator Lower, E-Coat
45 1720577 1 TUBE, Chute Handles 1/2 OD 7.00 Long E-Coat
46 1926228 1 PIN, Spring 5/32 x 1” SAE 1095
47 1960074 1 CLIP, Hair Pin .093 Dia. Spring Wire 1.625 long

Auger and Drive Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
12

Auger and Drive Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 13
Part No Descri
p
tionItem Qt
y
Note
1 1960241 8 RIVET, Pop, 1/4 x 1/2”
2 1960570 8 SCREW, Truss Head Torx, #10-24 x 5/8” GR 5
3 1910531 8 WASHER, Rivet
4 1933896 8 NUT, Hex Lock, #10-24
5 1716595 1 FRAME, Right Side
6 1665521 2 BALL BEARING, Auger
7 1716649 2 RETAINER, Bearing
8 1718151 1 WELDMENT, Auger
9 1686705 1 KIT, Flighting Replacement (includes Ref. Nos. 10 & 11,
plus fasteners and instructions)
10 1718207 8 FLIGHTING, Rubber
11 1716661 4 CENTER FLIGHT, Rubber
12 1716590 1 FRAME, Left Side
13 1960001 1 SCREW, Hex Washer Slotted Head Plastite #10-14 x 5/8”
14 1716619 1 SHIELD, Belt
15 1716663 1 AIR DEFLECTOR
16 1929477 1 SCREW, Hex Head, #10-24 x 1-1/4”
17 905850 1 KEY, Parallel .187 x .187 x 1”
18 1716616 1 PULLEY, Drive
19 1960141 1 WASHER
20 1917356 1 LOCKWASHER, 5/16” Spring
21 1921982 1 CAPSCREW, Hex Head, 5/16-24 x 1-1/4”, GR 5
22 1921969 1 CAPSCREW, Hex Head, 3/8-16 x 1-1/2”, GR 5
23 1924940 1 WASHER, 3/8”
24 1716615 1 PULLEY, Idler ref. Snapper part no. 7010948
25 1716618 1 IDLER ARM
26 1931211 1 NUT, Flange Whiz Lock, 3/8-16
27 1923358 1 NUT, Hex Centerlock 1/4-20
29 1716656 1 ROLLER, Belt Stop
30 1716653 1 SPRING, Idler Return
31 1921960 1 CAPSCREW, Hex Head, 1/4-20 x 1” GR 5
32 1924009 1 CAPSCREW, Hex Head, 1/4-20 x 7/8” GR 5
33 1716617 1 BRACKET, Belt
34 1927429 1 SCAPCREW, Hex Washer Head Taptite, 1/4-20 x 5/8”
35 1716655 1 SPACER, Pulley
36 1716614 1 PULLEY, Driven
37 1716645 1 BELT, Drive Poly Rib J; 37.525” effective
length
38 1716589 1 BELT GUARD

Auger and Drive Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
14

Auger and Drive Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 15
Part No Descri
p
tionItem Qt
y
Note
39 1716654 1 IDLER PIVOT BOLT
40 1714055 1 FLANGE NUT, Ignition Switch, 5/8-32
41 1716637 1 CONTROL PANEL
42 1716627 1 HOUSING, Lower
43 1921319 3 WASHER, 1/4
44 1960568 2 SCREW, Hex Head, Taptite, 1/4-20 x 7/8”
45 1718337 1 SWITCH, Ignition
46 1716676 1 SNAP BUSHING, 1/4”
47 1714054 1 KEY, Ignition
48 1960595 1 SPEED NUT, 1/4-20
49 1919438 1 NUT, Hex Lock ESNA Light 5/16-18
50 1920397 1 NUT, Hex Lock Esna 1/4-20
51 960604 4 SCREW, Hex Head, Taptite, #10-20 x 1/2”
52 1933896 1 NUT, Hex Lock, #10-24
53 7014638 1 PRIMER, Tecumseh 1/4-20
54 7091100 1 NUT, 1/4-20 Hex, GR 5 or B
55 1716675 1 LINE, Primer

Decal Group
TP 400-5006-3-LE-N
Manual No. 7006178 520 Single Stage Snow Thrower
Series 0 & 1
16

Decal Group
Footnotes:
TP 400-5006-3-LE-N
Manual No. 7006178520 Single Stage Snow Thrower
Series 0 & 1 17
Part No Descri
p
tionItem Qt
y
Note
1 1716532 1 DECAL, Danger, Auger
2A 7075691 1 DECAL, 5200 Logo, Right Hand (Snapper)
2B 7100786 1 DECAL, Top Cover RH (Snapper) replaces 7075691 on SS5201R
& SS5201E
3 1717960 1 DECAL, Power-Mass (export models only) not shown
4 1716533 1 DECAL, Danger, Discharge Chute
4A 1733057 1 DECAL, Danger, Chute/Deflector replaces 7071880 on SS5201R
& SS5201E
5 1709933 1 DECAL, C.E. (export models only) not shown
6 1716669 1 DECAL, Console (electric start models)
6 1716670 1 DECAL, Console (manual start models)
7 1 DECAL, OPEI Not a Service Part.
8 1716672 1 DECAL, Auger Control
9 1716671 1 DECAL, Warning
9A 7026733 1 DECAL, Warning, Safety Instructions replaces 7073461
10 1 DECAL, Compliance Not a Service Part.
11 1 DECAL, Serial Number Not a Service Part
12A 7075692 1 DECAL, 5200 Logo, Left Hand (Snapper)
12B 7100787 1 DECAL, Top Cover LH (Snapper)
13 7073844 1 DECAL, Fuel Safety Snapper Decal
14 7100699 1 DECAL, Tec. 5HP Carb/EPA Certified or 7045000

Parts Manual fo
r
520 Single Stage Snow Thrower
Series 0 & 1
IT IS THE POLICY OF BRIGGS & STRATTON CORP. TO IMPROVE ITS
PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO.
WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD
IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION
TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED
Revision 3, TP 400-5006-3-LE-N 11/20/2006 Manual No. 7006178
McDonough, GA, 30253 U.S.A.
Copyright © 2006
Briggs & Startton Yard Power Products Group
Milwaukee, WI USA. All Rights Reserved
Briggs & Startton Corporation